1999 AUDI A4 wiring

24-56


If specified value is not obtained:
Electrical Wiring Diagrams, Troubleshooting & Component Locations
If specified value is obtained: - Connect multimeter for voltage measurement as follows.Central electronicsin driver-side footwell, left,
position 4
Terminal
Measure to
19 Engine Ground
(GND)
- Switch ignition on.

Specification: approx. battery voltage
- Check wire connections.
- Check the following wire connection for open circuit and short circuit to
Ground (GND) and B+: Central electronicsin driver-side footwell, left,
position 4
Terminal
VAG1598/31 test
box


Socket
Pa
ge 63 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-58
If specified values are not obtained:

- Repeat test at another terminal of fuse socket.
If specified values are not obtained again:

- Check wire connections.

Electrical Wiring Diagrams, Troubleshooting &
Component Locations If no malfunctions are detected:

- Replace Fuel Pump (FP) relay -J17-.

- Re-insert the fuses.
Pa
ge 66 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-64

Voltage supply for Mass Air Flow (MAF)
sensor, checking

Test requirements:

Fuse for Mass Air Flow (MAF) sensor OK

Electrical Wiring Diagrams, Troubleshooting &
Component Locations

Fuel Pump (FP) relay OK; checking Page 24
-52
.

Note:
Voltage is supplied to Mass Air Flow (MAF)
sensor from Fuel Pump (FP) relay.

- Disconnect connector from Mass Air Flow (MAF)
sensor.

- Connect multimeter for voltage measurement as follows.Harness connector
Terminal
Measure to
2 Engine Ground (GND)
Pa
ge 72 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-65
If specified value is not obtained:

- Check wire connection from terminal 2 of
connector to Fuel Pump (FP) relay via fuse for
open circuit and short circuit to Ground (GND):

Electrical Wiring Diagrams, Troubleshooting &
Component Locations
- Repair open circuit or short circuit if
necessary.

Note:
Ground (GND) from the ECM is present at terminal 3 of connector.
If specified value is not obtained: - Connect multimeter to terminal 2 and terminal 3 of connector for
voltage measurement.
- Operate starter briefly (engine can also start).

Specification: approx. battery voltage
- Check wire connections Page 24
-67
.
Pa
ge 74 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-67

Check wire connections for Mass Air Flow
(MF) sensor

Note:
Signal wire is also checked during wire test.

- Connect VAG1598/31 test box at wiring harness
to Engine Control Module (ECM), do not connect
ECM Page 24
-19
.

If wire connection is OK: - Check the following wire connections for open circuit and short circuit
to Ground (GND) and B+: Harness connector
Terminal
VAG1598/31 test box
Socket
3 27
4 53
5 29
- Repair open circuit or short circuit if necessary.
- Also check all wires for short circuit to each other.
- Replace Mass Air Flow (MAF) sensor -G70-.
Pa
ge 76 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1