1998 SUZUKI GRAND VITARA tem

YH4
GRAND
VITARA
AIR BAG STEERING WHEEL AND COLUMN 3C1-3
DIAGNOSIS
For diagnosis of the steering wheel and steering column, refer to
Section 3. For diagnosis of the air bag system, refer to Section 10B.
INSPECTION AND REPAIR REQUIRED AFTER
ACCIDENT
After an accident, whether the air bag has been deployed or not, be
sure to perform checks, inspections and repairs described under
ªCHECKING STEERING COLUMN FOR ACCIDENT DAMAGEº in
this section as well as ªREPAIRS AND INSPECTIONS REQUIRED
AFTER ACCIDENTº in Section 10B.
ON-VEHICLE SERVICE
SERVICE PRECAUTIONS
For service precautions, refer to ªSERVICE PRECAUTIONSº un-
der ªON-VEHICLE SERVICEº in Section 10B.
DIAGNOSIS AND SERVICING
For diagnosis and servicing, refer to ªDIAGNOSIS AND SERVIC-
INGº under ªSERVICE PRECAUTIONSº in Section 10B.
DISABLING AIR BAG SYSTEM
For disabling air bag system, refer to ªDISABLING AIR BAG SYS-
TEMº under ªSERVICE PRECAUTIONSº in Section 10B.
ENABLING AIR BAG SYSTEM
For enabling air bag system, refer to ªENABLING AIR BAG SYS-
TEMº under ªSERVICE PRECAUTIONSº in Section 10B.
HANDLING AND STORAGE
For handling and storage, refer to ªHANDLING AND STORAGEº
under ªSERVICE PRECAUTIONSº in Section 10B.
DISPOSAL
For disposal, refer to ªDISPOSALº under ªSERVICE PRECAU-
TIONSº in Section 10B.

YH4
GRAND
VITARA
1 11
1. Mounting bolt
1. Driver air bag (inflator) module connector
2. Horn connector
3. Driver air bag (inflator) module
4. Steering wheel
3C1-4 AIR BAG STEERING WHEEL AND COLUMN
DRIVE AIR BAG (INFLATOR) MODULE
WARNING:
When handling an air bag (inflator) module, be sure to read
ªSERVICE PRECAUTIONSº under ªON-VEHICLE SERVICEº
in Section 10B and observe each instruction. Failure to fol-
low them could cause a damage to the air bag (inflator) mod-
ule or result in personal injury.
REMOVAL
1) Disconnect negative battery cable at battery terminal.
2) Disable air bag system. Refer to ªDISABLING AIR BAG SYS-
TEMº under ªSERVICE PRECAUTIONSº in Section 10B.
3) Loosen 2 bolts mounting driver air bag (inflator) module till it
turns freely, pull them out and fix them to bolt clamps.
4) Remove air bag (inflator) module from steering wheel.
5) Remove driver air bag (inflator) module (yellow) connector and
horn connector from steering wheel.
6) Disconnect driver air bag (inflator) module (yellow) connector of
driver air bag (inflator) module and horn connector as shown in
the figure.
ii) Release locking of lever.
ii) After unlocked, disconnect connector.
WARNING:
Special care is necessary when handling and storing a
live (undeployed) air bag (inflator) module. Observe
ªSERVICE PRECAUTIONSº under ªON-VEHICLE SER-
VICEº in Section 10B. Otherwise, personal injury may re-
sult.

YH4
GRAND
VITARA
6, (a)
1. Trim cover (pad surface)
2. Inflator case
3. Wire harness
1. Driver air bag (inflator) module connector
2. Horn connector
3. Driver air bag (inflator) module
4. Steering wheel
5. Mounting bolt (left side)
6. Mounting bolt (right side)
AIR BAG STEERING WHEEL AND COLUMN 3C1-5
INSPECTION
WARNING:
Never disassemble air bag (inflator) module or measure its
resistance. Otherwise, personal injury may result.
CAUTION:
If air bag (inflator) module was dropped from a height of
90 cm (3 ft) or more, it should be replaced.
Check air bag (inflator) module visually and if any of the following
is found, replace it with a new one.

Air bag being deployed.

Trim cover (pad surface) being cracked.

Wire harness or connector being damaged.

Air bag (inflator) module being damaged or having been exposed
to strong impact (dropped).
INSTALLATION
1) Connect horn connector securely.
2) Connect yellow connector of driver air bag (inflator) module con-
nector as shown in the figure securely.
ii) Connect connector.
ii) Lock connector with lock lever.
3) Install horn connector and driver air bag (inflator) module con-
nector.
4) Install driver air bag (inflator) module to steering wheel, taking
care so that no part of wire harness is caught between them.
5) Make sure that clearance between module and steering wheel
is uniform all the way.
6) Tighten driver air bag (inflator) module mounting bolt (left side)
to specified torque first and then driver air bag (inflator) module
mounting bolt (right side) to specified torque.
Tightening Torque
(a): 9 N
.m (0.9 kg-m, 6.5 lb-ft)
7) Connect negative battery cable.
8) Enable air bag system. Refer to ªENABLING AIR BAG SYS-
TEMº under ªSERVICE PRECAUTIONSº in Section 10B.

YH4
GRAND
VITARA
1. Steering column assembly
2. Steering shaft joint
3. Marks
1. Steering column assembly
2. Steering shaft joint
3. Steering lower shaft assembly
4. Bolt (column side)
5. Bolt (lower shaft assembly side)1. Steering column hole cover
1
3C1-10 AIR BAG STEERING WHEEL AND COLUMN
REMOVAL
WARNING:
Never rest a steering column assembly on the steering
wheel with air bag (inflator) module face down and column
vertical. Otherwise personal injury may result.
1) Disconnect negative battery cable at battery terminal.
2) Disable air bag system. Refer to ªDISABLING AIR BAG SYS-
TEMº under ªSERVICE PRECAUTIONSº in Section 10B.
3) Remove steering wheel and contact coil and combination switch
assembly, if necessary. Refer to ªSTEERING WHEELº and
ªCONTACT COIL AND COMBINATION SWITCH ASSEMBLYº
in this section.
Perform the following procedure if not removing steering wheel
and/or combination switch.
ii) Turn steering wheel so that vehicle's front tires are at straight-
ahead position.
ii) Turn ignition switch to ªLOCKº position and remove key.
4) Remove steering column hole cover.
5) Disconnect all connectors for the following parts.

Contact coil and combination switch

Ignition switch
6) Make alignment marks on shaft joint and shaft (column side) for
a guide during reinstallation.
7) After removing bolt on column side of shaft joint and loosening
bolt on its lower shaft assembly side, move shaft joint to lower
shaft assembly side (in arrow direction in the figure).

YH4
GRAND
VITARA
1. Steering shaft joint
2. Steering shaft (column side)
3. Marks
1. Steering shaft joint
2. Bolt (column side)
3. Bolt (lower shaft assembly side)
1. Steering column hole cover
1
AIR BAG STEERING WHEEL AND COLUMN 3C1-13
4) Install steering shaft joint to steering shaft by matching it to
marks made before removal.
5) Install shaft joint bolt (column side) to steering shaft joint. Tighten
shaft joint bolt (column side) to specified torque first and then
shaft joint bolt (lower shaft assembly side) to specified torque.
Tightening Torque
(c): 25 N
.m (2.5 kg-m, 18.0 lb-ft)
6) If contact coil and combination switch assembly is removed,
install it, referring to ªCONTACT COIL AND COMBINATION
SWITCH ASSEMBLYº in this section.
7) Connect all connectors that have been removed in removal.
8) Install steering column hole cover.
9) If steering wheel is removed, install it by referring to ªSTEER-
ING WHEELº in this section.
10) Connect negative battery cable.
11) After installing steering column assembly, be sure to enable air
bag system by referring to ªENABLING AIR BAG SYSTEMº un-
der ªSERVICE PRECAUTIONSº in Section 10B.

YH4
GRAND
VITARA
3D
FRONT SUSPENSION 3D-1
GENERAL DESCRIPTION3D- 2 . . . . . . . . . . . . . .
DIAGNOSIS3D- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table 3D- 3. . . . . . . . . . . . . . . . . . . . . .
Stabilizer Bar and Bushing Check 3D- 3. . . . . .
Strut Damper and / or Coil Spring Check 3D- 3. .
Suspension Arm / Knuckle Check 3D- 3. . . . . . . .
Suspension Control Arm Joint Check 3D- 4. . . .
Suspension Control Arm Bushing Check 3D- 4.
Wheel Disc, Nut & Bearing Check 3D- 4. . . . . .
ON-VEHICLE SERVICE3D- 5 . . . . . . . . . . . . . . . . Stabilizer Bar / Bushings 3D- 5. . . . . . . . . . . . . . .
Strut Damper 3D- 6. . . . . . . . . . . . . . . . . . . . . . . .
Coil Spring 3D- 8. . . . . . . . . . . . . . . . . . . . . . . . . .
Bump Stopper / Spring Rubber Seat 3D-11. . . . .
Wheel Hub (Included Wheel Bearing) 3D-12. . .
Knuckle / Wheel Spindle 3D-17. . . . . . . . . . . . . . . .
Suspension Control Arm / Bushings 3D-21. . . . . .
TIGHTENING TORQUE
SPECIFICATIONS3D-23 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS3D-24 . . . . . .
SPECIAL TOOLS3D-25 . . . . . . . . . . . . . . . . . . . . . .
SECTION 3D
FRONT SUSPENSION
CAUTION:

All front suspension fasteners are an important attaching part in that it could affect the performance
of vital parts and systems, and / or could result in major repair expense. They must be replaced with
one of the same part number or with an equivalent part if replacement becomes necessary. Do not
use a replacement part of lesser quality or substitute design. Torque values must be used as specified
during reassembly to assure proper retention of this part.

Never attempt to heat, quench or straighten any front suspension part. Replace it with a new part or
damage to the part may result.
CONTENTS

YH4
GRAND
VITARA
FRONT SUSPENSION 3D-9
1. Coil spring
8) Remove stabilizer bar, refer to steps 2) to 5) of item STABILIZ-
ER BAR / BUSHINGS REMOVAL in this section.
9) Disconnect tie rod end from knuckle by using puller.
10) Support lower arm, using jack as shown.
11) Remove strut bracket bolts.
12) Remove ball stud castle nut.
13) Using puller, disconnect knuckle from ball stud.
14) Remove knuckle and wheel hub comp, while lowering jack.
15) Remove coil spring.

YH4
GRAND
VITARA
FRONT SUSPENSION 3D-11
1. Front wheel speed sensor
2. Bolt
1. Spring rubber
seat
2. Bump stopper2, (b)
1

Check that no foreign material is attached to sensor and rotor.
Install wheel speed sensor and its harness clamp.
Tightening Torque
(a): 10 N
.m (1.0 kg-m, 7.5 lb-ft)
(b): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
CAUTION:

Do not pull wire harness or twist more than necessary
when installing front wheel speed sensor.

Fit harness grommet to inner fender securely.

Check that there is no clearance between sensor and knuckle.
BUMP STOPPER / SPRING RUBBER SEAT
REMOVAL
1) Remove coil spring. Refer to steps 1) to 15) of item ªCOIL
SPRING REMOVALº in this section.
2) Remove spring rubber seat.
3) Remove bump stopper, using special tool.
Special Tool
(A): 09941-66010
INSTALLATION
1) Tighten bump stopper to specified torque, using special tool.
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
2) Install spring rubber seat.
3) Install coil spring. Refer to item ªCOIL SPRING INSTALLATIONº
in this section.