1999 AUDI A4 display

-
Press button. Rapid data transfer
HELP
Select function XX

Indicated on display
Pa
ge 22 of 91 A/C s
ystem, On Board Dia
gnostic
(OBD
)
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.HA01.01.1

01-18

Check DTC Memory (function 02)


- Press buttons -0- and -8- to insert "AC/Heating
Electronics" address word 08 and advance
program until "Select function XX" appears on
display page01
-17
.

- Switch printer on by pressing PRINT button
(indicator lamp in button comes on). Rapid data transfer
HELP
Select function XX

Indicated on display (function selection)
- Press buttons -0- and -2- to select "Check DTC Memory" function 02.
Rapid data transfer
Q
02 - Check DTC Memor
y

Indicated on display
- Press -Q- button to confirm input.
Rapid data transfer
Q
X DTC reco
gnized

Number of stored DTCs is displayed
-
Press button.
Rapid data transfer
Q
No DTC reco
gnized

If "No DTC recognized" is displayed, the program returns to the starting
position after button is pressed page 01
-20
.
Notes:
-
Press button.
If the printer is switched on, stored DTCs are displayed and printed
Pa
ge 23 of 91 A/C s
ystem, On Board Dia
gnostic
(OBD
)
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.HA01.01.1

out in sequence. If the printer is switched off, the button must be pressed in order to
display the next DTC.
Pa
ge 24 of 91 A/C s
ystem, On Board Dia
gnostic
(OBD
)
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.HA01.01.1

01-19

If DTC are displayed:

- Refer to DTC table and check and repair as
instructed page 01
-22
.

- Operate A/C system and check DTC memory
(function 02) to confirm repair.

- Erase DTC memory (function 05).

- Confirm A/C control head -E87- coding (function
01), and if necessary code -E87- (function 07).

- Perform basic setting (function 04).

- Check DTC memory (function 02), if
malfunctions are stored, erase DTC memory
(function 05).

- VAG1551 Scan Tool (ST) can be returned to the
function mode by pressing the button. Rapid data transfer
HELP
Select function XX

Indicated on display (function selection)
- End output (function 06) page 01
-56
.
- Switch ignition off and disconnect VAG1551 Scan Tool (ST) from Data
Link Connector (DLC).
Pa
ge 25 of 91 A/C s
ystem, On Board Dia
gnostic
(OBD
)
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.HA01.01.1

01-20

If no DTC are displayed and A/C system
complaints exist (e.g. compressor does not
run or only occasionally, system control
unsatisfactory, speed of fresh air blower
cannot be regulated etc.):

- Read measuring value block (function 08).

- Perform Output Diagnostic Test Mode (DTM)
(function 03).

- Check A/C system cooling performance page
87
-213
.

- VAG1551 Scan Tool (ST) can be returned to the
function mode by pressing the button. Rapid data transfer
HELP
Select function XX

Indicated on display (function selection)
- End output (function 06) page 01
-56
.
- Switch ignition off and disconnect VAG1551 Scan Tool (ST) from Data
Link Connector (DLC).
Pa
ge 26 of 91 A/C s
ystem, On Board Dia
gnostic
(OBD
)
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.HA01.01.1

01-21

Notes:

1997 If A/C control head -E87- is unable to
determine the duration of time when ignition is
off ("standing time"), DTC 01206 "signal for time
span ignition off" is loaded into memory. The
A/C control head will then default to a standing
time greater than 4 hours. The actual measured
values of the outside temperature sensor are
then used as instantaneous outside and engine
temperature inputs for A/C system control.
When the "heating" mode is selected under
these conditions, fresh air blower -V2- has a
delayed start (even when the actual standing
time is less than 4 hours and the engine is
warm) page 01
-86
, Read Measuring Value
Block. The outside air temperature display -
G106- may also indicate incorrect outside
temperature values.

If both display fields of the A/C control head do
not light with ignition switched on check control
head coding Page 01
-57
.
Pa
ge 27 of 91 A/C s
ystem, On Board Dia
gnostic
(OBD
)
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.HA01.01.1

01-22
Diagnostic Trouble Code (DTC) table

Notes:

DTC changes affecting m.y. 1997 vehicles page 01
-38
.
Diagnostic Trouble Codes (DTC) recognized by A/C control head -E87- and displayed on VAG1551 Scan Tool (ST)
starting on page 01
-24
.
If malfunctions occur only occasionally or if the DTC memory was not erased after repairs, such DTC are displayed as
"sporadic faults." (The contents of DTC memory is retained until erased, "permanent memory").
DTCs and flash codes (only for specific components) appear only in the printout in operating mode -1-, (Rapid data
transfer).
In addition to displayed DTC and affected component descriptions, malfunction cause information is listed in the table
below the DTC code.
After performing repairs and operating the A/C system, DTC memory must always be checked again to confirm the repair.
Before replacing a suspected malfunctioning component, check all appropriate wiring, connections, harness connectors
and Ground (GND) connections.
When checking for the cause of sporadic faults, check all plug connections and wiring between A/C control head -E87-
and any component recognized as being inoperative using wiring diagram.
After replacing AC/heating system components, always perform basic setting (function 04), check DTC memory (function
Pa
ge 28 of 91 A/C s
ystem, On Board Dia
gnostic
(OBD
)
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.HA01.01.1

01-23
Notes

If 22 C (72 F) is always displayed after switching ignition off and on, regardless of last setting, check power supply
(terminal 30) to A/C control head -E87- using wiring diagram. If a malfunction is recognized at an air/temperature distribution flap motor potentiometer, air distribution can be altered by
pressing buttons on A/C control head -E87-.
To switch display from C (Celsius) to F (Fahrenheit)(and vice versa), press "Temperature +" button while holding
"recirculating air" button. If no DTC are displayed and air conditioning system complaints exist (e.g. compressor does not run or only occasionally,
system control unsatisfactory, speed of fresh air blower cannot be regulated etc.), perform function 03 "Output Diagnostic
Test Mode (DTM)" and 08 "Read Measuring Value block."
Pa
ge 30 of 91 A/C s
ystem, On Board Dia
gnostic
(OBD
)
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.HA01.01.1