1999 AUDI A8 display

01-176

Output Dia
gnostic Test Mode
(DTM
)
Press control valve -4- for auto. trans. -N218

Indicated on display:
Note: - Pressure Control valve -N218- is activated (clicks) To switch to next
actuator press key.
Electrical malfunctions will be stored in DTC memory, see DTC
table Page 01
-45

Output Dia
gnostic Test Mode
(DTM
)
Press reg. valve -5- for auto trans. -N233

"Pressure Regulating Valve -5- for Automatic Transmission -N233-" could
now be displayed erroneously due to a software error, even though it
does not exist. Disregard this display. Press button to switch to the next
actuator.
Output Dia
gnostic Test Mode
(DTM
)
Voltage supply for solenoid valves

Indicated on display:
Solenoid valves activated in position "P" are activated (click). Press key
to switch to the next actuator.
Can be disregarded.
-
Press key.
Pa
ge 15 of 18 Out
put Dia
gnostic Test Mode
(DTM
) (scan tool function 03
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.10

01-177

Function is unknown or cannot be carried out at the moment

Indicated on display
-
Pressing the key will terminate Output Diagnostic Test Mode.
Rapid data transfer
HELP
Select function XX

Indicated on display:
- To repeat Output Diagnostic Test Mode, switch ignition off and then on
again. Now select function 03 - Output Diagnostic Test Mode again.
Pa
ge 16 of 18 Out
put Dia
gnostic Test Mode
(DTM
) (scan tool function 03
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.10

01-178

DTC Memory, erasing (scan tool
function 05)


Requirement:

DTC memory checked page 01
-43
.

After DTC memory has been checked: Rapid data transfer
HELP
Select function XX

Indicated on display:
- Press keys 0 and 5. (With function 05 "Erase DTC memory" is entered)
Rapid data transfer
Q
05 Erase DTC memory

Indicated on display:
- Confirm entry with Q button.
WARNING!DTC memor
y was not checked

Indicated on display:
Note:
If the ignition was switched off e.g. between checking the DTC memory
and erasing DTC memory, the DTC memory is then not erased.
- Exactly follow the work sequence. The DTC memory must first be
checked.
Pa
ge 17 of 18 Out
put Dia
gnostic Test Mode
(DTM
) (scan tool function 03
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.10

01-179

Rapid data transfer DTC memor
y is erased!

Indicated on display:
(The DTC memory will be erased approx. 5 seconds. after the display
appears.)
The DTC memory is now erased.
Note:
Wait about 1 minute before checking the DTC memory again.
System cannot be checked!

Indicated on display:
1 Fault recognized !00811 3333System cannot be checked

Print out with printer switched on:
Transmission Control Module (TCM) -J217- was not given sufficient time
to recognize faults.
When the DTC memory is being checked, the following display should
appear: - Wait about 1 minute before checking the DTC memory again.
- After checking and erasing DTC memory, test drive the car and check
DTC memory again.
"No DTC recognized!"
Pa
ge 18 of 18 Out
put Dia
gnostic Test Mode
(DTM
) (scan tool function 03
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.10