1998 VOLVO S90 seats

1998 Volvo S90
The warning lights described on pages 18 and 19 should never stay on whe\
n driving

When the ignition key is turned on, and before the engine starts, all of\
the warning lights should be on
to test the function of the bulbs. Should a light not go off after the e\
ngine has started, the system
indicated should be inspected. However, the parking brake reminder light\
will not go off until the
parking brake is fully released.
Generator warning
light

If the light comes on while the
engine is running, have the
charging system checked.

Malfunction
indicator lamp

If the lamp comes on (or stays
on after the vehicle has started),
the engine diagnostic system
has detected a possible fault in
the emission control system.
Although driveability may not
be affected, see an authorized
Volvo retailer as soon as
possible for inspection.

NOTE:If the fuel filler cap is
not closed tightly or if the
engine is running when the car
is refueled, the Malfunction
Indicator Lamp may indicate a
fault. Use only Volvo original
or approved fuel filler caps.
Oil pressure warning
light

If the light comes on while
driving, stop the car and then s
If the light stays on after restart,
have the car towed to the
nearest authorized Volvo
retailer. After hard driving, the
light may come on occasionally
when the engine is idling. This
is normal, provided it goes off
when the engine speed is
increased.

Parking brake
reminder light

This light will be on when the
parking brake (hand brake) is
applied. The parking brake
lever is situated between the
front seats. Canadian models
are equipped with this warning
light:

Brake failure
warning light

If the light comes on while
driving or braking, stop
immediately, open the hood and
check the brake fluid level in the
reservoir. See page 114 for
reservoir position.
Canadian models are equipped
with this warning light:


WARNING!
If the level is below the MIN
mark in either section of the
reservoir: DO NOT DRIVE.
Tow the car to a Volvo
retailer and have the brake
system checked and any
leakage repaired.
Warning lights (cont.) pg. 19
file:///K|/ownersdocs/1998/1998_SV90/98S90_017.htm (2 of 7)12/30/2006 \
1:52:36 PM

1998 Volvo S90
Chapter 2 - (cont.)
Heated front seats
pg. 28


Heated front seats (certain models)

The heated front seats can be switched on and off
as required. When switched on, the system senses
the ambient temperature and regulates the level of
heat applied. When the optimum temperature is
reached, the heating is switched off automatically.
While driving, the passenger seat heating should
be switched off when the seat is not occupied.
Electrically operated windows pg. 29


Electrically-operated windows

The electrically operated windows are controlled
by switches from the driver's armrest as shown in



Cut-out switch for rear-door windows

If the car is equipped with rear door power
windows, this function can be disabled by a
switch located on the driver's armrest. This switch
file:///K|/ownersdocs/1998/1998_SV90/98S90_028.htm (1 of 3)12/30/2006 \
1:52:38 PM

1998 Volvo S90
the above illustration.
The starting (ignition) switches must be ON
(position II) for the electrically operated windows
to function. The window is lowered if the rear part
of the switch is pressed and raised if the front part
of the switch is pressed.
NOTE: Driver's window only (AUTO): The
window can be opened completely by pressing the
rear part of the switch lightly and releasing it
immediately. The window can be stopped by
pressing the button again. If the button is held
down, the window will be lowered until the button
is released.
WARNING!Remove the starting (ignition)
key when children are left unattended in the
vehicle.
Make sure that children's hands are clear
before raising the windows. is positioned 90° in relation to the other switches.
ON The rear door windows can be raised or
lowered with the respective door switch as well as
the switch on the driver's door.
OFF The rear door windows cannot be raised or
lowered with the respective door switch but
instead only with the corresponding switch on the
driver's door.

NOTE: The power window motors have an
overload protecting circuit breaker which is
activated when an object blocks a window.
Should this occur, remove the object and wait 20
seconds for the circuit breaker to reset. The power
windows should then function.
Parking brake, Cigarette lighter, Ashtrays pg. 30


Parking brake (hand brake)

The lever is situated between
the front seats. The brake is
applied to the rear wheels.


Cigarette lighter/ashtrays

To operate, depress the knob
fully. When the knob
automatically releases, the
cigarette lighter is ready for use.
The starting (ignition) switch
must be switched on (to position
I or II) for the cigarette lighter
to function.

"OBD II"

A connector for on-board
diagnostics ("OBD II") is located
to the right of the parking brake.
This connector is intended for
use by authorized service
technicians only.
file:///K|/ownersdocs/1998/1998_SV90/98S90_028.htm (2 of 3)12/30/2006 \
1:52:38 PM

1998 Volvo S90
Chapter 3 - Body and interior
pg. 31
Body and
interior
The seats,
doors, sun
roof, mirrors,
etc. are
described on
the following
pages.
Keys, Doors and Locks pg. 32

Remote keyless entry system pg. 32
Front seats pg. 34
Rear/side view mirrors, Vanity mirror pg. 35
Interior light, Rear reading lights pg. 36
Child safety locks, Trunk lid pg. 37
Passenger compartment storage spaces pg. 38
Hood pg. 39
Trunk light, spare tire, jack (sedan) pg. 40
Wagon tailgate/child safety lock pg. 41
Concealed storage bins, Folding rear seat (wagon) pg. 42
Removing seat cushions, Securing cargo (wagon) pg. 44
Cargo space lighting, spare tire, jack (wagon) pg. 45
Cargo space - loading pg. 46
Cargo barrier pg. 47
Luggage cover pg. 48
Sun roof pg. 49
Long load storage pg. 50
Alarm pg. 51
Keys, Doors and Locks pg. 32
file:///K|/ownersdocs/1998/1998_SV90/98S90_031.htm (1 of 6)12/30/2006 \
1:52:39 PM

1998 Volvo S90


Remote keyless entry
system

As an option, your car can be
equipped with a remote
control transmitter. This
transmitter uses a radio
frequency which will allow
"keyless" entry into the
passenger compartment or the
trunk. You will be supplied
with two coded key ring
transmitters, which will
enable you to lock/unlock all
doors and the trunk/tailgate
from a distance of 10-15 feet
(3-5 meters).

To lock :
Press the lock button once to
lock all doors and trunk/
tailgate.

To unlock :
Press the unlock button once
to unlock the driver's door
only.
Press the unlock button again
(within 10 seconds) to unlock
all doors and trunk/tailgate.


Aim the base of the remote control unit at
the car to get the best range.

On vehicles equipped with an alarm, the
alarm will also be activated/deactivated by
this system.
As an extra security precaution in certain
situations (valet parking, etc.), Volvo
recommends that the transmitter not be
included when the keys are given to
anyone. The service key can be used
instead. If one of the transmitters is
misplaced, contact the nearest authorized
Volvo retailer for assistance.

Batteries

The remote transmitter is powered by 2
three-volt batteries, type CR 1220. If three
short signals are audible from the
transmitter each time you lock/unlock the
car, this indicates that the batteries are
weak.
Replacement: Remove the battery cover
on the back of the transmitter with a coin.
Replace the batteries. Reinstall the cover,
making sure it is secured tightly to help
protect the transmitter. New transmitters

If you purchase additional
transmitters, they must be
programmed to function with
your remote keyless entry
system. Please refer to page 49
for instructions.

This device complies with
FCC rules Part 15.
Operations is subject to the
following two conditions:
(1) This device may not
cause harmful interference
and (2) this device must
accept any interference that
may be received, including
interference that may cause
undesired operation.

WARNING! Volvo does
not recommend using the
transmitter to lock the doors
from inside the car. On cars
equipped with an alarm, the
alarm would be activated
and would sound when one
of the doors is opened. The
doors must not be locked
using the remote transmitter
while the vehicle is
occupied. In case of an
accident, this may hinder
rapid access to the
occupants of the vehicle.
The alarm will also sound
on models equipped with
this feature.
Front seats pg. 33
file:///K|/ownersdocs/1998/1998_SV90/98S90_031.htm (3 of 6)12/30/2006 \
1:52:39 PM

1998 Volvo S90
Electrically operated front seats

The front seats are electrically operated.
Using the switches on the sides of the seats
you can adjust:
-the height of the seat (rear)
-the height of the seat (front)
-the forward-backward movement
-the backrest tilt

NOTE:The electrically operated front
seats have an overload protector which
engages if an object blocks either of the
seats. If this happens remove the object
and wait 20 seconds. The overload
protector should then have cooled down
and the power seats should function
normally. Passenger's seat (option)



The STOP button (passenger
seat only) overrides the other
controls. To stop movement
of the seat, press and release
the STOP button. Press the
button again to reactivate the
seat controls.
A Seat front (raise/lower)
B Forward -rearward
C Seat rear (raise/lower)
D Backrest tilt
WARNING! Do not
adjust the seat while
driving. The seat should
be adjusted so that the
brake pedal can be
depressed fully. In
addition, position the seat
as far rearward as comfort
and control allow. The
seat rails on the floor must
not be obstructed in any
way when the seat is
moved.

Driver's seat



Movement of the driver's seat
can be STOPPED at any time
by pressing any button on the
seat's control panel.

WARNING!The driver's
seat is operable with the
ignition OFF.
Therefore, children should
never be left unattended in
the car.



Programming the memory

Three seat positions can be
programmed. To program a
seat position:
1. Adjust the seat to the
desired position.
2. Depress the MEM button.
3. Press button 1 to program
the current position of the
seat.
Buttons 2 and 3 can be
programmed in the same way
for two additional seat
positions. To move the seat to
a programmed position,
depress button 1, 2 or 3 until
the seat stops. If the button is
released before the seat has
the reached the programmed
position, it will stop as a
safety precaution.
Rear-/side-view mirrors, Vanity mirrors pg. 35
file:///K|/ownersdocs/1998/1998_SV90/98S90_031.htm (4 of 6)12/30/2006 \
1:52:39 PM

1998 Volvo S90
swing the cushion up and toward the
back of the front seats.
Move the backrest release lever rearward
and fold the backrest down.
When the backrest is raised, the outboard
head restraints return to their normal
position and must be raised manually if
required.
The backrest must lock into place. The
red lock indicator will not be visible if
the seat has locked into place
correctly. seat is returned to normal position. WARNING! When the rear seat is
folded down, do not place heavy
objects against the backs of the front
seats. This places a severe strain on
the folded down backrest of the rear
seat. Be sure to secure cargo. Cargo
must not be stacked higher than the
top of seatbacks. This will reduce the
possibility of luggage, etc. becoming
projectiles during sudden maneuvers,
rapid braking or an accident. The red
lock indicator is visible when the
backrest is NOT locked in position
and not visible when the backrest is
correctly locked in place. When the
backrest is in the upright position, it
must always be correctly locked in
place.
Removing seat cushions, Tool box, Securing cargo (wagon) pg. 44

Lift the seat cushion part way and
remove the seat.

Removing seat cushions

The seat cushion can be easily removed
to provide a slightly larger cargo storage
area. To remove, lift the seat cushion out
of the hinges.

Tool box

Tool box

The tool box can be released by turning
the catch.

WARNING! Do not place extremely
heavy articles the front seats, as the
backrest which is folded down is then
placed under severe strain.
Be sure to secure cargo. Hard and sharp
articles could otherwise damage the
frontseat backrest and/or cause injury to
passengers in the event of rapid braking
or a collision.
Always secure cargo

Securing cargo

As a safety precaution, the cargo space
is equipped with six eyelets to which
straps can be attached to secure
luggage.

file:///K|/ownersdocs/1998/1998_SV90/98S90_042.htm (2 of 4)12/30/2006 \
1:52:40 PM

1998 Volvo S90
(check when tires are cold). items and others are checked at
the standard Maintenance
Service intervals.

NOTE: Since using (D)rive
improves fuel economy, it
should be used as often as
possible.
Starting the engine pg. 57
Starting and stopping a
car equipped with
automatic transmission

1 Fasten the seat belt.
WARNING! Before
starting, check that the seat
is adjusted properly. Make
sure the brake pedal can be
depressed completely. Move
the seat closer if necessary.
Refer to section "Front
seats".

2 Apply the parking brake, if
not already set. The gear
selector is locked in the (P)ark
position (SHIFTLOCK).

3Without touching the
accelerator pedal ,turn the
ignition key to the starting
position. Allow the starter to
operate for 5-10 seconds.
Release the key as soon as the
engine starts. If the engine fails
to start, repeat step 3.

5 Select desired gear. The gear
engages after a slight delay,
especially noticeable when
selecting R.
CAUTION: Engine should
be idling; never accelerate
until after you feel the gear
engage! Too rapid
acceleration immediately
after selecting a gear will
cause harsh engagement and
premature transmission
wear.

NOTE:Your car is equipped
with a KEYLOCK system.
When the engine is switched
off, the gear selector must be in
the (P)ark position before the
key can be removed from the
ignition switch.

Engine warm-up - initial
driving procedure

Engines in vehicles driven short
distances are subject to
abnormally rapid wear because
the engine never reaches normal
operating temperature. It is
therefore beneficial to reach
normal operating temperature as
soon as possible. This is best
achieved by driving with a light
foot on the accelerator pedal for
a few minutes after starting,
rather than prolonged idling.

B6304 S Engine


This engine features hydraulic
valve lifters which means that
valve clearance is adjusted
automatically. It is possible that
the valve lifters will produce a
ticking sound for the first few
seconds after the engine is
started, while the oil pressure is
increasing.
If the car has not been used for a
long period of time, this ticking
sound may last for up to 15
minutes. This is entirely normal.
file:///K|/ownersdocs/1998/1998_SV90/98S90_053.htm (5 of 6)12/30/2006 \
1:52:41 PM