1999 BMW 528i engine

Downloaded from www.Manualslib.com manuals search engine
- -
Cylinder Head and valvetrain1
4 Bearing caps are marked with a code for location.
NOTE-
The camshaft caps are stamped with a code letter - "E for
the intake side and
'HA" for the exhaust side. Number code is
for position on head, with number
1 being the front bearing
cap.
CA UTIOI\C
Do not mix up camshaft bearing caps.
Install and evenly tighten down bearing cap nuts in
'I2 turn
steps starting at number
1.
Tightening torque
Camshaft bearing cap 14 Nrn (10 ft-lb)
4 Install BMW special tool 11 3 430 on camshaft.

Downloaded from www.Manualslib.com manuals search engine
1 16-50
/Cylinder Head and Valvetrain
4 Rotate camshafts until marker bores (insets) point upwards,
4 Secure camshafts in TDC position using BMW special tools:
Cylinders 5-8 Align camshafts w~th open-end 27 mm wrench so BMW
special tools fit on cylinder heads without gaps. Secure
11 2 242 11 2 446 I tool using number 8 cylinder spark plug hole.
CAUTION-
Do not damage the cylinder head. If necessary, machine
open-end wrench to
fit.
Timing chains and tensioners, installing (M62 engine)
4 Fit secondary sprocltets and chain to camshafts on right cyl-
inder head. Center slots in sprocltets to threaded bores in
end of camshafts (arrows).
. .

Downloaded from www.Manualslib.com manuals search engine
- -.
Cylinder Head and valvetrain1
Install exhaust camshaft bolts (arrows) finger tight.
Remove secondary timing chain tensioner
loclting tool.
< Fit secondary sprockets and chain to camshafts on left cylin-
der head. Center slots in sprocltets to threaded bores in end
of camshafts
(arrows).
Insert exhaust camshaft bolts (arrows) finger tight in exhaust
camshaft on left cylinder head.
Remove secondary timing chain tensioner locking tools from
chain tensioners.

Downloaded from www.Manualslib.com manuals search engine
ICylinder Head and Valvetrain -.
Rotate engine clockwise (arrow) from 45" before TDC to
TDC position.
Secure crankshaft in
TDC position with BMW special tool
11 2 300.
4 Fit sprocket with primary chain to intaite camshaft on right
cylinder head:
Press timing chain tensioner rail against timing chain
(white arrow) to check that fastener holes are centered in
sprocket slots (black arrows) when slack is removed from
timing chain.
If necessary, remove sprocket and reposition.
Fit sprocket with chain to intake camshaft
5-8 with long bores aligned centrally.
Install bolts (arrows) and finger tighten cylinder
head

Downloaded from www.Manualslib.com manuals search engine
Cylinder Head and valvetrain'
Fit sensor gear with mark (arrow) pointing upwards. Install
bolts and finger tighten.
4 Attach BMW special tool 11 7 380 to right cylinder head in
place of upper timing case cover.
Install BMW special tool
11 3 390 into 11 7 380.
Using BMW special tool 00 9 250, tighten adjustable ten-
sioner screw on
11 3 390 to 0.7 Nm (6.3 in-lb).
- T~ghten camshaft sprocket bolts in the following order:
1. Exhaust camshaft, left head.
2. Exhaust camshaft, right head.
3. Intake camshaft, left head.
4. Intake camshaft, right head.
Tightening torques Sprocket
to camshaft flange 15 Nm (I 1 ft-lb)
- Remove camshaft locking tools from both cylinder heads.
- Remove crankshaft locking tool.
4 lnstall oil lines to left and right cylinder heads.
- Remove adjustable timing chain tensioner tool and setup
block from right cylinder head.

Downloaded from www.Manualslib.com manuals search engine
11 6-54
Cylinder Head and Valvetrain
Replace primary timing chain tensioner O-ring (arrow) in
right cylinder head.
- lnstall right upper timing cover to engine:
Remove old gasket from right timing cover.
Clean gasket groove and install new gasket.
Apply Three Bond
12098sealant to joint between cylinder
head and timing cover. Install remaining timing cover bolts
finger tight.
lnstall left upper timing chain cover to engine:
Remove old gasket from right timing chain cover.
Clean gasket groove and install new gasket.
Insert lower cover timing chain cover retaining bolt (arrow)
to cover, then fit cover to cylinder head.
Apply Three Bond 12098 sealant to joint between cylinder
head and timing chain cover. lnstall upper timing cover
bolts finger tight.
4 Remove cylinder head cover sealing gaskets from right cyl-
inder head cover. lnstall BMW special tool 11
1 41 1 into gas-
ket groove of cylinder head cover.
lnstall right cylinder head cover with BMW special tool
11
1 41 1 to right cylinder head. Fit cylinder head cover retain-
ing nuts to cylinder head cover studs at cylinders
1 and 2
(first two cylinders on right cylinder head).
Tighten nuts uniformly in
'I2 turn steps.
NOTE-
BMW special tool 11 1 41 1 presses upper timing chain cover
to level of cylinder head.
Tightening torque Cylinder head cover nuts
10 Nm (7.5 n-lb)
- Tighten right upper timing cover retaining bolts in two passes.
Tightening torque
Timing chain cover to head
10 Nm (7.5 ft-lb)

Downloaded from www.Manualslib.com manuals search engine
11 6-55
Cvlinder Head and valvetrain1
4 Remove cylinder head cover sealing gasltets from left cylin-
der head cover. Install BMW special tool 11 1 412 into gasket
groove of cylinder head cover.
Install left cylinder head cover. Fit cylinder head cover re-
taining nuts to cylinder head cover studs at cylinders
5 and
6 (first two cylinders on left side cylinder bank).
* Tighten nuts uniformly in 'I? turn steps.
NOTE-
BMW special tool 11 1 4 12presses upper timing chain cover
to level of cylinder head.
Tightening torque Cylinder head cover
nuts 10 Nm (7.5 it-lb)
- Tighten left upper timing chain cover retaining bolts in two
passes.
Tightening torque
Timing chain cover to head
10 Nm (7.5 ft-lb)
- Remove cylinder head covers and remove BMW special
tools 11 4 41 11412 from cylinder head covers.
- Fit new gasket to cylinder head cover without strain.
- Apply Three Bond@ 1209 sealant to joints between cylinder
head and timing cover.
4 Malte sure half-moon cutouts (A) at rear of cylinder heads fit
correctly to cylinder head sealing surface. Apply Three
Bond@ 1209 sealant at corners of half-moon cutouts (B).
- Remainder of installation is reverse of removal.

Downloaded from www.Manualslib.com manuals search engine
1 16-56
Cylinder Head and Valvetrain
This section covers valve removal and reconditioning, includ-
ing valve guides, seats, springs, and valve stem oil seals.
Valves, leak test
To test the valves for leakage, the cylinder head must be dis-
assembled with camshafts and camshaft carriers removed.
With valve assemblies and spark plugs installed, place the
cylinder head on a workbench with the combustion chamber
facing upward. Fill each combustion chamber with a thin non-
flammable liquid. After fifteen minutes,
check the level of the
fluid. If the fluid level in any cylinder drops, that cylinder is not
sealing properly.
Valves, removing and installing
- Remove cylinder head as described in 113 Cylinder Head
Removal and Installation.
CAUTIOI\C
(M52 TU/M54 engines only) Do not let the hydraulic lifters
fall out as the camshaft carrier is removed. Special suction
cups are available from
BMW to hold the hydraulic lifters in
place during carrier removal.
* Hydraulic cam lifters should be stored m an uprfght po-
sition. If necessary, use a magnetic tool to
aidin remov-
al of the lifters.
- Remove valves using a valve spring compressor.
CAUTIOI\C
Label each valve assembly as it is removed so it can be in-
stalled in its original position.
-
- Remove and discard valve stem oil seals from valve guides.
See Valve stem oil seals later in this section.
- Valve installation is reverse of removal. Remove carbon de- - -
posits from the valves using a wire brush or wire wheel. -
-
Valve specifications are listed in Table c. Valve specifica-
tions.