1999 AUDI A4 display

24-113

Continuation
If the specified value in display group 037 and
038, display 3 or 4 is not obtained:

- Check exhaust system and catalytic converter
for leaks (check clamps and exhaust for
damage)

- If the difference of the values in measuring
blocks, display fields 3 (oxygen sensor
correction value) is to large (e.g.:+500 ms, -500
ms), it is possible that the oxygen sensor are
interchanged (mixed up).
If none of the causes are identified:

- Replace particular oxygen sensor "before"
catalytic converter.
Pa
ge 41 of 61 Ox
yg
en sensor control, checkin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.2

24-114

Oxygen sensor heater for oxygen
sensor, checking


Note:
The oxygen sensor heating circuit is monitored
by the On Board Diagnostic (OBD). Check DTC
memory Page 01-15
.

- Connect vehicle diagnostic, testing and
information system VAS5051 or VAG1551 scan
tool and select engine electronics control
module by entering address word "01" Page
01
-9 . When doing this the engine must be at
idle.
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select function "Read Measuring Value
Block" and confirm entry with -Q- button.
Read Measurin
g Value Block
Input display group number XXX

Indicated on display
- Press buttons -0-, -4- and -1- to select "display group number 041" and
confirm entry with -Q- button.
Read Measuring Value Block 41
1
2
3
4

Indicated on display
Pa
ge 42 of 61 Ox
yg
en sensor control, checkin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.2

24-115

- Adjust engine speed to approx: 3000 RPM

- Check resistance of oxygen sensor heater.

Display fields

1 2 3 4
Display Group 041: Oxygen sensor heater, Bank 1 (at idle speed)
Display
xxx kOhm
Htg.bC.ON
xxx kOhm
Htg.aC.ON
Indicates
Bank 1, Sensor 1
Status of
heater Bank 1, Sensor 2
Status of
heater
Range
Htg.bC.ON
Htg.bC.OFF
Htg.aC.ON
Htg.aC.OFF
Specified
value 0 - 0.5 kOhm
Htg.bC.ON/OFF
0 - 0.5 kOhm
Htg.aC.ON/OFF
Note
It can take a few minutes until
specification are obtained
It can take a few minutes until
specified values are obtained
- Press -C- button.

- Press buttons -0-, -4- and -2- to select "display
group number 042" and confirm entry with -Q-
button.
Pa
ge 43 of 61 Ox
yg
en sensor control, checkin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.2

24-116


Display fields

1 2 3 4
Display Group 042: Oxygen sensor heater, Bank 2 (at idle speed)
Display
xxx kOhm
Htg.bC.ON
xxx kOhm
Htg.aC.ON
Indicates
Bank 2, Sensor 1
Status of
heater Bank 2, Sensor 2
Status of
heater
Range
Htg.bC.ON
Htg.bC.OFF
Htg.aC.ON
Htg.aC.OFF
Specified
value 0 - 0.5 kOhm
Htg.bC.ON/OFF
0 - 0.5 kOhm
Htg.aC.ON/OFF
Note
It can take a few minutes until
specifications are obtained
It can take a few minutes until
specifications are obtained If the specification is not attained:

- Check voltage supply for oxygen sensor heater
Page 24
-117
.

- Check oxygen sensor signal wire and activation
Page 24
-122
.
Pa
ge 44 of 61 Ox
yg
en sensor control, checkin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.2

24-121
If the wiring is OK but the oxygen sensor heater
still has no Ground (GND) connection:

- Replace particular oxygen sensor.

- Display readiness code Page 01
-101
. The
readiness code must be generated if the DTC
memory was erased Page 01
-105
.
Pa
ge 49 of 61 Ox
yg
en sensor control, checkin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.2

24-122

Oxygen sensor signal wire and
activation, checking


Note:
The oxygen sensor signal is monitored by the
OBD system.

- Check DTC memory Page 01
-15
.

- If a oxygen sensor malfunction is displayed and
the oxygen sensor heater is OK, disconnect
harness connector for relevant oxygen sensor.
Component location of 4-pin harness connector
of oxygen sensor Page 24
-5 .

If the Specified value is not obtained, check oxygen sensor wiring: - Test voltage by connecting hand-held multimeter Fluke 83 (or
equivalent) (measuring range 2 V) between sockets 3 and 4 of
connector on wiring harness.
-
Switch ignition on. Specified value: 450 50 mV. Bank 1, Sensor 1 Page 24
-123
.
Bank 1, Sensor 2 Page 24
-125
.
Bank 2, Sensor 1 Page 24
-127
.
Bank 2, Sensor 2 Page 24
-129
.
Pa
ge 50 of 61 Ox
yg
en sensor control, checkin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.2

24-131
If no malfunction can be identified in the wiring:

- Replace Motronic Engine Control Module (ECM)
-J220 Page 24
-24
.

- Display readiness code Page 01
-101
. The
readiness code must be generated if the DTC
memory was erased Page 01
-105
.
Pa
ge 59 of 61 Ox
yg
en sensor control, checkin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.24.2