1999 AUDI A4 lock

Short to B+
_______________________
MIL Status:
MIL lights up immediately

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again

Engine Control Module (ECM) -
J192- faulty

- Replace and code engine control
module page 01
-265
erase DTC
memory and test drive check DTC
memory
Note:
If the malfunction "P1213 / 17621" and/or "P1214 / 17622" and/or "P1215 / 17623" is recognized by the engine control
module, the corresponding fuel injector is no longer triggered and the oxygen sensor control is blocked until ignition on.
Pa
ge 144 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

No
after test drive, check DTC memory
again

Engine Control Module (ECM) -
J192- faulty

- Replace and code engine control
module page 01
-265
erase DTC
memory and test drive check DTC
memory
Note:
If the malfunction "P1216 / 17624" and/or "P1217 / 17625" and/or "P1218 / 17626" is recognized by the engine control
module, the corresponding fuel injector is no longer triggered and the oxygen sensor control is blocked until ignition on.
Pa
ge 146 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-151

Note:
After function 04 is called up, the Engine Control
Module (ECM) carries out the following
operations:

Constant ignition timing point of 12 BTDC is
output in idle.

Digital idle speed control is blocked.
Evaporative emissions canister purge regulator
valve is closed.
A/C compressor is switched off.
EGR vacuum regulator solenoid valve is
closed
No coolant temperature correction-fixed value
of 80 C (176 F)

Learning values are relearned (idle and CO
content are adjusted automatically)
Pa
ge 207 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-167
Notes on display field 1:

The Engine Coolant Temperature (ECT) sensor is a temperature-dependent resistor. If the sensor signal is falsified by e.g.
dampness in the harness connection (effect as with resistors connected in parallel), this falsification can lie in a range that
is not recognized by the DTC memory.
If a malfunction relating to the Engine Coolant Temperature (ECT) sensor is stored, a coolant temperature of 20 C (68
F) is displayed in the measuring block at engine start. 10 C (50 F) is added to this for each minute of engine operation.
The maximum replacement value is 85 C (185 F).
Pa
ge 233 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-178
Test table display group 005 and/or display group 006 Display
fields Display on
VAG 1551
scan tool Malfunction cause
Malfunction repair
1, 2, 3, 4 Low oxygen
sensor learning
values
If first learning value in display field 1 is low, but
learning value in display fields 2, 3 and 4 normal:
oil dilution (large amount of fuel in the oil), fuel
injector leaks - Pull off cylinder block breather hose
and close
- If problem disappears after drive on
expressway and/or oil change
- Check fuel injector page 24
-29
If all four oxygen sensor learning values very low
overall:
- Fuel system pressure too high
- EVAP canister purge regulator valve -N80- open
continuously - Check system and residual pressure
page 24
-20

- Check -N80- page 24
-58
and/or
display group 009, display field 3
and/or display group 001, display field
2


Mass Air Flow (MAF) sensor -G70- faulty
Oxygen sensor (O2S) heating faulty or Heated
Oxygen Sensor (HO2S) dirty - Check MAF sensor -G70 page 24
-
81

- Check HO2S and O2S heating
page 24
-49
and/or display group 010,
display fields 1 and 2
Pa
ge 250 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-181
Display group 007 Display shows
Display/specified value
Designation/diagnose
Basic setting 7
1 2 3 4 0.0 6.0%1)
1 = Oxygen sensor (O2S) control (bank 1)

XXXX 2 = Oxygen sensor learning range display

XXXXXXXX 3 = Oxygen sensor learning requirement diagnosis

XXXXXXXX 4 = Oxygen sensor learning requirement display
Display group 008 Display shows
Display/specified value
Designation/diagnose
Basic setting 8
1 2 3 4 0.0 6.0%1)
1 = Oxygen sensor (O2S) control (bank 2)

XXXX 2 = Oxygen sensor learning range display

XXXXXXXX 3 = Oxygen sensor learning requirement diagnosis

XXXXXXXX 4 = Oxygen sensor learning requirement display
1) Evaluate tolerance range of the oxygen sensor control only at idle during "Basic Setting" function 04, since the EVAP
canister can also be controlled during "Read Measuring Value Block" function 08
Pa
ge 253 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

Oxygen sensor control can basically be evaluated both in "Basic Setting" function 04 as well as in "Read Measuring Value
Block" function 08 only after successful learning ( learning requirement display). Oxygen sensor control shows momentary control status. After successful learning, ( learning requirement display),
values vary around 0.0 6.0%. If the learning process (display field 4) is ended and no value around 0.0 6.0% is
obtained, observe display group 010, display fields 3 and/or 4 and check control behavior of the two heated oxygen
sensors. During this process, the display values must at times drop below 0.3 V and exceed 0.6 V, otherwise check
oxygen sensor heating and the heated oxygen sensor.
Pa
ge 255 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-187
Display group 009 Display shows
Specified display value
Designation
Basic setting 9
1 2 3 4 ... % 1 = Oxygen sensor control (bank 1)
... % 2 = Oxygen sensor control (bank 2)
0 - 99% 3 = Duty cycle (triggering)-EVAP canister purge regulator valve -N80-
0% and/or greater than 95% 4 = Throttle angle - at idle: 0%; at wide open throttle: > 95% Note:
The oxygen sensor control should always be evaluated only after successful learning ( learning requirement display, display
group 007 and/or 008, display field 4) in both "Basic Setting" function 04 and "Read Measuring Value Block" function 08.
Pa
ge 263 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1