1998 PONTIAC FIREBIRD keyless entry

Arming the System
The alarm system can be
armed to detect break-ins
by locking your vehicle
using the remote keyless entry transmitter or by
locking the
doors with the
power door lock switch.
Passive arming is
also available, if you would like the
system to arm all by itself after the doors have been
closed for a short time. When the system is armed,
a red
light will flash briefly once every two seconds. (Note:
If
you return to your vehicle and the red light is flashing
two brief flashes every two seconds, the system is armed
and the shock sensor had triggered a two minute alarm.
If the red light is flashing three times every two seconds,
the system is armed and there was an intrusion that
sounded the alarm.) Horn chirps and parking lamp
flashes can be set to your choice.
Remote Keyless Entry Transmitter Locking
If all the doors are closed, locking the vehicle with the
remote keyless entry transmitter will immediately
arm
the system. The horn will chirp twice and the parking
lamps will flash, confirming that the system is armed.
If
any door is open when the transmitter LOCK button is
pressed, the system goes into an armed wait mode,
waiting for the doors to close. Once they are closed, the
system will
arm, the horn chirps twice and the parking
lamps will flash. If the hatch is open or ajar at the time
the system is arming, the horn will only chup once.
Power Door Lock Switch Locking
If any door is open when the power door lock switch is
pressed, the system goes into an armed wait mode,
waiting for the doors to close. Once they are closed, the
system will
arm and the parking lamps will flash. If both
doors are closed when the lock switch
is pressed, the
system assumes you are inside the vehicle,
so it will not
arm. Note: Locking the doors by using the manual door
locks will not
arm the system.
2-15

Passive Arming
If the ignition was just turned off and a door was
opened, the system will arm six seconds after both doors
are closed, whether or not you lock them. In all other
cases, the system will wait
30 seconds after both doors
are closed before arming, allowing you time to get into
the vehicle and put the key in the ignition. The parking
lamps will flash when the system
arms. Passive arming
is not enabled from the factory.
Disarming the System
There are two ways to disarm the system:
Press the UNLOCK button on the remote keyless
entry transmitter. If the
horn chqs two or three
times when
you unlock the car, the alarm sounded in
your absence.
Two chirps means that the shock
sensor was set
off and three chqs means that a door
or hatch
was opened.
0 Turn the ignition to RUN with the proper key.
For more information on customizing the features
mentioned here, see “Feature Customization” in
the Index.
’hrning Off the Alarm
If you started the alarm by pressing the panic button on the
remote keyless entry transmitter, you must either push that
button again or
turn the ignition to RUN to stop the alarm.
If the alarm is sounding due to the shock sensor or a
door or hatch opening, it can be turned
off by either
turning the ignition with
a proper key inserted or by
pressing any button on the remote keyless entry
transmitter. If you use your remote keyless entry
transmitter
to silence the alarm, additional things will
happen depending upon which button you press.
Pressing the UNLOCK button will turn the alarm
off, unlock the driver’s door and dism the system.
Pressing the LOCK button will turn the alarm off,
keep the doors locked and keep the system armed.
Pressing the REAR 2X button twice will turn the
alarm off. A second push of the button (within five
seconds) will unlock
and disarm the hatch only.
0 Pressing the panic button will turn the alarm off,
keep the doors locked and keep the system armed.
If the
alarm is sounding because an incorrect ignition
key was used, press
any button on the remote keyless
entry transmitter to
turn the alarm off.
The alarm will stop by itself after two minutes.

To program features, your vehicle must be in the
programming mode. Follow these steps:
1. Put your key
in the ignition.
2. Turn the ignition to RUN to disarm the Content
Theft-Deterrent System.
3. Turn the ignition to OFF.
4. Remove the RADIO fuse. This fuse is in the main
fuse block, located on the left side of your
instrument panel. See “Fuses and Circuit Breakers”
in the Index.
5. Turn the ignition to ACC.
You should hear a chime to verify that the system is
in the programming mode. If the chime sounds once,
you will be able to program Exit Lighting, Delayed
Illumination, Last Door Closed Locking and Lockout
Prevention only.
If the chime sounds twice and your
vehicle is equipped with the Content Theft-Deterrent
System, you will also be able to program Remote
Keyless Entry Lock Control Verification, Arming
Method, Arming Verification, Driver’s Door Delay and Shock Sensor Enable.
Exit Lighting and Delayed Illumination
With Exit Lighting, your interior lamps will come
on for up to
25 seconds when the key is removed
from the ignition.
With Delayed Illumination, your interior lamps will stay on for up to
25 seconds when entering your vehicle and
up to five seconds when leaving your vehicle.
Your vehicle comes with both features enabled (Mode 4).
To change the factory setting, do the following:
1.
2.
3.
4.
Turn the courtesy lamps on by turning the instrument
panel brightness control knob all the way up.
Count the number of chimes you hear. The number
of chimes tells you which mode your vehicle is
set for.
Turn the courtesy lamp switch to
off.
Turn the courtesy lamp switch from on to off until
you hear the number of chimes that correspond to the
mode selection you want.
Mode 1: Both Off
Mode 2: Delayed Illumination Only
Mode 3: Exit Lighting Only
Mode 4: Both On

Last Door Closed Locking and
Lockout Prevention
Your vehicle comes with this feature set in Mode 2. To
change the factory setting, do the following:
1. Press the LOCK switch
on the door.
2. Count the number of chimes you hear. The number of
chimes tells you which mode your vehicle is set for.
3. Press the LOCK switch on the door until you hear
the number
of chimes that correspond to the mode
selection you want.
These features are designed to help prevent your keys
from being locked in your vehicle.
Mode 1: Both Off (Doors will lockhnlock when you
press the power door lock switch.)
Mode 2: Lockout Prevention Only (If you leave your keys
in the ignition and get out the driver’s door, you won’t be
able to lock the doors with the power door lock switch.)
Mode 3: Last Door Closed Locking Only (If the power
door lock switch is used to lock the vehicle while any
door is open, you will hear three chimes. The doors will
not lock until after all doors are closed.)
Mode 4: Both On (This combines Mode 2 and 3.)
Remote Keyless Entry Lock Verification
Your vehicle comes with this feature set in Mode 5. To
change the factory setting, do the following:
1. Press the UNLOCK button on the remote keyless
entry transmitter.
2. Count the number of chimes you hear. The number
of chimes tells you which mode your vehicle is
set for.
3. Press the UNLOCK button on the remote keyless
entry transmitter until you hear the number
of
chimes that corresponds to the mode selection
you want.
This feature provides feedback when the vehicle
receives a command from the remote keyless
entry transmitter.

Mode 1: All Off (The headlamps will not flash and the
horn
will not sound to provide you feedback that a
lockhnlock command has been received by the remote
keyless entry transmitter.)
Mode 2: Horn and Lamps/Lamps (Your horn will sound
briefly and your parking lamps will flash when you press
LOCK on the remote keyless entry transmitter. Only your parking lamps will flash when you press UNLOCK.)
Mode 3: Horn and Lamps (Your horn will sound briefly
and your parking lamps will flash every time you press
LOCK or UNLOCK.)
Mode 4: Lamps (Your parking lamps will flash every
time you press LOCK or UNLOCK.)
Mode 5: LampdHorn and LampdLamps (Your lamps will
flash upon the first press on LOCK, your lamps will flash
and your horn will sound upon the second press on LOCK
and your lamps will flash upon any press on
UNLOCK.)
Theft-Deterrent Arming Method
Your vehicle comes with this feature set in Mode 3. To
change the factory setting,
do the following:
1. Press the UNLOCK switch on the door.
2. Count the number of chimes you hear. The number
of chimes tells you which mode your vehicle is
set for.
3. Press the UNLOCK switch on the door until you
hear the number of chimes that correspond to the
mode selection you want.
Mode 1: Alarm System Off (The system will not arm.)
Mode 2: Remote Keyless Entry Transmitter Lock
(When you lock your doors using the remote keyless
entry transmitter, the system will arm itself.)
Mode 3: Remote Keyless Entry TransmitterPower
Door Lock Switch
(If you use either the remote keyless
entry transmitter or the power
door lock switch to lock
the doors, the system will
arm itself.)
Mode 4: Passive Arming and Remote Keyless Entry
TransmitterPower Door Lock Switch Arming (The
system will
arm itself after all doors are closed plus
arming per Mode
3).
2-21

Theft-Deterrent Arming Verification
Your vehicle comes with this feature set in Mode 3. To
change the factory setting, do the following:
1. Press the LOCK button on the remote keyless
entry transmitter.
2. Count the number of chimes you hear. The number of
chimes
tells you which mode your vehicle is set for.
3. Press the LOCK button on the remote keyless entry
transmitter until you hear the number of chimes that
corresponds to the
mode selection you want.
Mode 1: All Off (No horn chrrps or parking lamp flash.)
Mode 2: Horn and Lamps (Your parking lamps will
flash and your horn will chirp twice to verify the system
is armed using any arming method.)
Mode 3: Horn and LampsLamps (If you use the remote
keyless entry transmitter to
arm the system, your
parking lamps will flash and your horn will chup twice
to verify that the system is armed.
If it only chqs once,
the hatch is open or unlatched. If you use either the
power door lock switch or passive arming, only your
lamps will flash for verification.)
Mode 4: Lamps (When your vehicle arms, only your
parking lamps will flash for verification.)
Driver’s Door Alarm Delay and Shock
Sensor Enable
Your vehicle comes with this feature set in Mode 4. To
change the factory setting, do the following:
1. Turn the parking lamps on and off.
2. Count the number of chimes you hear. The number of
chimes
tells you which mode your vehicle is set for.
3. Turn the parking lamps on and off until you hear the
number of chimes that corresponds to the mode
selection you want.
Mode 1: Zero Delay and Shock Sensor Disabled (The
alarm will sound immediately if the driver’s door is
opened with your key and the shock sensor will not be
available to measure sharp blows to your vehicle.)
Mode 2: Eight-Second Delay and Shock Sensor
Disabled (The
alarm will sound eight seconds after the
driver’s door is opened with your key and the shock
sensor will not be available to measure sharp blows to
your vehicle.)
2-22

If you are towing a trailer and are parking on any hill,
see “Towing a Trailer” in the Index. That section shows
what to do first to keep the trailer from moving.
Windows
Manual Windows
Turn the window crank handle to open and close each
door window.
Power Windows (If Equipped)
Switches on the driver’s door control each window
when the ignition is on or when
RAP is present.
(See “Retained Accessory Power” in the Index.)
You can open the passenger’s window any amount by
pressing the switch and releasing it when the window
has lowered to the position you want.
The driver’s window has an auto-down feature. This
switch is labeled AUTO. Tap the bottom of the switch
and the driver’s window will open a small amount.
If the
rear of the switch is pressed all the way down and
released, the window will
go all the way down.
To stop the window while
it is lowering, press the top of
the switch.
To raise the window, press and hold the top
of the switch.
Horn
To sound the horn, press either horn symbol on your
steering wheel.
If your horn sounds two or three chirps when unlocking
your vehicle
with the optional remote keyless entry
transmitter, the
alarm was triggered while you were
away. Check the vehicle before entering.
2-45

Interior Lamps
Instrument Panel Brightness Control
This switch controls the brightness of your
instrument panel lights. Turn the switch to brighten or
dim the lights.
If you turn the switch all the way up,
your courtesy lamps will come on.
Courtesy Lamps
When either door is opened, several interior lamps go
on. These lamps are courtesy lamps. They make it easier
for you to enter and leave your vehicle.
Courtesy lamps include the dome lamp and other lamps
throughout
the interior of your vehicle.
To prevent battery rundown, your interior lamps will be
disabled about
10 minutes after the ignition is turned to
OFF. The 10-minute timer will be restarted if you do
any of the following:
1. Turn the ignition on.
2. Open either door.
3. Press any button on your remote keyless entry
transmitter.
4. Turn the interior lamp switch from off to on.
5. Open the hatch.
Delayed Illumination
With delayed illumination, the courtesy lamps will stay
on for
25 seconds after you close the doors when
entering the vehicle. They will stay on for five seconds
after you close the doors when exiting the vehicle. The
times will be shortened if the ignition is turned
to RUN
or if the power locks are activated. To turn this feature
on or off, see “Feature Customization”
in the Index.
Exit Lighting
With exit lighting, the interior lamps will come on when
you remove the key from the ignition to help you see
while exiting the vehicle. To turn this feature on or
off,
see “Feature Customization” in the Index.
2-55