1998 SUZUKI GRAND VITARA stop light

YH4
GRAND
VITARA
AIR CONDITIONING (OPTIONAL) 1B-9
ABNORMAL NOISE FROM CRANKSHAFT PULLEY
ConditionPossible CauseCorrection

A large rattling noise is heard at
idle or sudden acceleration.
Loosen pulley mounting bolt.

Worn or broken bearings.
Retighten bolt.

Replace bearings.
ABNORMAL NOISE FROM TENSION PULLEY
ConditionPossible CauseCorrection

Clattering noise is heard from
pulley.

Pulley cranks upon contact.
Worn or damaged bearings.

Cracked or loose bracket.
Replace bearings.

Replace or retighten bracket.
ABNORMAL NOISE FROM EVAPORATOR
ConditionPossible CauseCorrection

Whistling sound is heard from
evaporator.
Depending on the combination of
the interior / exterior
temperatures, engine rpm and
refrigerant pressure, the
refrigerant flowing out of the
expansion valve may, under
certain conditions, make a
whistling sound.
At times, slightly decreasing
refrigerant volume may stop this
noise.

Inspect expansion valve and
replace if faulty.
ABNORMAL NOISE FROM BLOWER MOTOR
ConditionPossible CauseCorrection

Blower motor emits a chirping
sound in proportion to its speed of
rotation.

Fluttering noise or large droning
noise is heard from blower motor.
Worn or damaged motor brushes
or commutator.

Leaves or other debris
introduced from fresh air inlet to
blower motor.
Repair or replace blower motor.

Remove debris and make sure
that the screen at fresh air inlet is
intact.

YH4
GRAND
VITARA
(A)
1
1. Make alignment marks
1. Steering wheel
Turn slowly till coil stops
Turn contact coil back about 2 and
a half turns
1. Align marks
3C1-6 AIR BAG STEERING WHEEL AND COLUMN
STEERING WHEEL
CAUTION:
Removal of the steering wheel allows the contact coil to turn
freely but do not turn the contact coil (on the combination
switch) more than allowable number of turns (about two and
a half turns from the center position clockwise or counter-
clockwise respectively), or coil will break.
REMOVAL
1) Remove driver air bag (inflator) module from steering wheel re-
ferring to ªDRIVER AIR BAG (INFLATOR) MODULEº earlier in
this section.
2) Remove steering shaft nut.
3) Make alignment marks on steering wheel and shaft for a guide
during reinstallation.
4) Remove steering wheel with special tool.
Special Tool
(A): 09944-36011
CAUTION:
Do not hammer the end of the shaft. Hammering it will
loosen the plastic shear pins which maintain the column
length and impair the collapsible design of the column.
CENTERING CONTACT COIL
1) Check that vehicle's wheels (front tires) are set at straight-ahead
position.
2) Check that ignition switch is at ªLOCKº position.
3) Turn contact coil counterclockwise slowly with a light force till
contact coil will not turn any further.
NOTE:
Contact coil can turn about 5 turns at maximum, that is, if
it is at the center position, can turn about two and a half
turns both clockwise and counterclockwise.
4) From the position where contact coil became unable to turn any
further (it stopped), turn it back clockwise about two and a half
rotations and align center mark with alignment mark.

YH4
GRAND
VITARA
BRAKES 5-3
SUBSTANDARD OR
CONTAMINATED BRAKE FLUID
Improper brake fluid, mineral oil or water in the fluid
may cause the brake fluid to boil or the rubber compo-
nents in the hydraulic system to deteriorate.
If primary piston cups are swollen, then rubber parts
have deteriorated. This deterioration may also be evi-
denced by swollen wheel cylinder piston cups on the
drum brake wheels.
If deterioration of rubber is evident, disassemble all
hydraulic parts and wash with alcohol. Dry these parts
with compressed air before assembly to keep alcohol
out of the system. Replace all rubber parts in the sys-
tem, including hoses. Also, when working on the
brake mechanisms, check for fluid on the linings. If ex-
cessive fluid is found, replace the linings.
If master cylinder piston seals are satisfactory, check
for leakage or excessive heat conditions. If condition
is not found, drain fluid, flush with brake fluid, refill and
bleed system.
The system must be flushed if there is any doubt as
to the grade of fluid in the system or if fluid has been
used which contained parts that have been subjected
to contaminated fluid.
DIAGNOSIS
ROAD TESTING BRAKES
Brakes should be tested on dry, clean, smooth and
reasonably level roadway which is not crowned. Road
test brakes by making brake applications with both
light and heavy pedal forces at various speeds to de-
termine if the vehicle stops evenly and effectively.
Also drive vehicle to see if it leads to one side or the
other without brake application. If it does, check the
tire pressure, front end alignment and front suspen-
sion attachments for looseness. See diagnosis chart
for other causes.
BRAKE FLUID LEAKS
Check the master cylinder fluid levels. While a slight
drop in reservoir level does result from normal lining
wear, an abnormally low level indicates a leak in the
system. In such a case, check the entire brake system
for leakage. If even a slight evidence of leakage is
noted, the cause should be corrected or defective
parts should be replaced.
If fluid level is lower than the minimum level of reser-
voir, refilling is necessary. Fill reservoir with specified
brake fluid.
Brake fluid: Refer to reservoir tank cap.
CAUTION:
Since brake system of this vehicle is factory-
filled with brake fluid indicated on reservoir
tank cap, do not use or mix different type of
fluid when refilling; otherwise serious damage
will occur.
Do not use old or used brake fluid, or any fluid
from a unsealed container.

YH4
GRAND
VITARA
1. Stop light switch
BRAKES 5-9
BRAKE PEDAL FREE HEIGHT CHECK
Remove foot rest and displace carpet and dash silencer(s) so as to
measure brake pedal free height between pedal face and asphalt
sheet installed on dash panel.
Brake pedal free height ªaº from asphalt sheet:
208 ± 218 mm (8.19 ± 8.58 in.)
If the measurement is not within the specification, check the posi-
tion of booster push rod clevis and / or stop light switch according
to the instruction shown in this section.
The free height varies depending on installation position of booster
push rod clevis and stop light switch.
BRAKE LIGHT SWITCH ADJUSTMENT
Adjustment should be made as follows when installing switch. Pull
up brake pedal toward you and while holding it there, adjust switch
position so that clearance between end of thread and brake pedal
return cushion (shown as ªbº in figure).
Then tighten lock nut to specified torque.
Clearance ªbº: 1.5 ± 2.0 mm (0.06 ± 0.08 in.)
Tightening Torque
(b): 7.5 N
.m (0.75 kg-m, 5.5 lb-ft)
EXCESSIVE PEDAL TRAVEL CHECK
1) Remove foot rest and displace carpet and dash silencer(s).
2) Start engine.
3) Depress brake pedal a few times.
4) With brake pedal depressed with approximately 30 kg (66 lbs)
load, measure pedal to asphalt sheet clearance ªcº.
Clearance ªcº: over 115 mm (4.53 in.)
5) If clearance ªcº is less than specification, the most possible
cause is either rear brake shoes are worn out beyond limit or air
is in lines.
Should clearance ªcº remain less than specification even after
replacement of brake shoes and bleeding of system, other pos-
sible but infrequent cause is malfunction of rear brake shoe ad-
justers or booster push rod length out of adjustment.

YH4
GRAND
VITARA
BRAKES 5-17
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Brake pipe 2-way (or 4-way) joint bolt232.317.0
Brake pipe flare nut161.611.5
Front caliperM88.00.86.0
Brake bleederplug
Front cali erM108.50.856.5Brake bleeder lugWheel cylinder7.50.755.5
LSPV7.50.755.5
LSPV mounting bolt
LSPV stay bolt232.317.0
LSPV spring nut
Wheel nut10010.072.5
Stop light switch lock nut7.50.755.5
REQUIRED SERVICE MATERIAL
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSE
Brake fluid
Indicated on reservoir
cap or described in owner's
manual of vehicle
To fill master cylinder reservoir.

To clean and apply to inner parts of master
cylinder caliper and wheel cylinder when
they are disassembled.

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-9
1-1. CUSTOMER COMPLAINT ANALYSIS
Record details of the problem (failure, complaint) and how it occurred as described by the customer.
For this purpose, use of such a questionnaire form as shown below will facilitate collecting information to the
point required for proper analysis and diagnosis.
CUSTOMER QUESTIONNAIRE (EXAMPLE)
Customer's name:Model:VIN:
Date of issue:Date Reg.Date of problem:Mileage:
Problem Symptoms

ªABSº warning light abnormal: fails to turn on/fails to go off /
flashes

Abnormal noise while vehicle is running: from motor, from valve,
other__________________

Wheel is locked at braking:

Pump motor does not stop (running):

Braking does not work:

Other:
Frequency of occurrence
Continuous/Intermittent ( times a day, a month) /
other______________
Conditions for Occurrence
of Problem

Vehicle at stop & ignition switch ON:

When starting: at initial start only / at every start / Other______________

Vehicle speed: while accelerating / while decelerating / at stop /
while turning / while running at constant speed /
other________________

Road surface condition: Paved road / rough road / snow-covered
road / other_________________

Chain equipment:
Environmental Condition
Weather: fair / cloudy / rain / snow / other___________________

Temperature: F (C)
Diagnostic Trouble Code

First check: Normal code/malfunction code ( )

Second check after
test drive: Normal code / malfunction code ( )

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-15
1. Battery
2. Main fuses
3. Ignition switch
4. Circuit fuses
5. ABS hydraulic unit / control module
5-1. Terminal arrangement for ABS hydraulic unit /
control module assembly
5-2. ABS fail-safe relay (Solenoid valve relay)
5-3. ABS pump motor relay
5-4. Pump motor
5-5. Solenoid valves
6. ªABSº warning lamp
7. Right-rear wheel speed sensor
8. Left-rear wheel speed sensor
9. Right-front wheel speed sensor
10. Left-front wheel speed sensor
11. Data link connector
12. Diagnosis connector
13. Stop lamp
14. Stop lamp switch
15. PCM (ECM+TCM) or ECM
16. G sensor (For 4WD model only)
17. 4WD switch (For 4WD model only)
18. 4WD indicator lamp (For 4WD model only)
19. 4WD controller (If equipped)
20. EBD warning lamp (Brake warning lamp)
21. Combination meter
22. Parking brake switch
23. Brake fluid lever switch
24. Warning lamp driver moduleWire colorB : Black
B / Bl : Black / Blue
B / O : Black / Orange
B / W : Black / White
Bl : Blue
Bl /B : Blue / Black
Bl / O : Blue / Orange
Br : Brown
G : Green
G / B : Green / Black
G / W : Green / White
Lg : Lightgreen
Lg / B : Lightgreen / Black
O / B : Orange / Black
O / G : Orange / Green
O / W : Orange / White
P : Pink
P / B : Pink / Black
V / G : Violet / Green
W / BI : White / Blue
W / G : White / Green
W / Y : White / Yellow
Y : Yellow
Y / B : Yellow / Black
SYSTEM CIRCUIT
TERMINALCIRCUIT
A1Right-rear wheel speed sensor (+)
A2Right-front wheel speed sensor (±)
A3Right-front wheel speed sensor (+)
A4G sensor ground (For 4WD model only)
A5ÐÐÐ
A6ÐÐÐ
A7Idle up signal
A8Diagnosis switch terminal
A9Stop lamp switch
A10Ground (For ABS control module)
A11ABS fail-safe relay
A12Right-rear wheel speed sensor (±)
A13Left-front wheel speed sensor (±)
A14G sensor signal (For 4WD model only)
A15ÐÐÐ
A16ÐÐÐ
A17ªABSº warning lamp
A18Left-rear wheel speed sensor (+)
A19Left-rear wheel speed sensor (±)
A20Left-front wheel speed sensor (+)
A21ÐÐÐ
A22Data link connector
A23ÐÐÐ
A244WD switch (For 4WD model only)
A25Ignition switch
A26ªEBDº warning lamp
A27ABS pump motor relay
A28Ground (For ABS pump motor)

YH4
GRAND
VITARA
7E-4 DIFFERENTIAL (FRONT)
Components and Functions
ComponentFunction
4WD switch
When the transfer shift lever is shifted to 4L or 4H position, this switch turns ON
and causes the 4WD control system to turn ON, unless it is shifted to N or 2H
within 1 second.
ECM or PCM
When the 4WD switch turns ON [unless it turns OFF within 1 second], this com-
ponent actuates the pump assembly. If the pressure in the air pump assembly
fails to increase higher than the set level even after the pump motor has run more
than 10 seconds, this component stops the motor to protect it.
Air pump assembly

Pump motor

Release valve

Pressure switchThe air pump assembly consists of a pump motor, release valve and a pressure
switch.
Pump motor:
Produces positive pressure which actuates the actuator.
Release valve:
Closes when transfer shift lever is shifted to 4H or 4L so that the positive pressure
is applied to the actuator, and opens when N or 2H to release the pressure to the
atmosphere.
Pressure switch:
Turns ON and OFF depending on the pressure level in the pump assembly
(whether higher or lower than the set pressure level). ECM or PCM detects the
pressure level through this switch.
Differential case assembly

Free axle hub

Axle lock clutch

ActuatorThe free axle hub, axle lock clutch and actuator are installed in the differential
left case. The positive pressure produced in the air pump assembly is applied
to the actuator which then pushes the axle lock clutch to be engaged with the free
axle hub. In this state, the drive force is transmitted to the front axle, resulting in
the 4WD mode.
When the actuator is free from the positive pressure [when it is under the atmo-
spheric pressure], the axle lock clutch is pushed back by the return spring force
and cannot be engaged with the free axle hub, resulting in the 2WD mode.
ª4WDº indicator lampIt lights up when 4WD control system is in the 4WD mode.