1998 SSANGYONG MUSSO display

5D2-22 TRANSFER CASE (TOD)
Check function of TOD control unit.
1. Even A1, A2, A3 and A4 test, if you could not find defect,
it is required to replace TOD control unit on basis of
below phenomena.
a. ”4WD CHECK” lamp illuminates continuously when
ignition “ON”.
b. Shift is not possible even 4H/4L switch operation.
c. Upon diagnosis by Scan-100, it displays on
“impossible communication with TOD control unit”
or fault code “1714, 1715, 1716”.
- Do occur the above defects? Yes
NoReplace TOD control
unit
Normal system A5Test Stage / Contents
Result
Stage Test Contents and ProcedureSpecified Value
/Yes/NoCountermeasure

TRANSFER CASE (TOD) 5D2-23
Error of signal in engine throttle position ; fault
code 1715, 1716
lPhenomenon
1. Upon diagnosis by SCAN-100, it display on 1715,
1716 codes.
lCause
1. Bad communication line between E/G ECU and CAN.
2. Defect of TOD control unit.
3. Defect of E/G ECU.
Check connection status of connector through CAN
communication line.
1. Check connection of connector.
- Does connector connect correctly between TOD
control unit and E/G ECU?
2. In case of bad connection, connect correctly then
perform the follows ;
a. Delete the memorized fault code using SCANNER.
b. Ignition “OFF”.
c. Ignition “ON”.
d. Diagnose by SCANNER.
- Does it display fault codes “1715” or “1716”.Ye s
No
B1
Ye s
No
Check connection status of CAN communication line towards
E/G ECU.
1. Ignition “OFF”.
2. Disconnect 30 pin connector towards TOD control unit.
3. Measure resistance between pin No.22 and 23 in wiring
connector using multi-tester.
- Specified value
- Measured value is within specified range? B2
115-125W
Ye s
No
Check connection status of CAN communication line towards
TOD control unit.
1. Ignition “OFF”.
2. Disconnect coupling of E/G ECU (gray, 1-60 pin).
3. Measure resistance between pin No.37 and 38 in
coupling using multi-tester.
- Specified value
- Measured value is within specified range? B3
115-125W
Ye s
No Test Stage / Contents
Result
Stage Test Contents and ProcedureSpecified Value
/Yes/NoCountermeasure
Perform B2 stage
Perform B1-2 stage
Perform B2 stage
Normal system
Perform B3 STAGE
Perform B4 stage,
check and replace E/
G ECU
Perform B5 STAGE
Replace TOD control
unit

5D2-24 TRANSFER CASE (TOD)
Ye s
No B4
B5
Ye s
No
B6
4.75-5.25Vdc
Ye s
No
B70.3-0.9Vdc
4.6-4.9Vdc
Ye s
No
4.6-4.9Vdc
0.3-0.9Vdc
Ye s
No Test Stage / Contents
Result
Stage Test Contents and ProcedureSpecified Value
/Yes/NoCountermeasure
Check CAN communication line by diagnosis of E/G ECU.
1. Diagnose E/G ECU with SCANNER.
2. Does it display on fault code “27” ?
Check power supply and signal output on throttle valve
position sensor (potentiometer) 1,2.
1. Diagnose E/G ECU with SCANNER.
- Fault codes : 104, 105, 108, 109, 119, 185
Does it display on above code ?
Check power supply (5V) of throttle valve position sensor.
1. Ignition “ON”
2. Measure voltage between pin 112(+) and 84(-) keeping
coupling connection status using multi - tester.
- Specified value
- Measured value is within specified range ?
Check output signal from throttle position sensor 1 and 2.
1. Keep E/G idle status.
2. Measure output voltage between pin 87 (+) and 84 (-)
keeping E/G ECU coupling connection status using multi-
tester. (potentiometer 1)
- Specified value min. acc. Pedal
max. acc. Pedal
- Measured value is within specified range ?
3. Measure output voltage between pin 85 (+) and 84 (-)
keeping E/G ECU coupling connection status using multi-
tester. (potentiometer 2)
- Specified value min. acc. Pedal
max. acc. Pedal
- Measured value is within specified range ?
Replace TOD control
unit
Replace throttle body
actuator or check
cable Perform B1, B2, B3
stages
Perform B5 stage
Perform B6 stage
Replace TOD control
unit or perform A1-
A5 stages
Perform B7 stage
Replace E/G ECU or
perform B1-2 stage
after checking cable.
Perform B7-3 stage
Replace throttle body
actuator or check
cable.

TRANSFER CASE (TOD) 5D2-25
Error in electro - magnetic clutch : fault code
“1721”, “1722”
lPhenomenon
1. Upon diagnosis by SCAN-100, it displays on fault
codes “1721,1722”.
lCause
1. Defect in electro - magnetic clutch
2. Defect in connector or wiring
- Open or short from EMC to the supply : 1721
- Short EMC to ground : 1722
Ye s
No
C1
Ye s
No Ye s
No
11-15Vdc
Ye s
No
C2
Ye s
No
Test Stage / ContentsResult
Stage Test Contents and ProcedureSpecified Value
/Yes/NoCountermeasure
Check relevant connector connection status.
1. Check relevant connector connection status with TOD
control unit.
- Does it connect correctly ?
2. Check connection status of speed sensor and clutch
coil connector (7 pin) in transfer case.
- Does it connect correctly ?
3. In case of bad connection, connect it correctly then
perform the follows :
a. Delete the memorized fault code in control unit with
Scan - 100.
b. Ignition “OFF”.
c. Ignition “ON”.
d. Diagnose by SCAN-100
- Does it display on fault codes “1721,1722” ?
Check supply voltage into electro-magnetic clutch.
1. Ignition “ON”
2. Measure voltage between pin 4/19(+) and 17/18(-) in
TOD control unit connector.
- Specified value
- Measured value is within specified range ?
3. If the specified value would not be measured, perform
the follows :
a. Check battery voltage (charging condition)
b. Check open circuit on No.13 fuse (20A)
c. Check relevant wires.
- Is the above 3a, 3b, 3c normal ?Perform C1-2 stage
Perform C1-3 stage
Perform C2 stage
Normal system Perform C2 stage
Perform C1-3 stage
Perform C3 stage
Perform C2-3 stage
Perform C3 stage
lCharging/
Replace battery
lReplace fuse
lRepair wires

TRANSFER CASE (TOD) 5D2-27
Defect in speed sensor : fault code 1731, 1732,
1733, 1734, 1735,1736
lPhenomenon
1. Upon diagnosis by SCANNER, it displays on fault code
1731, 1732, 1733, 1734, 1735 and 1736.
2. “4WD CHECK” lamp illuminates continuously when
ignition “ON”.
lCause
1. Defect of speed sensor (front, rear).
2. Defect of power supply.
4.75-5.25Vdc
Ye s
No D1
Ye s
No
D2
Ye s
Ye s
Ye s
No D3Test Stage / Contents
Result
Stage Test Contents and ProcedureSpecified Value
/Yes/NoCountermeasure
Check power supply of speed sensor.
1. Ignition “ON” or driving mode
2. Measure supply voltage between pin 16 (+) and 13 (-) in
TOD control unit connector using digital multi-tester.
- Specified value
- Measured value is within specified range ?
Check connection status of connector.
1. Check connection status of speed sensor/clutch coil
connector and TOD control unit connector.
- Does it connect correctly ?
2. In case of bad connection, connect it correctly then
perform the follows:
a. Delete the memorized fault code in control unit by
SCANNER.
b. Ignition “OFF”.
c. Ignition “ON”.
d. Diagnose by SCANNER.
- It does not display fault code.
- It displays one or more fault code among 1731 to
1736.
Check output wave of front and rear speed sensor.
1. Upon driving mode.
2. Check output wave of each speed sensor by SCANNER.
3. Is it normal on output wave ?Perform D3 stage
Perform D2 stage
Perform D3 stage
Perform D2-2 stage
Normal system
Perform D3 stage
Perform D4 stage
Replace speed
sensor then
perform D2-2 stage

TRANSFER CASE (TOD) 5D2-29
Shift motor malfunction : Fault code ® 1741,
1742, 1743
lPhenomenon
1. When change the 4H/4L switch from 4H to 4L, ‘4L’
indicator lamp turn off after blinking for a time and then
‘4WD CHECK’ indicator lamp turn on.
2. Fault codes display by diagnosis of SCAN-100 : 1741,
1742, 1743
3. The shifting operation is not occurred when 4H / 4L switch,
is operating.
lCause
Defect in shift motor, improper voltage provided, incorrect
connection in connector, short of wiring.
11-14 V
(Battery voltage)
Ye s
No E1
11-14 V
(Battery voltage)
Ye s
No
Ye s
No
E2
Ye s
No Test Stage / Contents
Result
Stage Test Contents and ProcedureSpecified Value
/Yes/NoCountermeasure
Check the input voltage of shift motor.
1. Turn the ignition switch to “ON” position.
2. Measure the Hi/Low voltage of motor which is located
between No.1/No.14 and No.2/No.15 connector of TOD
control unit with digital Multi-tester or which is located
between No.G connector and body after detaching T/C
motor connector.
- The specified value (When operates 4H/4L switch)
- Measured value is within specified range ?
3. Measure the Hi/Low voltage of motor which is located
between No.2/No.5 and No.1/No.14 connector or which
is located No.B connector and body after detaching T/C
motor connector
- The specified value (When operates 4H/4L switch)
- Measured value is within specified range ?
Check the fault condition of the relevant connector.
1. Check the installation condition of TOD control unit 30pin
connector and T/C shift motor connector.
- Is it installed properly ?
2. If the connector installation is improper, install properly
and then perform follows :
a. Delete the fault code of control unit by scan scope
b. Turn off the ignition switch
c. Turn on the ignition switch
d. Re-diagnosis of system
It displays one or more fault code among 1741 to 1743.Perform E1-3 stage
Perform E2 stage
Perform E4 stage
Perform E2 stage
Perform E3 stage
Perform E2-2 stage
Perform E3 stage
Normal system

TRANSFER CASE (TOD) 5D2-31
Position incoder and position 1,2,3,4 malfunction
:Fault code®1750,1751,1752,1753, 1754
lPhenomenon
The ‘4WD check’ lamp can not go out when the ignition
switch positioned to ‘ON’.
The fault code display 1750, 1751, 1752, 1753, 1754 by
diagnosis of SCAN-100.
lCause
The portion of position incoder malfunction, each wiring is
shorted with ground.
Ye s
No
F1
Ye s
No
Ye s
No F2Test Stage / Contents
Result
Stage Test Contents and ProcedureSpecified Value
/Yes/NoCountermeasure
Check the installation condition of connector.
1. Check the installation condition between 30 pin connector
of TOD control unit and motor connector of T/C portion.
- Is it installed properly ?
2. If the connector installation is improper, install properly
and then execute follow procedure.
a. Delete the all fault code from memory by scan scope.
b. Turn off ignition switch.
c.Turn on ignition switch.
d. Rediagnosis the system.
- Does the fault codes display one or more among
1750 ~ 1754.
Check the each wiring whether it is shorted or not.
1. Turn off the ignition switch
2. Detach the 30 pin connector of TOD control unit.
3. Perform short test each connector, No.27 (Position 1),
No.10 (Position 2), No.28 (Position 3),No.30 (Position
4), No.6 with body.
- Is there resistance of 0W?Perform F2 stage
Perform F1-2 stage
Perform F2 stage
Normal system
Repair or replace
due to wiring short
1. Replace the
motor Ass’y due
the defective
position incoder
portion.
2. And then, perform
F1-2 stage.

SUPPLEMENTAL RESTRAINT SYSTEM(SRS) 8B-7
DIAGNOSIS
DESCRIPTION
Air bag control unit continuously controls system function as follows during ignition ON or driving.
- Recognition of collision
- Internal diagnosis
- External diagnosis
If recognize or detect defects, warning lamp will turn on. If there is danger of improper deployment, the system will
enter overall shutdown status and the air bag will not inflate.
Air bag control unit will store detected internal and external defects in the EEPROM.
System Control
Battery Voltage Check
Battery voltage will be monitored continuously. If voltage is out of normal operating range, all system diagnosis will
stop and warning lamp turn on.
Battery Voltage (V)
< 8.7
9 - 16
> 16.3
Function
System diagnosis stops and warning lamp turns on
Normal operation range
System diagnosis stops and warning lamp turns on
Squib Diagnosis
It checks not only high (4.50.5) or low (1.40.5) resistance but also short resistance (1- 10k) status between the
battery and ground to indicate defects in squib line by blinking warning lamp. Air bag control unit (AC4) can measure
squib resistance.
Warning Lamp Turning On
Air bag control unit detects system defects during ignition ON or driving and displays following 2 warning lamps.
- Warning lamp ON: internal defects of the air bag control unit
- Warning lamp blinking: higher resistance than standard in the squib line or short at the battery or ground,
Safety Function Check
It checks defects during operation of the arming sensor If the sensor is shorted for more than 2 seconds, the module
will enter overall shutdown mode.
Temperature Sensor
Function of the temperature sensor will be monitored continuously. If there is fault due to defective sensor or short,
the lamp will turn on and program will take calibration temperature (25) of collision conditions.
Power Supply
Airbag control unit operates in 9-16v and the characteristic of the system has backup condenser to supply the power
for max.150ms if there is power defect during collision.