1998 VOLKSWAGEN BORA brake

Downloaded from www.Manualslib.com manuals search engine Brake pedal -
Assembly overview;
Adjusting brake light
switch
Стр. 12из 17 Electrical/electronic components and installing locations

Downloaded from www.Manualslib.com manuals search engine 01-152



12 -
Data Link
Connector
(DLC)

Location: In
center console
below
heating/air
conditioning
controls
module
13 -
Button for
ASR/ESP -
E256-

Vehicles with
ABS/EDL/ASR/ESP
only
14 -
ABS warning
light -K47-

Location: In
the instrument
cluster
Function:
Page 01
-155
15 -
Warning light
for brake
system -K118-

Location: In
the instrument
cluster
Function:
Page 01
-155
16 -
ASR/ESP
Control Lamp -
K155-

Location: In
the instrument
cluster
Function:
Page 01
-155
Стр. 13из 17 Electrical/electronic components and installing locations

Downloaded from www.Manualslib.com manuals search engine 01-155


Diagnostic Trouble Codes
(DTCs) displayed by
warning lights -K47-, -K118-
and -K155-
Warning lamps
Item
Designation
1 ABS warning light -K47-
2 Warning light for brake system -
K118-
3 ASR/ESP Control Lamp -K155-
Стр. 1из 4 Diagnostic Trouble Codes (DTCs) displayed by warning lights -K47-, -K118- and -K155-

Downloaded from www.Manualslib.com manuals search engine 01-156



ABS warning light -K47-

Electrical Wiring Diagrams,
Troubleshooting & Component Locations
binder
If the ABS warning light -K47- -1- does
not go out after switching ignition on and
completion of test sequence then the
malfunction may be:
-a- Voltage supply is below 10 Volt
-b- There is a malfunction in the ABS
The anti-locking brake system remains
switched off with an ABS malfunction -b-,
but the brake system remains fully
operational.
-c- Since the last time the vehicle was
started there was a temporary speed
sensor malfunction.
In the case of a sensor malfunction -c-,
the ABS warning light -K47- will
extinguish after restarting the engine and
attaining a speed of above 20 km/h
(approx. 13 mph).
-d- The connection from instrument
cluster to ABS Control Module (w/EDL) -
J104- is interrupted (open circuit).
-e- Instrument cluster is faulty.
Стр. 2из 4 Diagnostic Trouble Codes (DTCs) displayed by warning lights -K47-, -K118- and -K155-

Downloaded from www.Manualslib.com manuals search engine 01-157



Warning lights -K47- and -K118-

Electrical Wiring Diagrams,
Troubleshooting & Component Locations
binder
WARNING!
After the ABS warning light -K47- and
warning light for brake system -K118-
have illuminated, it is possible that the
rear wheels will lock-up earlier when
braking.
If the ABS warning light -K47- -1- goes
out but the warning light for brake
system -K118- -2- remains on, then the
malfunction may be:
-a- The parking brake is applied.
-b- There is a malfunction in the
activation of the warning light for brake
system -K118-.
-c- The brake fluid level is too low.
If the ABS warning light -K47- -1- and
the warning light for brake system -
K118- -2- illuminate, the ABS system is
faulty and the EBD (Electronic brake
pressure distribution) is not functioning.
Стр. 3из 4 Diagnostic Trouble Codes (DTCs) displayed by warning lights -K47-, -K118- and -K155-

Downloaded from www.Manualslib.com manuals search engine 01-159


On Board Diagnostic (OBD),
performing
Test prerequisites for OBD

The tires installed to all wheels must be of
the same (approved) size; tires inflated to
prescribed pressure.

Mechanical/hydraulic parts of the brake
system including brake light switch and
brake lights OK.

Hydraulic lines and connections not leaking
(visual check of hydraulic unit, brake
calipers, wheel cylinders, tandem master
brake cylinder).

ABS Control Module (w/EDL) -J104- is
correctly bolted to ABS Hydraulic Unit -
N55-.

Connector on ABS Control Module (w/EDL)
-J104- correctly plugged-in (retainer is
engaged).

Check contacts of ABS components for
damage and correct seating.

All fuses according to wiring diagram OK
(remove fuse from fuse holder to check).

Supply voltage OK (at least 10.0 V).
Стр. 1из 129 On Board Diagnostic (OBD), performing

Downloaded from www.Manualslib.com manuals search engine 01-162



Connecting VAS 5051

Selecting operating mode:
Selecting vehicle system:
The control module identification and
coding are indicated on the display.
Selecting diagnosis function:
All diagnostic functions available are
indicated on the display.
Note:
The following test sequences are for V.A.G
1551 scan tool. - Pull cover -1- off in direction of -arrow-.
- With ignition switched off, connect tester
VAS 5051 to Data Link Connector using
diagnosis cable VAS 5051/1 or VAS
5051/3.
- Press button on display for "Vehicle On
Board Diagnostic (OBD)".
- Press button "03 - brake electronics" on
the display.
- Press button on display for desired
function.
- Further measures see repair procedures.
Стр. 4из 129 On Board Diagnostic (OBD), performing

Downloaded from www.Manualslib.com manuals search engine 01-164



Note:

The ABS function is switched off in the control
module during the OBD. This is indicated by th
e
flashing of ABS warning light -K47- and warning
light for brake system -K118-. If there is a
malfunction currently, it will be indicated by the
lights being on constantly.

The DTC memory can be erased after
successful check and repair.
- With ignition switched off, connect V.A.G 1551
to diagnostic connection using cable V.A.G
1551/3 A.
- Connect VAS 5051 Page 01
-31 .
V.A.G - On Board Diagnostic HELP
1 - Ra
pid data transfer1)
2 - Blink code output1)
Indicated on display:
1) Is displayed alternately
If the display remains blank, check Data Link
Connector connection, Electrical check, Page
01-288 , test steps 21 and 22.
Note:
Depending on the program, additional operating
information can be printed out by pressing the
HELP key of V.A.G 1551.
The key is used for moving forward within
the program
The PRINT key is used for switching on the
printer (warning lamp in key comes on).
Стр. 6из 129 On Board Diagnostic (OBD), performing