1999 DODGE RAM oil pressure
[x] Cancel search: oil pressurePage 852 of 1691
Parking Brake Switch ...................... Analog Instrument Panels
Park Lights ........................................ Exterior Lights
Park/Neutral Position Switch .............................. Starters
Engine Performance
Anti-Theft System
Body Control Module
Perimeter Lighting Control Relay ................... Exterior Lights
Power Amplifier ..................................... Power Antennas
Power Antenna Module ................................ Power Antennas
Power Antenna Motor ................................. Power Antennas
Power Distribution Center ....................... Power Distribution
Generators & Regulators
Starters
Power Door Lock Motors ............................ Power Door Locks
Power Mirror Motors .................................. Power Mirrors
Memory Systems
Power Sliding Door Controller .............. Power Sliding Side Door
Power Seat Motors ...................................... Power Seats
Memory Systems
Power Steering Pressure Switch .................. Engine Performance
Power Top Motor .............................. Power Convertible Top
Power Top Relay(s) ........................... Power Convertible Top\
Powertrain Control Module ....................... Engine Performance
Analog Instrument Panels
Cruise Control Systems
Data Link Connectors
Generators & Regulators
Starters
Power Window Motors .................................. Power Windows
Power Window Relay(s) ................................ Power Windows\
Radiator Fan Motor(s) ........................ Electric Cooling Fans\
Radiator Fan Relay(s) ........................... Engine Performance\
Electric Cooling Fans
Rainsense Module .............................. Wiper/Washer Systems
Raise Relay .................................. Power Convertible Top
Remote Anti-Theft Personality (RAP) Module ....... Anti-Theft System\
Starters
Warning Systems
Seat Belt Pretensioners ................... Air Bag Restraint System
Seat Belt Retractor Solenoid .................... Passive Restraints
Seat Belt Switch .......................... Air Bag Restraint System
Passive Restraints
Shift Interlock Solenoid ................... Shift Interlock Systems
Shift Lock Actuator ........................ Shift Interlock Systems
Side Marker Lights ................................. Exterior Lights
SIR Coil Assembly (Clockspring) ........... Air Bag Restraint System\
Slip Ring (Clockspring) ................... Air Bag Restraint System\
Steering Column Switches
SRS Control Module ........................ Air Bag Restraint System
Starter Motor ............................................. Starters
Starter Interrupt Relay ................................... Starters
Starter Solenoid .......................................... Starters
Starter Relay ............................................. Starters
Steering Wheel Position Sensor .................... Anti-Lock Brakes
Stoplights ......................................... Exterior Lights
Stoplight Switch ................................ Engine Performance
Cruise Control Systems
Anti-Lock Brakes
Sun Roof ECU ........................................ Power Sun Roof
Sun Roof Motor ...................................... Power Sun Roof
Sun Roof Position Sensor ............................ Power Sun Roof
Taillights ......................................... Exterior Lights
Throttle Position (TP) Sensor ................... Engine Performance\
Page 854 of 1691
IN STR UM EN T P A N EL - A N ALO G
1999 D odge P ic ku p R 1500
1999 ACCESSORIES & EQUIPMENT
CHRY - Analog Instrument Panels
Ram Pickup, Ram Van & Ram Wagon
DESCRIPTION & OPERATION
INSTRUMENT CLUSTER
All instrument cluster gauges are air core magnetic type.
Tachometer is optional. All gauges use data transferred on Chrysler
Collision Detection (CCD) bus. Instrument cluster incorporates a
Vacuum Fluorescent Display (VFD) for odometer display.
Brake warning light illuminates when ignition is on and
parking brake is applied. Brake warning light also illuminates if
brake hydraulic system failure occurs during service brake
application. Brake warning light bulb test occurs when ignition switch
is in START position.
Oil pressure warning light illuminates when engine oil
pressure is not sufficient to open oil pressure sending unit switch.
Oil pressure warning light bulb test occurs with ignition switch in
RUN position.
All instrument clusters include these analog gauges:
* Coolant Temperature Gauge
* Fuel Gauge
* Oil Pressure Gauge
* Speedometer
* Voltmeter
Instrument clusters include these indicator lights, if
vehicle is equipped with appropriate option:
* Air Bag
* Anti-Lock Brake System (ABS)
* Brake Warning
* Check Gauges
* Cruise On
* Headlight High Beam
* Low Fuel
* Low Washer Fluid
* CHECK ENGINE
* Overdrive Off
* Rear Wheel Anti-Lock (RWAL)
* Seat Belt Reminder
* Security
* Transmission Oil Temperature (A/T)
* Turn Signal
* Upshift (M/T)
* 4WD
SELF-DIAGNOSTIC SYSTEM
WARNING: Vehicle is equipped with an air bag system. To prevent air
bag deployment, disconnect negative battery cable and wait at
least 2 minutes before servicing instrument cluster. See
appropriate AIR BAG RESTRAINT SYSTEMS article.
CAUTION: When battery is disconnected, vehicle computer and memory
Page 891 of 1691
![DODGE RAM 1999 Service Repair Manual Limited Slip
\
\
\
\
\
\
\f
Differential Model 248 (4WD) 7.3 Pts. (3](/manual-img/12/56915/w960_56915-890.png "DODGE RAM 1999 Service Repair Manual Limited Slip
\
\
\
\
\
\
\f
Differential Model 248 (4WD) 7.3 Pts. (3")
Limited Slip
\
\
\
\
\
\
\f
Differential Model 248 (4WD) 7.3 Pts. (3.4L)
\
\
\
\
\
\
\f
Model 267 (2WD) 7 Pts. (3.3L)
\
\
\
\
\
\
\f
Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
\
\f
Model 286 (2WD) 6.8 Pts. (3.2L)
\
\
\
\
\
\
\f
Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
\f
Front Axle Model 216 6.8 Pts. (3.6L)
Lubricant
\
\
\
\
\
\
\f
Model 248 7.6 Pts. (3.6L)
\
\
\
\
\
\
\
\f
Transfer Case NV231 HD 2.5 Pts. (1.2L)
Fluid
\
\
\
\
\
\
\
\f
Power Take NV021 4.6 Pts. (2.1L)
Off Adapter
\
\
\
\
\
\
\
\f
Power Drained 2.7 Pts. (1.3L)
Steering
Fluid
\
\
\
\
\
\
\
\f
A/C Charge Capacity 32 Oz. (.9Kg)
Refrigerant
\
\
\
\
\
\
\
\f
Refrigerant A/C System Capacity 7.75 Oz. (230ML)
Oil
\
\
\
\
\
\
\
\f
Fuel Tank 119" & 139" Wheelbase Vehicles 26 Gal. (98L)
\
\
\
\
\
\
\f
All Others 35 Gal. (132L)
\
\
\
\
\
\
\
\f
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
\
\
\
\
\
\
\
WHEEL & TIRE SPECIFICATIONS
TIRE REPLACEMENT
The tires on your new vehicle provide a balance of many
characteristics. They should be inspected regularly for wear and
correct inflation pressure. Chrysler strongly recommends that you use
tires equivalent to the originals in quality and performance when
replacement is needed. Failure to use equivalent replacement tires may
adversely affect the safety, handling and ride of your vehicle. We
recommend that you contact your original equipment tire dealer on any
questions you may have on tire specifications or capability.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE\
\
\
\
\
\
Lug Nut Ft. Lbs. (N.m)
BR1500 (5 Stud Wheel) ........................... 95 (130)
BR2500 (8 Stud Wheel) ........................... 135 (180)
Page 895 of 1691
CAUTION: If fuel contamination due to fungi or other microorganisms is
suspected a fuel additive with a biocide may be used. Follow
the manufacturers dosage as recommended on product label. Use
biocides ONLY when necessary, excessive use can may cause
other fuel system problems.
DIESEL FUEL CONTAMINATION
WARNING: Diesel fuel system may be contaminated with fungi or other
microorganisms. Keep contaminated fuel away from open skin
cuts or sores to prevent skin irritation or infection.
DIESEL FUEL REQUIREMENTS
CAUTION: All diesel engines have been developed to take advantage of
the high energy content of No. 2 diesel fuel or No. 2
climatized-diesel fuels. It also operates on No. 1-diesel
fuels if temperatures are expected to be extended arctic
conditions -10
\bF (-23\bC).
WARNING: Do NOT use alcohol or gasoline as a fuel blending agent. They
can be unstable under certain conditions and hazardous or
explosive when mixed with diesel fuel.
ELECTROSTATIC DISCHARGE SENSITIVE (ESD) PARTS
WARNING: Many solid state electrical components can be damaged by
static electricity (ESD). Some will display a warning label,
but many will not. Discharge personal static electricity by
touching a metal ground point on the vehicle prior to
servicing any ESD sensitive component.
ENGINE OIL
CAUTION: Never use non-detergent or straight mineral oil.
ENGINE OIL FILTER (CARTRIDGE TYPE)
CAUTION: Use of Mopar Oil Filter Cartridge (P/N 04746914) is
RECOMMENDED. The engine oil filter cartridge should be
changed at every engine oil change. Use the same type oil
that will be used in the engine.
FUEL SYSTEM SERVICE
WARNING: Relieve fuel system pressure prior to servicing any fuel
system component (fuel injection models).
HALOGEN BULBS
WARNING: Halogen bulbs contain pressurized gas which may explode if
overheated. DO NOT touch glass portion of bulb with bare
hands. Eye protection should be worn when handling or working
around halogen bulbs.
RADIATOR CAP
CAUTION: Always disconnect the fan motor when working near the
radiator fan. The fan is temperature controlled and could
start at any time even when the ignition key is in the OFF
position. DO NOT loosen or remove radiator cap when cooling
system is hot.
Page 934 of 1691
Apply light coat of engine oil on NEW .060" (1.5 mm) thick Copper
sealing washer. Install NEW Copper sealing washer on spray tip of fuel
injector. Engine oil is used to aid holding sealing washer in place.
Install new "O" ring on fuel injector. Apply small amount of engine
oil to "O" ring.
2) Ensure fuel inlet hole on side of fuel injector is
positioned toward injector connector tube. Install injector into
cylinder head bore using care not to allow injector tip to touch sides
of bore. Press fuel injector into cylinder head with finger pressure
only. Install fuel injector hold down clamp into shouldered bolt while
aligning slot in top of injector into groove in bottom of clamp.
Tighten opposite clamp bolt to specification. See TORQUE
SPECIFICATIONS.
3) Apply small amount of clean engine oil to NEW "O" ring.
Install "O" ring to fuel injector connector tube. Using finger
pressure only, press injector connector tube into cylinder head.
Connect and tighten high pressure fuel lines to specification. See
TORQUE SPECIFICATIONS.
NOTE: Fuel line fitting torque is important. Mating surfaces will
not seal if fuel line fitting is under or over-torqued.
4) To install remaining components, reverse removal
procedure. Tighten bolts to specification. See TORQUE SPECIFICATIONS.
Bleed high-pressure fuel lines. See FUEL LINE BLEEDING under FUEL
SYSTEM.
FUEL INJECTION PUMP
CAUTION: High-pressure fuel lines must be clamped securely and routed
so they do not contact each other or any other components. DO
NOT weld or substitute high-pressure fuel lines. High
-pressure lines are same length and proper high-pressure fuel
line must be installed in specified area for proper engine
operation.
Removal
1) Disconnect negative battery cables. Clean fuel lines at
cylinder head and injection pump. Clean fuel injection pump and fuel
lines at side of pump. Disconnect 9-pin electrical connector at Fuel
Pump Control Module (FPCM). Place a rag around overflow valve to catch\
excess fuel. Remove overflow valve and disconnect fuel return line.
Remove banjo bolts and fuel supply line at side of injection pump and
top of fuel filter housing.
2) Remove all high pressure fuel lines, intake air tube,
accelerator pedal position sensor, air intake housing, engine oil
dipstick tube, wiring clips, electrical connectors at intake heaters,
and engine lifting bracket. Unscrew plastic access cap at front gear
cover. Remove injection pump gear-to-injection pump shaft nut and
washer.
3) Engine may be rotated by removing dust plug from
transmission adapter plate and installing Engine Barring Tool (Snap-On
SP371) in transmission adapter plate. See Fig. 9. Rotate engine until
keyway is at 12 o'clock position.
Page 941 of 1691
![DODGE RAM 1999 Service Repair Manual Removal & Installation
See INTAKE MANIFOLD AIR HEATER RELAYS under RELAYS &
SOLENOIDS.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS \
\](/manual-img/12/56915/w960_56915-940.png "DODGE RAM 1999 Service Repair Manual Removal & Installation
See INTAKE MANIFOLD AIR HEATER RELAYS under RELAYS &
SOLENOIDS.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS \
\")
Removal & Installation
See INTAKE MANIFOLD AIR HEATER RELAYS under RELAYS &
SOLENOIDS.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS \
\
\
\
\
\
\
Application Ft. Lbs. (N.m)\
Access Plug ................................................ 11 (15)\
AFC Line-To-Fuel Injection Pump Fitting .................... 18 (24)\
Air Inlet Housing Bolt ..................................... 18 (24)\
Engine Bracket-To-Engine Bolts ............................. 18 (24)\
Engine Coolant Temperature Sensor .......................... 40 (54)\
Engine Speed Sensor Nut .................................... 18 (24)\
Fuel Injection Pump Drive Gear Nut ....................... 125 (170)\
Fuel Injection Pump Lower Bracket-To-Pump Bolts ............ 18 (24)\
Fuel Injection Pump Mount Nuts ............................. 32 (43)\
Fuel Injector Retaining Nut ................................ 44 (60)\
Fuel Line-To-Fuel Heater Fitting ........................... 18 (24)\
Fuel Line-To-Fuel Transfer Pump ............................ 18 (24)\
Fuel Supply Line Banjo Bolt ................................ 18 (24)\
Fuel Tank Strap Nut ........................................ 30 (41)\
Fuel Transfer Pump Bolt .................................... 18 (24)\
High-Pressure Fuel Line Clamp Bolt ......................... 18 (24)\
High-Pressure Fuel Line Nut (At Injector) .................. 28 (38\
)
High-Pressure Fuel Line Nut (At Pump) ...................... 18 (24\
)
Intake Manifold Air Heater Housing Bolt .................... 18 (24)\
Intake Manifold Air Temperature Sensor ..................... 20 (27)\
Intake Manifold Cover Bolt ( 1) ............................. 18 (24)
Oil Fill Plug .............................................. 21 (29)\
Overflow Valve-To-Fuel Injection Pump ...................... 24 (33)\
Park/Neutral Switch ........................................ 25 (34)\
Plastic Fuel Tank Module Lock Nut .......................... 32 (43)\
Starter Mounting Bolt ...................................... 32 (43)\
Turbocharger Oil Drain Line Bolt ........................... 18 (24)\
Turbocharger Oil Supply Line Nut ........................... 11 (15)\
Turbocharger Retaining Nut ................................. 24 (33)\
INCH Lbs. (N.m)
Air Inlet Tube-To-Turbocharger Clamp Nut .................. 72 (8.1)\
Canister Nut ............................................ 120 (13.6)\
Condenser-To-Intercooler Nut ............................. 95 (10.7)\
Condenser-To-Intercooler Screw ........................... 95 (10.7)\
Drain Valve-To-Canister Bolt .............................. 40 (4.5)\
Exhaust Pipe-To-Turbocharger Clamp Nut .................... 72 (8.1)\
Fuel Bleed Bolt ........................................... 72 (8.1)\
Fuel Injector Drain Line Assembly Retaining Clamp Bolt .. 120 (13.6)\
Fuel Injector Drain Line-To-Fuel Injector Banjo Bolt ...... 84 (9.5)\
Intake Manifold Air Heater Relay Assembly Retaining Bolt .. 40 (4.5)\
Intercooler Bolt .......................................... 17 (1.9)\
Intercooler Inlet & Outlet Duct Clamp ..................... 72 (8.1)\
PCM Mounting Bolt ......................................... 35 (4.0)\
Water-In-Fuel (WIF) Sensor ................................ 20 (2.3\
)
( 1) - Apply thread sealant to bolt threads.
\
\
\
\
\
\
\
Page 949 of 1691
Removal & Installation (Dakota, Durango & Ram Pickup 2.5L,
3.9L, 5.2L & 5.9L)
1) MAP sensor is located near throttle body and contains a 3-
pin electrical connector with an L-shaped rubber hose connecting it to
the throttle body. See Fig. 7 or 8. Remove air inlet duct or air
cleaner assembly for access to MAP sensor if necessary.
2) Ensure area around MAP sensor is clean. Disconnect
electrical connector at MAP sensor. Remove MAP sensor retaining bolts.
Remove MAP sensor while disconnecting L-shaped rubber hose from
throttle body. Remove L-shaped rubber hose from MAP sensor.
3) To install, reverse removal procedure. Ensure L-shaped
rubber hose is properly installed on throttle body and MAP sensor.
Tighten MAP sensor retaining bolts to specification. See TORQUE
SPECIFICATIONS.
Removal & Installation (Ram Pickup 8.0L)
1) MAP sensor is located on upper side of intake manifold and
contains a 3-pin electrical connector. See Fig. 9. Disconnect
electrical connector at MAP sensor.
2) Ensure area around MAP sensor is clean. Remove MAP sensor
retaining bolts. Remove MAP sensor with rubber seal gasket from intake
manifold. Rubber seal gasket is part of the MAP sensor and is not
serviceable. Inspect rubber seal gasket for damage. Replace MAP sensor
with rubber seal gasket if gasket is defective.
3) To install, reverse removal procedure. Ensure seal area in
upper intake manifold is clean before installing MAP sensor. Lubricate
rubber seal gasket with engine oil before installing MAP sensor.
Tighten MAP sensor retaining bolts to specification. See TORQUE
SPECIFICATIONS.
Removal & Installation (Ram Van & Ram Wagon)
1) MAP sensor is located near throttle body and contains a 3-
pin electrical connector with an L-shaped rubber hose connecting it to
the throttle body. See Fig. 8. Remove engine cover and air cleaner
assembly for access to MAP sensor if necessary.
2) Ensure area around MAP sensor is clean. Disconnect
electrical connector at MAP sensor. Remove MAP sensor retaining bolts.
Remove MAP sensor while disconnecting L-shaped rubber hose from
throttle body. Remove L-shaped rubber hose from MAP sensor.
3) To install, reverse removal procedure. Ensure L-shaped
rubber hose is properly installed on throttle body and MAP sensor.
Tighten MAP sensor retaining bolts to specification. See TORQUE
SPECIFICATIONS.
Fig. 7: Locating Manifold Absolute Pressure (MAP) Sensor (Dakota
2.5L)
Courtesy of Chrysler Corp.
Page 950 of 1691
Fig. 8: Locating Manifold Absolute Pressure (MAP) Sensor (Dakota
3.9L, 5.2L & 5.9L, Durango, Ram Pickup 3.9L, 5.2L & 5.9L, Ram Van &
Ram Wagon)
Courtesy of Chrysler Corp.
Fig. 9: Locating Manifold Absolute Pressure (MAP) Sensor (Ram
Pickup 8.0L)
Courtesy of Chrysler Corp.
OIL PRESSURE SENSOR