1999 BMW 528i Suspension

Downloaded from www.Manualslib.com manuals search engine
330-1 9
Rear suspension1
Swing arm ball joint, replacing
- Raise rear end of car and remove wheel.
Make sure the car is firmly supported on jack stands de-
signed for the purpose. Place jack stands underneath struc-
tural chassis points. Do not place jack stands under
suspension
parts.
- Sport Wagon model: Support wheel bearing carrier from be-
low.
CA
UTION-
The shock absorberprevents the drive axle and wheel bear-
ing carrier from dropping too far. Supporting the wheel bear-
ing carrier before disconnecting the
shoclc absorber
mounting fastenerprevents damage to the brake hose, park-
ing
brake cable and drive axle CVjoints.
- Model with air shock absorbers: Detach air supply line from
shoclc absorber. Plug ports and lines to keep out dirt.
- Sport Wagon model: Remove shock absorber lower mount-
ing bolt.
4 Remove stabilizer bar link mounting nut (arrow). Press link
out of swing arm.
Model with air springs: Disable air supply pump by discon-
necting electrical plug before performing any repairs. Pump is
located beneath a cover under
the spare tire in the floor of the
carao
comoartment.
4 Model with air springs: Loosen compressed air pipes (ar-
rows) at air distribution assembly to release system pres.
sure.
WARNING-
Vehicle will lower when the air pipes are opened.
- Models with rear coil springs: Remove cargo compartment
floor carpet.

Downloaded from www.Manualslib.com manuals search engine
Rear Suspension
4 Models with coil springs: Working at top of spring, press cen-
ter cap down or pry upward to remove. If pushed down, re-
move from inside coil spring from under car.
4 Working from underneath, position BMW special tool 33 2
301
between 2nd and 3rd spring coil from bottom.
Make sure tool recess faces upward.
Working in cargo compartment, guide BMW special tool 33
2 304
from above and thread into special tool 33 2 301.
Working in cargo compartment, attach BMW special tools 33
2
302,33 2 303 and 33 2 305 to special tool 33 2 304.
Use special tool 33 2 306 to compress spring.
Tighten until lower spring coil lifts off spring seat on wheel
bearing carrier.
- - -
-

Downloaded from www.Manualslib.com manuals search engine
330-21
Rear Suspension
4 Remove outer mounting bolt (1) from swing arm. Pull swing
arm down.
Remove integral link
I swing arm metal bushing locating
bolt
(2). Remove integral link.
4 Press bushing out of wheel bearing carrier using BMW spe-
cial tools
33 4 191,33 4 192.33 4 193 and 33 3 333.

Downloaded from www.Manualslib.com manuals search engine
330-22
I Rear Suspension
s
4 If necessary, machine special tool 33 4 191 as shown.
NOTE-
Slotted end of special tool 33 4 191 points toward wheel
bearing carrier.
Press new bushing into wheel bearing carrier using BMW
special tools
33 4 191,33 4 192,33 4 194 and 33 3 333 until
bushing collar is flush with carrier (arrows).
- Install new snap ring
- Reassembly is reverse of disassembly
Use new self-locking nuts.
Tighten fasteners to final torque only after vehicle has
been lowered and suspension has settled.
Tightening torques Integral link to wheel bearing carrier 105
Nm (77
ft-lb)
Quick coupling screw to air shock 2
Nm (18 in-ib)
absorber
Road wheel to hub
120+lO Nm (89c7ft-ib)
Shock absorber to lower control arm 127 Nm (94 ft-lb)
Stabilizer link to swing arm 65
Nm (48
fl-lb)
Swing arm to wheel bearing carrier (C) 256 Nrn (189 ft-lb)
Upper rear control arm, removing and
installing (sedan models)
- Raise rear end of car and remove wheel.
WARNING-
Make sure the car is firmly supported on jack stands de-
signed for the purpose. Place jack stands underneath struc-
tural chassis points. Do not place
jaclc stands under
suspension parts.

Downloaded from www.Manualslib.com manuals search engine
330-23
Rear Suspension
Remove rear control arm:
Remove inner control arm bolt
(A).
Detach plastic wiring harness support (B).
* Remove outer control arm ball joint nut (C). Press ball joint
out of rear wheel bearing carrier.
Installation is reverse of removal, noting the following:
Always use new self-locking nuts.
Malte sure all threaded bolts, nuts and mating surfaces are
clean.
Inner control arm mounting bolt must thread to rear (bolt
head at front).
Tighten fasteners to final torque only afler vehicle has
been lowered and suspension has settled.
Have car professionally aligned when job is complete.
Tightening
torques
Control arm to subframe (M12) 110 Nm (81 ft-ib)
Control arm
ball joint to wheel bearing 142 Nm (105 ft-lb)
carrier
(M14)
Quick coupling screw to air shock absorber
2 Nm (18 in-lb)
Road wheel
to hub 120-flONm
(89 i7 ft-lb)
Upper rear control arm, removing and
installing (Sport Wagon models)
CAUTIOG
Disable air supply pump by disconnecting electrical plug be-
fore
perlorming any repairs. Pump is located beneath a cover
under the spare tire in the floor of the
carqo compartment.
- Raise rear end of car and remove wheel.
WARNING -
Make sure the car is firmly supported on jaclc stands de-
signed for the purpose.
Place jaclc stands underneath struc-
tural chassis points. Do not place jack stands under
suspension parts.
Models with rear coil springs: Remove cargo compartment
floor carpet.
Worlting at top of coil spring, press center cap down or pry
upward to remove. If pushed down, remove from inside coil
spring from under car.

Downloaded from www.Manualslib.com manuals search engine
330-24
Rear Suspension
4 Working from underneath, position BMW special tool 33 2
301 between 2nd and 3rd spring coil from bottom.
Make sure tool recess faces upward.
Working in cargo compartment, guide BMW special tool 33
2 304 from above and thread into special tool 33 2 301.
4 Working in cargo compartment, attach BMW special tools 33
2 302, 33 2 303 and 33 2 305 to special tool 33 2 304.
Use special tool 33
2 306 to compress spring.
Tighten until lower spring coil lifts off spring seat on wheel
bearing carrier.
4 Models with air springs: Loosen compressed air pipes (ar-
rows) at air distribution assembly to release system pres-
sure.
WARNING -
Vehicle will lower when the air pipes are opened. 1
- Support wheel bearing carrier from below.
CAUTION-
The shock absorber prevents the drive axle and wheel bear-
ing carrier from dropping too far. Supporting the wheel bear-
ing carrier before disconnecting the shock absorber
mounting iastenerprevents damage to the brake hose,
parl-
ino brake cable and drive axle CV ioints.
- Models with air shock absorbers: Detach air supply line from
shock absorber. Plug ports and lines to keep out dirt.
- Remove shoclc absorber lower mounting bolt

Downloaded from www.Manualslib.com manuals search engine
330-25
Rear Suspension
Remove rear control arm:
Remove inner control arm bolt
(A). Push shock absorber
out of the way to slide bolt out.
Detach plastic wiring harness support
(B).
Remove outer control arm ball joint nut (C). Press ball joint
out of rear wheel bearing carrier.
Installation is reverse of removal, noting the following:
* Always use new self-locking nuts.
Maite sure
ail threaded bolts, nuts and mating surfaces are
clean.
Inner control arm mounting bolt must thread to front
(bolt . head at rear).
Make sure long lower shock absorber bushing fits in hole
in suspension swing arm.
* Tighten fasteners to final torque only after vehicle has
been lowered and suspension has settled.
Have car professionally aligned when job is complete.
Tightening torques Control arm to
subframe (M12) 110 Nm (81 ft-ib)
Control arm ball joint to wheel bearing
142 Nm (105 ft-lb)
carrier
(M14)
Quick coupling screw to air shocit absorber
2 Nm (18 in-lb)
Road wheel to hub
Shoclc absorber to lower control arm 127 Nm (94 it-lb)
Upper front control arm (traction strut),
removing and installing
- Raise rear end of car and remove wheel.
WARNING-
Maice sure the car is firmly supported on jack stands de-
signed for the purpose. Place
jack stands underneath struc-
tural chassis points. Do not place jack stands under
< Mark location of inner control arm eccentric washer (rear toe

Downloaded from www.Manualslib.com manuals search engine
330-26
/ Rear Suspension
Remove inner control arm eccentric nut and bolt (A)
Remove control arm ball joint nut (6). Press ball joint out
of wheel bearing carrier.
Lifl out control arm.
Installation is reverse of removal, noting the following:
Use previously made
marks to install eccentric bolt and
nut.
Always use new self-locking nuts.
Tighten fasteners to final torque only after vehicle has
been lowered and suspension has settled.
0 Have car professionally aligned when job is complete.
Tightening
torques
Road wheel to hub 120klONm
(89 i7 ft-lb)
Upper front control arm (traction strut) to 60
Nm (44
ft-lb)
subframe (rear toe adjusting bolt)
Upper front control arm (traction strut) to wheel
65 Nm (48 ft-lb)
carrier
Rear axle assembly, removing and
installing (sedan models)
In case of damage to the subframe, or if a pressed-in bushing
is worn, remove
subframe by removing complete axle assem-
bly.
- Raise car and remove rear wheels.
WARNING-
Make sure the car is firmly supported on jack stands de-
signed for the purpose. Place jack stands underneath struc-
tural chassis points. Do not place
jack stands under
suspension parts.
- Remove exhaust system. See 180 Exhaust System
- Detach driveshaft from differential. See 260 Driveshaft.
- Remove brake caliper and brake disc. Hang brake caliper
aside with stiff wire. Do not disconnect brake fluid hose. See
340 Brakes.
- Remove lefl and right ABS sensors from wheel bearing car-
riers.
- Disconnect parking brake cable from brake shoe expander.
See 340 Brakes.
- Remove heat shield from above driveshaft.