1998 VOLKSWAGEN BORA light

Downloaded from www.Manualslib.com manuals search engine 01-20



Parking brake indicator light -K14-

Electrical Wiring Diagrams,
Troubleshooting & Component Locations
binder
Vehicles with ABS/EDL
Malfunction: Vehicle has no EDL
function
For this complaint a possible cause may be
the brake light switch -F- is incorrectly
adjusted. Adjusting brake light switch
Page 01
-131 .
Another possible cause may be the brake
light switch -F- is not functioning. The
function can be checked in Read measured
value block Page 01
-61 , display group
number 003.
If the parking brake indicator light -K14-
-3- does not go out after switching the
ignition on, the malfunction may be:
-a- The parking brake is applied.
-b- The parking brake warning light switch -
F9- for the parking brake indicator light -
K14- is faulty or incorrectly adjusted.
-c- There is a wire routing malfunction.
Стр. 14из 14 Electrical/electronic components and locations

Downloaded from www.Manualslib.com manuals search engine 01-22



Test requirements

The tires installed to all wheels must be of
the same (approved) size; tires inflated to
prescribed pressure.

Mechanical/hydraulic parts of the brake
system including brake light switch and
brake lights OK.

Hydraulic lines and connections not leaking
(visual check of hydraulic unit, brake
calipers, wheel cylinders, tandem master
brake cylinder).

Wheel bearings and wheel bearing play
OK.

ABS control module (w/EDL) -J104- is
correctly bolted to hydraulic unit -N55-.

Connector on ABS control module (w/EDL)
-J104- correctly plugged-in (retainer is
engaged).

Check contacts of ABS components for
damage and correct seating.

All fuses OK according to wiring diagram
(remove fuse from fuse holder to check).

Supply voltage OK (at least 10.0 V).
Стр. 2из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program

Downloaded from www.Manualslib.com manuals search engine 01-24


The PRINT key is used for switching on the
printer (warning lamp in key comes on).

- Switch ignition on.

- Switch on printer with Print key (indicator lamp in
key lights up).

- Press key -1- for "Rapid data transfer" operating
mode.
Rapid data transfer HELP
Enter address word XX Indicated on display
- Press keys -0- and -3-; 03 inputs the address
word of the vehicle system to be tested "Brake
electronics".
Rapid data transfer Q
03 - Brake electronics Indicated on display
- Confirm input with Q key.
1J0 907 379 D ABS 20 IE CAN 0001
Coding 03604 WSC XXXXX
Display shows e.g.
Displayed is:
e.g. (1J0 907 379 D)
Allocation of control module see Parts catalog
Electrical Wiring Diagrams, Troubleshooting &
Component Locations binder
The control module identification number.
System designation (ABS 20 IE)
Data BUS present. (CAN)
Стр. 4из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program

Downloaded from www.Manualslib.com manuals search engine 01-30


Automatic test sequence
The automatic test sequence checks all the
Diagnostic Trouble Code (DTC) memories
of the control modules.

- Switch ignition on.
V.A.G - On Board Diagnostic HELP
1 - Ra
pid data transfer1)
2 - Blink code output1)
Indicated on display
1) Is displayed alternately
- Press key -1- for "Rapid data transfer"
operating mode.
- Switch on printer with the Print key
(indicator lamp in key lights up).
Rapid data transfer HELP
Select function XX Indicated on display
- Press key -0- twice; 00 enters "Automatic
test sequence" function.
- Confirm entry with Q key.
1J0 907 379 D ABS 20 IE CAN0001
Coding 03604 WSC XXXXX
The V.A.G 1551 Scan Tool display will
show the control module identification, e.g.:
Thereafter all control module
identifications with eventual DTC
memory entries are displayed
Стр. 10из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program

Downloaded from www.Manualslib.com manuals search engine 01-52


V.A.G 1551
print-out Possible cause
Repair
01312
Drive train data
bus faulty
1)


or:
ABS control module (w/EDL) -
J104- incorrectly coded

Engine control module
incorrectly coded
Repair group 01 for relevant
engine code - Check ABS control module
(w/EDL) -J104- coding Page 01
-
58
- Check engine control module
coding

Open circuit, short to positive or
Ground in the wiring - Check wiring and connections
using wiring diagram

- Perform electrical checks Page
01-102
Drive train data
bus faulty
1)

Sporadic
Ignition/starter switch turned
too slowly - Erase DTC memory Page 01-56
- No further measures required
- Inform customer
1) The DTC "Drive train data bus" will not cause the ABS warning light -K47- or warning light for
brake system -K118- to light up. The ABS function is retained over the complete range.
Стр. 32из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program

Downloaded from www.Manualslib.com manuals search engine 01-57


Warning!
DTC memor
y was not interrogated.
Indicated on display
Note:
Adhere exactly to test sequence: First
check DTC memory, then erase
2. Ending output
- Press keys -0- and -6-, to end output.
Rapid data transfer Q
06 - End output Indicated on display
- Confirm input with Q key.
Rapid data transfer HELP
Select function XX Indicated on display
ABS warning light -K47- and warning light
for brake system -K118- must go out after
approx. 2 seconds. - Switch ignition off.
- Disconnect V.A.G 1551 Scan Tool at
Data Link Connector (DLC).
- Switch ignition on.
Стр. 37из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program

Downloaded from www.Manualslib.com manuals search engine 01-58


ABS control module, coding

All functions which could previously be
performed with V.A.G 1551 can also be
performed with the tester VAS 5051.

Warning light for ABS -K47- and warning light
for brake system -K118- flash when control
module is coded with 00000. An entry is not set
in the DTC memory.

The ABS control module (w/EDL) -J104- must
be recoded if the vehicle relevant coding is not
displayed or the control module has been
replaced.
Coding is only possible after the workshop code
(WSC) has been entered into the V.A.G 1551
Scan Tool.

Test sequence

- Connect V.A.G 1551 Scan Tool and select
(address word 03) "Brake electronics" with
ignition switched on; Page 01
-23

- Establish which type of ABS hydraulic control
module is installed Page 01
-4 .

- Establish engine code.
Стр. 38из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program

Downloaded from www.Manualslib.com manuals search engine 01-64


List of selectable display group numbers
Display group number
Display zone
Designation
001 1 Wheel speed at left front wheel sensor (km/h)
2 Wheel speed at right front wheel sensor (km/h)
3 Wheel speed at left rear speed sensor (km/h)
4 Wheel speed at right rear speed sensor (km/h)
002 1 Wheel speed at left front speed sensor (km/h)
2 Wheel speed at right front wheel sensor (km/h)
3 Wheel speed at left rear speed sensor (km/h)
4 Wheel speed at right rear speed sensor (km/h)
003 1 Brake light switch
2 Vacant
3 Vacant
4 Vacant
Стр. 44из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program