1998 SSANGYONG MUSSO engine

7B/C-14 MANUAL & SEMIAUTO-HVAC
CONDENSER
Preceding Work : Removal of the radiator
1 Bolt
2 Condenser Fan
3 Bolt
4 Condenser
Diesel Engine

7B/C-16 MANUAL & SEMIAUTO-HVAC
1 Main Condenser Fan
2 Auxiliary Condenser Fan3 Bolt
4 Condenser
Gasoline Engine

7B/C-18 MANUAL & SEMIAUTO-HVAC
RECEIVER DRIER
Diesel Engine
1 Condenser
2 Receiver Drier
3 Bolt......................................................... 4-6 Nm4 Bolt..........................................................5-8 Nm
5 Bracket

7B/C-20 MANUAL & SEMIAUTO-HVAC
1 Condenser
2 Receiver Drier3 Bracket
Removal & Installation Procedure
1. Disconnect the dual pressure switch connector from the
receiver drier.
2. Discharge refrigerant from the system.
3. Remove the high pressure pipe from the inlet / outlet of
receiver drier.
4. Remove the bracket bolts and remove the receiver drier.
5. Installation should follow the removal procedure in the
reverse order.
Gasoline Engine

MANUAL & SEMIAUTO-HVAC 7B/C-21
COMPRESSOR
Preceding Work : Removal of the poly V-belt
Diesel Engine
1 Low Pressure Pipe
2 High Pressure Pipe3 Compressor Bracket
4 Compressor

MANUAL & SEMIAUTO-HVAC 7B/C-23
Gasoline Engine
1 Low Pressure Pipe
2 High Pressure Pipe3 Compressor Bracket
4 Compressor
Removal & Installation Procedure
1. Disconnect the negative(-) terminal from the battery.
2. Discharge refrigerant from the system.
Notice
By connecting a manifold gauge connection hose to High/
Low pressure line, discharge the refrigerant.
3. Disconnect the high / low pressure pipe and wire connectors.

SUPPLEMENTAL RESTRAINT SYSTEM(SRS) 8B-3
CAUTIONS
Failure to follow the correct service procedure can cause air bag damage or personal injury due to unexpected air
bag deployment. Before service (removal and installation of part, check for replacement), please be weal noticed of
following items for your correct service.
1. For service, turn the ignition switch to ‘LOCK’ position and wait for 30 seconds after disconnecting the negative
battery cable.
2. If the vehicle collapsed, remove the air bag ECU first to reserve the crash records.
3, Never use other vehicles’ air bag components and replace with specified new part.
4. Never disassemble or repair the air bag module, air bag unit and wiring harness to re-use.
5. Replace the air bag module and air bag unit with new if it dropped, cracked or damaged.
6. Only qualified technicians in service shop should check or repair the air bag,
7. Before service, should be well noticed of warning labels on the vehicle.
A. Sun Visor Side
[Warning]
Pull down the sun visor and see SRS air bag
warning lamp on the head lining.
B. Head Lining
[Warning]
1 . This vehicle is equipped with air bag. Air bag is
supplemental device for the seatbelt. Fasten
your seatbelt.
2. This air bag should be replaced by authorized
supplier within replacement intervals.
3. When the ignition key is turned to ON position,
SRS warning lamp will turn on for 6 sec. and go
off. In this case, the system is normal.
For the following cases, see service manual.
- SRS warning lamp does not turn on.
- SRS warning lamp does not go off.
- SRS warning lamp continues to blink.
C. Steering Wheel Body Inner
[Warning]
Before removing the steering wheel, read service
manual first. Set the front wheels straight forward
and align the center position marks of SRS clock
spring. Improper removal or installation of the
steering wheel can damage the SRS components.D. Engine Compartment
[Warning]
This vehicle is equipped with air bag. Before
checking the engine compartment, read service
manual first. Faultuy check and service can cause
SRS air bag deployment and system defects that
can be led to severe damage.
E. Battery Cable
[Warning]
Before disconnecting the battery power, read
service manual first.

8B-10 SUPPLEMENTAL RESTRAINT SYSTEM(SRS)
1. Position the ignition switch to ‘OFF’.
2. Connect the harness connector of scanner to the diagnosis
socket in engine compartment.
3. Turn the ignition switch to ‘ON’ position.
4. Select “Electronic control vehicle diagnosis” from function
selection display and press ‘Enter’.
5. Select “Musso (’98 model year)” from vehicle model
selection display and press ‘Enter’.
6. Select “Electronic air bag” from control system selection
display and press ‘Enter’.
7. Select “Self-diagnosis” from diagnosis item selection display.
Notice
Check sensor value of output display, if necessary.
8. Determine the fault code and trace defective component.
Notice
Refer to self-diagnosis list.
SELF DIAGNOSIS