1998 SUZUKI GRAND VITARA steering rack assembly

YH4
GRAND
VITARA
STEERING WHEEL AND COLUMN 3C-13
1. Capsule
2. Steering column bracket
3. Plate
1. Steering column assembly
1. Steering column lower seal ªaº
CHECKING STEERING COLUMN FOR
ACCIDENT DAMAGE
NOTE:
Vehicles involved in accidents resulting in body damage,
where steering column has been impacted, may have a dam-
aged or misaligned steering column.
CHECKING PROCEDURE
1) Check that two capsules are attached to steering column brack-
et securely. Check clearance between capsules and steering
column bracket. Clearance should be 0 mm (0 in.) on both sides.
If found loose or clearance, replace steering column assembly.
2) Check two plates for any damages such as crack or breakage.
If anything is found faulty, replace as steering column assembly.
3) Take measurement ªaº as shown. If it is shorter than specified
length, replace column assembly with new one.
Length ªaº: 895
0.8 mm (35.24
0.03 in.)
4) Check steering column lower seal for breakage or deformation.
If found defective, replace.
5) Check steering shaft joints and shaft for any damages such as
crack, breakage, malfunction or excessive play.
If anything is found faulty, replace as steering shaft lower assem-
bly or steering column assembly.
6) Check steering shaft for smooth rotation.
If found defective, replace as column assembly.
7) Check steering shaft and column for bend, cracks or deforma-
tion.
If found defective, replace as column assembly.

YH4
GRAND
VITARA
AIR BAG STEERING WHEEL AND COLUMN 3C1-11
1. Steering column
2. Steering column mounting bolt
3. Steering column lower seal
1. Shift (key) interlock cable
2. Screw
1. Capsule
2. Steering column bracket
3. Plate
1. Steering column assembly ªaº
8) Remove steering column mounting bolts (6 pieces).
9) If equipped with shift (key) interlock cable, remove shift (key)
interlock cable screw and then disconnect its cable from igni-
tion switch.
10) Remove steering column from vehicle.
INSPECTION
NOTE:
Vehicles involved in accidents resulting in body damage,
where steering column has been impacted or air bag
deployed, may have a damaged or misaligned steering col-
umn.
CHECKING PROCEDURE
1) Check that two capsules are attached to steering column brack-
et securely. Check clearance between capsules and steering
column bracket. Clearance should be 0 mm (0 in.) on both sides.
If found loose or clearance, replace steering column assembly.
2) Check two plates for any damages such as crack or breakage.
If anything is found faulty, replace as steering column assembly.
3) Take measurement ªaº as shown. If it is shorter than specified
length, replace column assembly with new one.
Length ªaº: 895
0.8 mm (35.24
0.03 in.)

YH4
GRAND
VITARA
1. Steering column
2. Mounting bolt
3. Steering column lower seal
4. Dash panel
1. Steering column lower seal
In engine room
In cabin
1. Shift (key) interlock cable
2. Screw
3C1-12 AIR BAG STEERING WHEEL AND COLUMN
4) Check steering column lower seal for breakage or deformation.
If found defective, replace.
5) Check steering shaft joints and shaft for any damages such as
crack, breakage, malfunction or excessive play.
If anything is found faulty, replace as steering lower shaft assem-
bly or steering column assembly.
6) Check steering shaft for smooth rotation.
If found defective, replace as column assembly.
7) Check steering shaft and column for bend, cracks or deforma-
tion.
If found defective, replace as column assembly.
INSTALLATION
CAUTION:
After tightening steering column mounting bolts, steering
shaft joint bolts should be tightened.
1) Be sure that front wheels and steering wheel are in straight-
ahead position.
2) If equipped with shift (key) interlock cable, install shift (key) inter-
lock cable to ignition switch.
Tightening Torque
(a): 2.2 N
.m (0.22 kg-m, 1.6 lb-ft)
3) Install steering column assembly to dash panel and upper
bracket so that boss of steering column lower seal and all around
it project out of hole in dash panel into engine room. Tighten
steering column lower bolts (4 pieces) first and then upper bolts
(2 pieces) to specified torque.
Tightening Torque
(b): 23 N
.m (2.3 kg-m, 17.0 lb-ft)

YH4
GRAND
VITARA
AIR BAG STEERING WHEEL AND COLUMN 3C1-17
1. Capsule
2. Steering column bracket
3. Plate
1. Steering column assembly
1. Steering column lower seal ªaº
CHECKING STEERING COLUMN FOR
ACCIDENT DAMAGE
NOTE:
Vehicles involved in accidents resulting in body damage,
where steering column has been impacted or air bag
deployed, may have a damaged or misaligned steering col-
umn.
CHECKING PROCEDURE
1) Check that two capsules are attached to steering column brack-
et securely. Check clearance between capsules and steering
column bracket. Clearance should be 0 mm (0 in.) on both sides.
If found loose or clearance, replace steering column assembly.
2) Check two plates for any damages such as crack or breakage.
If anything is found faulty, replace as steering column assembly.
3) Take measurement ªaº as shown. If it is shorter than specified
length, replace column assembly with new one.
Length ªaº: 895
0.8 mm (35.24
0.03 in.)
4) Check steering column lower seal for breakage or deformation.
If found defective, replace.
5) Check steering shaft joints and shaft for any damages such as
crack, breakage, malfunction or excessive play.
If anything is found faulty, replace as steering shaft lower assem-
bly or steering column assembly.
6) Check steering shaft for smooth rotation.
If found defective, replace as column assembly.
7) Check steering shaft and column for bend, cracks or deforma-
tion.
If found defective, replace as column assembly.

YH4
GRAND
VITARA
4
3
1. Piston stopper circlip
2. Piston stopper
3. Cylinder cup and plate
4. Primary piston
5. Piston cup
6. Secondary piston pressure cup
7. Primary piston Assy
8. Secondary piston
9. Secondary piston Assy
10. Secondary piston stopper bolt
11. Master cylinder body
12. O-ring
[A] [B]
[A]: With ABS
[B]: Without ABS
5. Attaching nut
6. ABS control module
connector
7. Bracket bolt 1. Reservoir cap
2. Reservoir
3. Master cylinder
4. Flare nuts
5A-10 BRAKES PIPE / HOSE / MASTER CYLINDER
MASTER CYLINDER ASSEMBLY
REMOVAL
NOTE:
Do not allow brake fluid to get on painted surfaces.
1) Disconnect reservoir lead wire at coupler.
2) Clean around reservoir cap and take out fluid with syringe or
such.
3) Remove master cylinder with reservoir from brake booster.

For vehicle with ABS
a) Loosen flare nuts for master cylinder and ABS hydraulic
unit as shown.
b) For LH steering vehicle, disconnect ABS control module
connector.
c) For RH steering vehicle, remove ABS hydraulic unit brack-
et bolts.
d) Disconnect brake pipes between master cylinder and ABS
hydraulic unit.

For vehicle without ABS
a) Loosen flare nuts for master cylinder.
b) Disconnect brake pipes for master cylinder.

YH4
GRAND
VITARA
1. Ignition switch assembly
2. Clamp screw
3. Outer end
1. Interlock cable
2. Steering column
3. Steering column
holder
Type-1
1. Interlock cam
2. Lever plate
3. Interlock cable
4. Pin with 4 mm (0.15 in.) dia.
7B1-72 AUTOMATIC TRANSMISSION (4 A / T)
Installation
1) Shift select lever to ªNº range and turn ignition key to ªACCº
position.
2) Connect inner end of interlock cable to key interlock lever (Igni-
tion switch side).
3) Install outer end bracket of interlock cable to ignition switch as-
sembly, and tighten screw to specified torque.
Tightening Torque
(a): 2.2 N
.m (0.22 kg-m, 1.5 lb-ft)
4) Pass and connect interlock cable as shown at the left figure.
TYPE-1
5) Fix interlock cam by inserting pin with about 4 mm (0.15 in.) dia.
into holes of cam and lever plate.
6) Install cable end to interlock cam and stud bolt and after making
sure that cable outer is pushed in arrow direction B by leaf
spring, tighten mounting nut to specified torque. Remove pin.
Tightening Torque
(a): 13 N
.m (1.3 kg-m, 9.5 lb-ft)
7) Turn ignition key to ªACCº position and shift select lever to ªNº
range, and check for the followings.
a. When select lever is shifted at ªPº range with knob button
depressed, ignition key can not be turned from ªACCº to
ªLOCKº position.
b. When knob button is released, ignition key can be turned to
ªLOCKº position.
c. When ignition key is at ªLOCKº position, select lever can not
be shifted from ªPº to any other range.
8) Install console box.
9) Install steering column cover.
10) Adjust steering column or tighten steering column bolts.
11) Install steering column hole cover.
12) If equipped with air bag system, enable air bag system.
Refer to ªEnabling Air bag Systemº in Section 10B.

YH4
GRAND
VITARA
1. Yellow connector of passenger air bag (inflator) module
2. Steering support member
3. Air bag harness
AIR BAG SYSTEM 10B-57
3) Connect Yellow connector of passenger air bag (inflator) mod-
ule, and be sure to lock connector with lock lever.
ii) Connect connector.
ii) Lock connector with lock lever.
4) Install glove box.
5) Install ªAIR BAGº fuse to ªAIR BAGº fuse box.
6) Turn ignition switch to ON and verify that ªAIR BAGº warning
lamp flashes 6 times and then turns off.
If it does not operate as described, perform ªAir Bag Diagnostic
System Checkº in this section.
HANDLING AND STORAGE
SDM
WARNING:
Never power up air bag system when SDM is not rigidly at-
tached to the vehicle. Otherwise, personal injury may result.
CAUTION:
After detecting one time of such collision as to meet deploy-
ment conditions, the SDM must not be used.
Refer to ªDiagnosisº when checking the SDM.

Never attempt disassembly of SDM.

When storing SDM, select a place where neither high tempera-
ture nor high humidity is anticipated and oil, water and dust are
kept off.

If SDM was dropped from a height of 90 cm (3 ft) or more or if it
is found to be damaged or deformed, replace it with a new one.

If installation part of SDM was damaged, repair that part com-
pletely before reinstallation.

All SDM and mounting bracket fasteners must be carefully
torqued and the arrow must be pointed toward the front of the ve-
hicle to ensure proper operation of the air bag system.

YH4
GRAND
VITARA
10B-64 AIR BAG SYSTEM
ACCIDENT WITH OR WITHOUT DEPLOYMENT ± COM-
PONENT INSPECTIONS
Certain air bag and restraint system components must be in-
spected after any crash, whether the air bag deployed or not.
Those components are:

Steering column and shaft joints
± Check for length, damage and bend according to ªChecking
Steering Column for Accident Damageº in SECTION 3C1.

Steering column bracket and capsules
± Check for damage and bent.
If any faulty condition is found in above checks, replace faulty
part.

Steering wheel and driver air bag (inflator) module
± Check for damage or air bag (inflator) module fitness.
± Check trim cover (pad surface) for cracks.
± Check wire harness and connector for damage or tightness.
If any faulty condition is found in above checks, replace faulty
part.

Contact coil and combination switch assembly
± Check wire harness and connectors for damage or tightness.
± Check contact coil case for damage.
If any faulty condition is found in above checks, replace.

Instrument panel member and reinforcement
± Check for any distortion, bending, cracking or other damage.
If any faulty condition is found in above checks, replace.