1999 CHEVROLET MONTE CARLO lock

yellowblue
6-39 Center High-Mounted Stoplamp
To reach the center high-mounted stoplamp, you must
go through the trunk.
1. Open the trunk lid. Locate the stoplamp behind the
rear seats, in front of the trunk hinges.
2. Turn the socket counterclockwise until it stops and
pull the bulb and socket out of the assembly.
3. Push in the bulb, turn it counterclockwise and pull it
out of the socket.4. Push the new bulb into the socket and turn
it clockwise.
5. Replace the bulb and socket in the assembly.
Tail/Stop/Turn Signal Lamp
1. Open the trunk. Remove the convenience net if you
have one. Unhook the net from the upper wing nut.
2. Remove the upper
convenience net wing
nut, if equipped.
3. Pull the carpet away from the rear of the vehicle.
4. Unscrew the two remaining wing nuts.
5. Pull the assembly from the body carefully.

yellowblue
6-40
6. To remove a socket, press the tab, turn the socket
counterclockwise and pull it out.
7. Pull the bulb out. Do not twist it.
8. Push the new bulb into the socket.
9. Replace the socket in the assembly.
10. Tighten the socket by turning it clockwise.
11. Install the assembly and the two lower wing nuts.
12. Replace the carpeting.
13. Replace the upper (convenience net) wing nut,
if equipped.
14. Replace the convenience net, if equipped.Back-Up Lamp
1. Open the trunk. The back-up lamp bulbs are in the
rear of the trunk lid.
2. Press the tab on the
socket, turn the socket
counterclockwise and
pull it out.
3. To remove the bulb, pull it out of the socket. Do not
twist the bulb.
4. Push the new bulb into the socket.
5. Reverse Steps 1 and 2 to replace the socket.

yellowblue
6-61
Look at the silver-colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical size
and rating.
Instrument Panel Fuse Block
Some fuses are in a fuse
block on the passenger's
side of the instrument panel.
Pull off the cover labeled
FUSES to expose the fuses.
Additional fuses are in the underhood electrical
centers on the driver's and passenger's sides of the
engine compartment.
Circuit Description
Breaker
A Not Used
B Not Used
C Power Windows
D Power Seats
E Not Used

yellowblue
6-63
Fuse Rating
Description
19 Power Accessory #1
-- Door Lock
Switches, Trunk Courtesy Lamp,
O/S Mirror Switch, (S.E.O.)
Emergency Vehicle
-Rear
Compartment Lid Lamp or
Window Panel Lamps
20 Steering Wheel Control #2
--
Steering Wheel Radio Controls
21 Air Bag
-- Air Bag System
22 Cruise Control
-- Cruise Control
Cut
-Out Switch, Cruise Control
Module, Turn Signal Cruise
Control Switches
23 Stoplamps
-- Stoplamp Switch
(Brake)
24 Not Used
25 English/Metric (S.E.O.)Fuse Rating
Description
26 Not Used
27 Not Used
28 CTSY Lamps
-- Vanity Mirrors,
I/P Compartment Lamp, I/S
Lighted Rearview Mirror, Dome
Lamp
29 Wiper
-- Wiper Switch
30 Turn Signal
-- Turn Signal Flasher
31 Not Used
32 Power Locks
-- Door Lock Relay,
Remote Keyless Entry Receiver
33 DRL MDL
-- Daytime Running
Lamp Module, (S.E.O.) Accessory
Switch
34 Not Used
35 Not Used

yellowblue
6-65
Underhood Electrical Center -- Passenger's Side
Some fuses are in a fuse block on the passenger's side of
the engine compartment.
Fuse Description
R/CMPT REL Remote Trunk Release, Back
-Up
Lamps, Remote Control Door
Lock Receiver
PCM BAT Powertrain Control Module
(PCM), Fuel Pump Relay, Fan
Cont #1 and #2 Relay
A/C CONT A/C CMPR Relay
TRANS Automatic Transaxle

yellowblue
6-66
Fuse Description
F/INJN Fuel Injectors
PCM IGN Mass Air Flow (MAF) Sensor
Heated Oxygen Sensor #1 and #2
Evaporative Emissions (EVAP)
Canister Purge Solenoid Valve
ELEK IGN Ignition Control (IC) Module
10 I/P Fuse Block
12 Passenger's Side Underhood
Electrical Center, IGN SYST
Relay, R/CMPT REL fuse, PCM
BAT fuse
13 FAN CONT #1 Relay
Relay Description
14 FUEL PUMP
15 A/C CMPR
16 FAN CONT #2
-- Secondary
Cooling Fan (Passenger's Side)
17 FAN CONT #1
-- Primary
Cooling Fan (Driver's Side)
18 IGN SYSTUnderhood Electrical Center
-- Driver's Side
Additional fuses are in a fuse block on the driver's side
of the engine compartment.

yellowblue
6-67
Fuse Description
FAN #3 FAN #3 Relay
PARK LPS Headlamp Switch
HORN Horn RelayFuse Description
ABS Anti
-Lock Brake System
11 Circuit Breaker C, Starter Relay,
STR WHL Control # 2, Power
Accessory #2, and Theft
-Deterrent
Relay
12 HD LPS
-- Circuit Breaker to
Headlamp Switch
13 ABS
-- ABS Relay
Relay Description
14 ABS
-- Anti-Lock Brake System
15 FAN #3
-- Secondary Cooling Fan
(Passenger's Side)
16 HORN

yellowblue
7-15 At Least Twice a Year
Restraint System Check
Make sure the safety belt reminder light and all your
belts, buckles, latch plates, retractors and anchorages are
working properly. Look for any other loose or damaged
safety belt system parts. If you see anything that might
keep a safety belt system from doing its job, have it
repaired. Have any torn or frayed safety belts replaced.
Also look for any opened or broken air bag coverings,
and have them repaired or replaced. (The air bag system
does not need regular maintenance.)
Wiper Blade Check
Inspect wiper blades for wear or cracking. Replace blade
inserts that appear worn or damaged or that streak or
miss areas of the windshield. Also see ªWiper Blades,
Cleaningº in the Index.
Weatherstrip Lubrication
Silicone grease on weatherstrips will make them last
longer, seal better, and not stick or squeak. Apply
silicone grease with a clean cloth. During very cold,
damp weather more frequent application may be
required. (See ªRecommended Fluids and Lubricantsº in
the Index.)Automatic Transaxle Check
Check the transaxle fluid level; add if needed. See
ªAutomatic Transaxle Fluidº in the Index. A fluid loss
may indicate a problem. Check the system and repair
if needed.
At Least Once a Year
Key Lock Cylinders Service
Lubricate the key lock cylinders with the lubricant
specified in Part D.
Body Lubrication Service
Lubricate all hinges and latches, including those for the
body doors, hood, secondary latch, pivots, spring
anchor, release pawl, rear compartment, glove box door,
console door and any folding seat hardware. Part D tells
you what to use. More frequent lubrication may be
required when exposed to a corrosive environment.