1999 DODGE RAM air filter

outlet port. See Fig. 7. Start engine. Outlet pressure should not be
more 5 psi (0.4 kg/cm) less than inlet pressure. If pressure drop is
more than 5 psi (0.4 kg/cm), replace fuel filter and retest pressure.
If pressure drop is less than 5 psi (0.4 kg/cm), check for fuel
supply restriction.
NOTE: Due to very small vacuum specifications, use a scan tool and
Periphal Expansion Port (PEP) module with 0-15 psi transducer\
to perform following test.
Fuel Supply Restriction Test
Ensure transfer pump pressure is okay. Disconnect fuel supply
line at fuel transfer pump inlet. Remove plastic clip from pump inlet
and install in end of fuel supply line. Install 3/8" Adapter Hose
(6631) between fuel supply line and pump inlet. Install transducer
from PEP module to "T" fitting on adapter. Connect scan tool to
module. Start engine. Check vacuum reading with engine at full
throttle with no load. If vacuum reading is less than 6 in. Hg, check
for fuel supply air leaks. If vacuum reading is 6 in. Hg or more,
check fuel line for damage, dents and kinks. Repair as necessary. If
no problem is found, remove fuel module from fuel tank and check for
obstructions. Repair as necessary.
NOTE: A 3' section of 1/4" I.D. clear tubing and a 1/8" NPT fitting
are required for the following test.
Fuel Supply Air Leak Test
Clean area around filter inlet fitting plug, then remove
plug. See Fig. 7. Install 1/8" NPT fitting with 1/4" nipple fitting in
test port. Attach clear hose with a clamp to fitting. Place other end
of hose in a fuel container. Turn ignition switch to START position,
then release to RUN position without starting engine. Fuel transfer
pump should run for 25 seconds. After hose has been purged, watch for
any air bubbles in hose. If no bubbles exist, system is okay. If
bubbles exist, check fuel line, fittings and fuel module in tank.
Repair as necessary.
OVERFLOW VALVE
1) Fuel transfer pump delivers more fuel to fuel injection
pump than needed. Surplus fuel is routed back to fuel tank by overflow
valve. Overflow valve is used to secure fuel return line to side of
fuel injection pump. See Fig. 1. A sticking check valve in the
overflow valve may result in low power. Pressure release is set at 14
psi. (1.0 kg/cm
). If outlet valve is stuck closed, a FTC may set.
2) Clean area around outlet valve and fuel return line.
Remove valve from pump and fitting. Using regulated air pressure, test
valve by blowing into valve inlet. Valve should open at 14-16 psi. (1.
0-1.1 kg/cm
). If valve does not open, replace valve. Reduce air
pressure to 10 psi. (0.7 kg/cm). Valve should close. If valve does
not close, replace valve. Using NEW gaskets, install valve through
banjo fitting into fuel injection pump. Tighten valve to 24 ft. lbs.
(30 N.m).
FUEL INJECTOR & HIGH-PRESSURE FUEL LINES
WARNING: DO NOT allow diesel fuel to contact hot engine when checking
fuel injector, as high exhaust temperatures could cause fire.
Use care when working around high-pressure fuel lines, as
fuel is under extreme pressure and could penetrate skin,
causing personal injury. Wear safety goggles and protective
clothing when checking fuel injectors.

Check valve grommet
deteriorated, not
affecting performance .. 1 . Suggest replacement of grommet.
Check valve inoperative . A ........... (2) Require repair or
replacement.
Check valve leaking ..... A .... Require replacement of check
valve.
Check valve missing ..... C .... Require replacement of check
valve.
Check valve noisy ....... 2 ............ Suggest replacement.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A ........ ( 3) Require replacement.
Connector missing ....... C ............ Require replacement.
Leaking ................. A ............ Require replacement.
Terminal burned, affecting
performance ............ A ........... ( 3) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Vacuum hose filter
leaking ................ A .. Require replacement of filter.
Vacuum hose filter
restricted ............. A .. Require replacement of filter.
Wire lead burned ........ A .. Require repair or replacement.
Wire lead conductors
exposed ................ B .. Require repair or replacement.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
( 1) - Inoperative includes intermittent operation or out of
OEM specification.
( 2) - Inoperative includes intermittent operation.
( 3) - Determine cause and correct prior to replacement of part.









\









\









\









\









\









\









\


VACUUM HOSES
See HOSES.
VALVES
VALVE INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of

transmission and jack rearward until input shaft clears clutch disc.
Lower transmission jack and remove transmission from under vehicle.
Installation
1) To install, reverse removal procedure. Apply high-
temperature grease to pilot bushing located in end of crankshaft. Also
apply grease to release bearing bore, release fork, release fork ball
stud and drive shaft slip yoke. Apply sealer to threads of drain plug
before installing in case.
2) Align reference marks made on drive shaft(s) and "U"
joints during removal. After installing clutch assembly and housing,
tighten housing bolts nearest alignment dowels first. During final
transmission installation, install shims between clutch housing and
transmission at appropriate bolt location. Tighten all nuts and bolts
to specification. See TORQUE SPECIFICATIONS table.
TRANSMISSION (RAM PICKUP)
Removal (NV3500 & NV5600)
1) Disconnect negative battery cable. Shift transmission to
Neutral. Remove shift boot bezel screws and slide boot upward on lever
extension. Remove shift tower and lever assembly. Raise and support
vehicle.
2) On 4WD models, remove skid plate, if equipped. Remove
crankshaft position sensor. Mark drive shaft and axle yoke for
alignment reference. Remove drive shaft. Remove exhaust "Y" pipe. On
4WD models, disconnect and lower remaining exhaust pipes for
clearance, as necessary. Disconnect speed sensor harness connector.
3) Support engine using adjustable jackstand. If transmission
is to be disassembled for repair, drain lubricant from transmission.
On 4WD models, disconnect transfer case shift linkage at transfer case
range lever and remove shift lever from transmission. Remove
bolts/nuts attaching transmission to rear mount.
4) Support transmission with a transmission jack. Secure
transmission with safety chains. Remove rear crossmember. On 4WD
models, support transfer case with transmission jack and secure
transfer case to jack with safety chains. Remove transfer case
attaching nuts and move transfer case rearward until input gear clears
transmission output shaft.
5) Lower transfer case assembly and remove it from under
vehicle. On 4WD models, remove clutch slave cylinder splash shield, if
equipped. Remove clutch slave cylinder and move aside for working
clearance. Remove starter. Remove transmission splash shield. Remove
transmission harness wires from clips on transmission shift cover. On
some models, it may be necessary to remove front axle struts and oil
filter for access and removal clearance.
6) Lower transmission slightly. Remove shift tower and lever
assembly. Remove transmission-to-engine bolts. Slide transmission and
jack rearward until input shaft clears clutch disc. Lower transmission
jack and remove transmission from under vehicle.
Installation
1) To install, reverse removal procedure. Apply high-
temperature grease to pilot bushing located in end of crankshaft. Also
apply grease to release bearing bore, release fork, release fork ball
stud and drive shaft slip yoke.
2) Apply sealer to threads of drain plug before installing in
case. Align reference marks made on drive shaft(s) and axle yoke(s)
during removal. After installing clutch assembly and housing, tighten
housing bolts nearest alignment dowels first. Tighten all nuts and
bolts to specification. See TORQUE SPECIFICATIONS table.
Removal (NV4500 & NV4500HD)

1) Disconnect negative battery cable. Shift transmission to
Neutral. Remove shift boot bezel screws and slide boot upward on lever
extension. Scribe mark position of extension on shank of shift lever.
2) Raise and support vehicle. On 4WD models, remove skid
plate, if equipped. Mark drive shaft and axle yoke for alignment
reference. Remove drive shaft. Remove exhaust "Y" pipe. On 4WD models,
disconnect and lower remaining exhaust pipes for clearance as
necessary. Disconnect speed sensor harness connector and back-up light
harness connector.
3) Support engine using adjustable jackstand. If transmission
is to be disassembled for repair, drain lubricant from transmission.
See Fig. 9 . On 4WD models, disconnect transfer case shift linkage at
transfer case range lever and remove shift lever from transmission.
Remove bolts/nuts attaching transmission to rear mount.
4) Support transmission with a transmission jack. Secure
transmission with safety chains. Remove rear crossmember. On 4WD
models, support transfer case with transmission jack and secure
transfer case to jack with safety chains. Remove transfer case
attaching nuts and move transfer case rearward until input gear clears
transmission output shaft.
5) Lower transfer case assembly and move it from under
vehicle. On 4WD models, remove clutch slave cylinder splash shield, if
equipped. Remove clutch slave cylinder, and move aside. Remove
starter. Remove transmission splash shield. Remove transmission
harness wires from clips on transmission shift cover. On some models,
it may be necessary to remove front axle struts and oil filter for
access and removal clearance.
6) Lower transmission slightly. Remove shift tower and lever
assembly. Remove transmission-to-engine bolts. Slide transmission and
jack rearward until input shaft clears clutch disc. Lower transmission
jack and remove transmission from under vehicle.
Installation
1) To install, reverse removal procedure. Apply high-
temperature grease to pilot bushing located in end of crankshaft. Also
apply grease to release bearing bore, release fork, release fork ball
stud and propeller shift slip yoke.
2) Apply sealer to threads of drain plug before installing in
case. Align reference marks made on drive shaft(s) and axle yoke(s)
during removal. After installing clutch assembly and housing, tighten
housing bolts nearest alignment dowels first.
3) During final transmission installation, install shims
between clutch housing and transmission at appropriate bolt location.
See CLUTCH HOUSING BORE RUNOUT and CLUTCH HOUSING FACE RUNOUT under
CLUTCH HOUSING (RAM PICKUP) under TESTING. Press extension to scribe
mark made during removal. A 0.12-0.20" (3-5 mm) space should exist
between shift lever isolator, top edge of stub shaft and tool lower
jaw. Tighten all nuts and bolts to specification. See TORQUE
SPECIFICATIONS table.
Fig. 9: Identifying Transmission Drain Bolt (NV4500 & NV4500HD)
Courtesy of Chrysler Corp.
CLUTCH ASSEMBLY


* D RIV ETR AIN S YSTE M S U NIF O RM IN SPEC TIO N G UID ELIN ES *

1 999 D odge P ic ku p R 1500
GENERAL INFORMATION
Drivetrain/Transmission Motorist Assurance Program
Standards For Automotive Repair
All Makes and Models
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
CONTENTS
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
Drive/Power Train Assemblies
AUTOMATIC TRANSMISSION/TRANSAXLE ASSEMBLIES
DIFFERENTIAL AND FINAL DRIVE ASSEMBLIES
MANUAL TRANSMISSION/TRANSAXLE ASSEMBLIES
TRANSFER CASE ASSEMBLIES
Drive/Power Train Components
ACTUATORS (ELECTRICAL)
ACTUATORS (VACUUM)
AXLES
BEARINGS AND RACES
BELL CRANKS
BELL HOUSINGS
BUSHINGS (EXTERNAL)
CABLES (SPEEDOMETER)
CABLES (TV, DETENT AND SHIFT)
CARRIER BEARINGS
CLUTCH CABLES AND CABLE HOUSINGS
CLUTCH DISCS (MANUAL TRANSMISSION)
CLUTCH FORKS
CLUTCH LINKAGES (MECHANICAL)
CLUTCH MASTER CYLINDERS
CLUTCH PEDALS
CLUTCH PIVOTS
CLUTCH PRESSURE PLATES
CLUTCH RELEASE BEARINGS
CLUTCH SLAVE CYLINDERS (CONCENTRIC)
CLUTCH SLAVE CYLINDERS (CONVENTIONAL OR EXTERNAL)
COMPANION FLANGES
CONNECTORS
COOLER BYPASS VALVES
COOLER LINES
COOLERS
CV JOINTS
DIP STICK TUBES
DIP STICKS (FLUID LEVEL INDICATORS)
DOWEL PINS, GUIDES AND PILOT HOLES
DRIVE SHAFT FLANGES
DRIVE SHAFTS AND HALF SHAFTS
DUST BOOTS
ENGINE MOUNTS
EXCITER RINGS
FILLER TUBES
FILTERS AND SCREENS

Torn .................... A ............ Require replacement.








\









\









\









\









\









\









\


ENGINE MOUNTS
See MOUNTS (ENGINE, TRANSAXLE AND TRANSMISSION) .
EXCITER RINGS
See TOOTHED RINGS (TONE WHEELS) .
FILLER TUBES
See DIP STICK TUBES .
FILTERS AND SCREENS
FILTER AND SCREEN INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
At service interval ..... 3 ............ Suggest replacement.
Bent .................... A .. Require repair or replacement.
Exceeding service
interval ............... 3 ............ Suggest replacement.
Missing ................. C ............ Require replacement.
Near service interval ... 3 ............ Suggest replacement.
Restricted .............. A ........... ( 1) Require repair or
replacement.
Torn .................... A ............ Require replacement.
Worn, affecting
performance (metal or
nylon screen type) ..... A .. Require repair or replacement.
( 1) - Further inspection may be required to determine the
source of restriction or contamination.









\









\









\









\









\









\









\


FLANGES
See COMPANION FLANGES .
FLEX PLATES
FLEX PLATE INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Bent, affecting
performance ............ A ............ Require replacement.
Bent, not affecting
performance ............ .. ........ No service suggested or
required.
Bolt or stud holes
elongated .............. B ............ Require replacement.
Broken .................. A ............ Require replacement.
Cracked ................. A ............ Require replacement.
Ring gear worn close
to the end of its
useful life ............ 1 ............ Suggest replacement.
Ring gear worn to the
extent that it no longer

Scored .................. B ............ Require replacement.
Spring rate less than
specifications ......... B ............ Require replacement.
Worn, affecting
performance ............ A ............ Require replacement.
Worn beyond
specifications ......... B ............ Require replacement.
Worn close to the end of
its useful life ........ 1 ............ Suggest replacement.









\









\









\









\









\









\









\


PRESSURE SWITCHES
See SWITCHES.
RACES
See BEARINGS AND RACES .
RUBBER JOINTS (METALASTIC)
These joints may be found on half and/or drive shafts. They
are usually found on European vehicles featuring a three-lug drive
flange. They may be equipped with a centering ball or pin.
RUBBER JOINT (METALASTIC) INSPECTION









\









\









\









\









\









\









\


Condition Code Procedure
Drive flange bent ....... A ............. Require repair or
replacement.
Drive flange damaged,
affecting performance .. A ............ Require replacement.
Rubber drive joint
cracked ................ 2 ............ Suggest replacement.
Rubber drive joint
damaged, affecting
performance ............ A ............ Require replacement.
Rubber drive joint split
between mounting holes . A ............ Require replacement.
Rubber drive joint torn at
mounting holes ......... A ............ Require replacement.
Rubber drive joint weather-
cracked ................ .. ........ No service suggested or
required.









\









\









\









\









\









\









\


SCREENS
See FILTERS AND SCREENS .
SEALS
SEAL INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Leaking ................. A ........... ( 1) Require repair or
replacement.
( 1) - Require inspection of mating and sealing surface and
repair or replace as necessary. Check vent. A plugged

performance ............ A .. Require repair or replacement.
Fins damaged, not
affecting performance .. .. ........ No service suggested or
required.
Internal restrictions ... B .. Require repair or replacement.
Leaking ................. A .. Require repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A .. Require repair or replacement.
Tubes damaged, affecting
performance ............ A .. Require repair or replacement.
Tubes damaged, not
affecting performance .. .. ........ No service suggested or
required.









\









\









\









\









\









\









\


TRANSMISSION MOUNTS
See MOUNTS (ENGINE, TRANSAXLE AND TRANSMISSION) .
TRANSMISSION PANS
TRANSMISSION PAN INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Bent, interfering with
filter or other internal
components ............. A .. Require repair or replacement.
Leaking ................. A .. Require repair or replacement.









\









\









\









\









\









\









\


TRANSMISSION RANGE INDICATORS (PRNDL)
TRANSMISSION RANGE INDICATOR (PRNDL) INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Binding ................. A .. Require repair or replacement.
Broken .................. A .. Require repair or replacement.
Components missing ...... C .. Require replacement of missing
components.
Loose, affecting
performance ............ A .. Require repair or replacement.
Out of adjustment ....... A ................. Require repair.
Worn, affecting
performance ............ A .. Require repair or replacement.









\









\









\









\









\









\









\


TUBES
See HOSES, LINES AND TUBES .
UNIVERSAL JOINTS (CARDON OR CROSS TYPE)
UNIVERSAL JOINT (CARDON OR CROSS TYPE) INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.