1999 AUDI A4 display

01-185
Notes on display field 4
Display field 4 (learning requirement display) shows the learning range (display field 2) for which learning is required.
Requirement for learning:

No malfunction stored in DTC memory
Engine speed at idle 650-900 RPM and/or 1500-3000 RPM
Coolant temperature 80-110 C (176-230 F) (if learning does not start immediately after this requirement, step on the
throttle).
Learning is prohibited:

With uneven idle (hunting), during acceleration, at wide open throttle
If malfunctions are stored in the DTC memory (not with sporadic malfunctions)
If differences of 9% are obtained between the richest and leanest oxygen sensor learning value of one display group. If a
9% difference is obtained, continued learning of the learning range involved is discontinued. The learning requirement
display of this learning range can not be 1 display groups 005 and/or 006.
Learning starts 20 sec. after initiation of "Basic Setting" function 04 and/or 2 to 4 min. after each start at a which the coolant
temperature is less than 40 C (104 F). The following listing shows when the request for new learning (learning requirement) is forced:
Pa
ge 260 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

During "Basic Setting" function 04 with VAG 1551 scan tool and/or each time the DTC memory is erased, all learning
requirement displays are set to 0 in order to force new learning of the oxygen sensor learning values after the shop visit.
At each start, coolant temperature less than 40 C (104 F), the learning requirement is forced in all learning ranges. If there is a large learning value deviation (from the stored learning value to the newly learned value) in the learning
process, all learning requirement displays are reset to 0.
If there is successful learning, the learning requirement values of the respective learning ranges (display field 2) are set to 1.
Pa
ge 261 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-186

X
X
X
X
X
X
X
X
Meaning of 8-digit oxygen sensor learning requirement display

1 = Idle (bank 1)

2 = Idle (bank 2)

3 = Partial throttle 1 (bank 1)

4 = Partial throttle 1 (bank 2)

5 = Partial throttle 2 (bank 1)

6 = Partial throttle 2 (bank 2)

7 = Partial throttle 3 (bank 1)

8 = Partial throttle 3 (bank 2) Display value "0" = Request for new learning.
Display value "1" = Learning process ended.
Pa
ge 262 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-187
Display group 009 Display shows
Specified display value
Designation
Basic setting 9
1 2 3 4 ... % 1 = Oxygen sensor control (bank 1)
... % 2 = Oxygen sensor control (bank 2)
0 - 99% 3 = Duty cycle (triggering)-EVAP canister purge regulator valve -N80-
0% and/or greater than 95% 4 = Throttle angle - at idle: 0%; at wide open throttle: > 95% Note:
The oxygen sensor control should always be evaluated only after successful learning ( learning requirement display, display
group 007 and/or 008, display field 4) in both "Basic Setting" function 04 and "Read Measuring Value Block" function 08.
Pa
ge 263 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-188
Test table display group 009 Display fields
Display on VAG 1551 scan tool
Malfunction cause
Malfunction repair
1 -
- Display group 007, display field 1
2 -
- Display group 008, display field 13 -
- Note4 -
- Display group 003, display field 3
Notes on display field 3:

The evaporative emissions valve (EVAP canister valve) is closed during the learning process.
The effect of the EVAP canister can be evaluated by comparing the display value during "Basic setting" (EVAP canister
completely closed: 99%) and during "Read Measuring Value Block" (EVAP canister valve completely open: 0%).
You can switch back and forth between "Basic Setting" function 04 and "Read Measuring Value Block" function 08 by
pressing buttons -1- and -3- on VAG 1551 scan tool.
Pa
ge 264 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-189
Display group 010 Display
shows Specified display value
Designation
Basic setting
10
1 2 3 4 Difference between display values 1 and 2
less than 8% 1 = Total of oxygen sensor control (bank 1) and momentary
oxygen sensor learning value (bank 1)
2 = Total of oxygen sensor control (bank 2) and momentary
oxygen sensor learning value (bank 2)

At times greater than 0.6 V and/or less than
0.3 V (display must fluctuate) 3 = Voltage signal-bank 1 heated oxygen sensor 1
4 = Voltage signal-bank 2 heated oxygen sensor 1 Note:
The total of the oxygen sensor control and oxygen sensor learning value shows the total effect of the oxygen sensor control.
Bank differences can be evaluated directly by comparing display field 1 with display field 2.
Pa
ge 265 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-190
Test table display group 010 Display
fields Display on VAG 1551 scan tool
Malfunction cause
Malfunction repair
1/2 Difference between display value
1 (bank 1) and display value 2
(bank 2) greater than 8%
Spark plug faultyIntake air leak on one side Fuel injectors faulty - Repair cause
- Check DTC memory page 01
-13

and/or check fuel injectors page 24-
29


Heated Oxygen Sensor
(HO2S) faulty (dirty) - Check DTC memory page 01
-13

and/or display fields 3 and 4

Mechanical engine basic
setting (valve/camshaft
timing) not OK
Repair Manual, 2.8 Liter V6 2V
Engine Mechanical, Engine Code(s): AFC, Repair Group 13
- Check valve/camshaft timing
Pa
ge 266 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-191

Display
fields Display on VAG 1551 scan tool
Malfunction cause
Malfunction repair
3/4 Display does not fluctuate-constant
between 0.0 - 0.3 V and/or between
0.6 - 0.9 V
Fuel injector faulty- Check fuel injectors page 24
-29

Spark plug faultyLarge intake air leak Engine Coolant Temperature
(ECT) sensor -G62- faulty EVAP canister purge
regulator valve -N80- - Check spark plug
- Repair cause
- Check DTC memory page 01
-13

and/or check -G62-
- Check using output diagnostic test
mode page 01
-145
and/or check -
N80-

Heated Oxygen Sensor
(HO2S) -G39- faulty or dirty Oxygen Sensor (O2S) heater
-Z19- does not function - Check DTC memory page 01
-13

and/or check -G39-
- Check -Z19- page 24
-49

Fuel system pressure too
high or too low - Check fuel pressure regulator and
residual pressure page 24
-20


Constant 2.550 V Short to positive (B+) through:
Heated Oxygen Sensor
(HO2S) -G39- wiring Engine Control Module
(ECM) -J192- - Check -G39- page 24
-49Pa
ge 267 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1