1998 OLDSMOBILE INTRIGUE lock

I
A vehicle can fall from a car carrier if it isn’t
adequately secured. This can cause a collision,
serious personal injury and vehicle damage. The
vehicle should be tightly secured with chains or
steel cables before it is transported.
Don’t use substitutes (ropes, leather straps,
canvas webbing, etc.) that can be cut by sharp
edges underneath the towed vehicle.
Always use
T-hooks inserted in the T-hook slots. Never use
J-hooks. They will damage drivetrain and
suspension components.
When your vehicle is being towed, have the ignition key
turned to the OFF position. The steering wheel should
be clamped in a straight-ahead position, with a clamping
device designed for towing service.
Do not use the
vehicle’s steering column lock for this. For front towing,
the transaxle should be in
PARK (P) and the parking
brake released. For rear towing, the transaxle should be
in
NEUTRAL (N) and the parking brake engaged.
Don’t have your vehicle towed on
the drive wheels,
unless you must.
If the vehicle must be towed on the
drive wheels, be sure to follow the speed and distance
restrictions later in this section
or your transaxle will be
damaged. If these limitations must be exceeded, then the
drive wheels have to be supported on
a dolly.
5-10
ProCarManuals.com

How to Add Coolant to the Radiator
NOTICE:
Your engine has a specific radiator fill procedure.
Failure to follow this procedure could cause
your
engine to overheat and be severely damaged.
1. You can remove the radiator pressure cap when
the cooling system, including the radiator pressure
cap and upper radiator hose, is no longer hot. Turn
the pressure cap
slowly counterclockwise until it
first stops. (Don't press down while turning the
pressure cap.)
If
you hear a hiss, wait for that to stop. A hiss means
there is still some pressure left.
5-21
ProCarManuals.com

Changing a Flat Tire
If a tire goes flat, avoid further tire and wheel damage
by driving slowly
to a level place. Turn on your hazard
warning flashers.
Changing a tire can cause an injury. The vehicle
can slip off the jack and roll over you or other
people. You and they could be badly injured.
Find a level place to change your tire.
To help
prevent the vehicle from moving:
1. Set the parking brake firmly.
2. Put the shift lever in PARK (P).
3. Turn off the engine.
To be even more certain the vehicle won’t move,
you can put blocks at the front and rear of the
tire farthest away from the one being changed.
That would be the tire on the other side of the
vehicle, at the opposite end.
i
The following steps will tell you how to use the jack and
change a
tire.
5-25
ProCarManuals.com

Storing the Spare Tire and Tools
Storing a jack, a tire or other equipment in the
passenger compartment
of the vehicle could
cause injury. In a sudden stop or collision, loose
equipment could strike someone. Store all these
in the proper place.
~
The compact spare is for temporary use only. Replace
the compact spare tire with a full-size tire as
soon as you
can. See “Compact Spare Tire” in the Index. See the
storage instructions label
to replace your compact spare
into your trunk properly.
1. Retainer
2. Cover
3. Retainer (Position only
for full-size spare)
4. Tire
5. Nut
6. Jack
7. Wrench
8. Lock Nut Tool
9. Foam Holder
10. Bolt Screw
1 1. Extension and
Protector/Guide
5-34
ProCarManuals.com

The switch for the fuel
door is on the instrument
panel, to the left of the
steering column.
If your fuel filler door release won’t operate, there is a
manual release tab. The tab
is located against the trim on
the driver’s side of the vehicle,
in the trunk.
I
The cap is behind a hinged door on the left side of your
vehicle. While refueling, hang the cap by the tether from
the pin on the filler door.
To remove the cap, turn it slowly to the left
(counterclockwise). The cap has a spring in it; if you let
go of the cap too soon, it will spring back to the right.
6-6
ProCarManuals.com

If you get gasoline on yourself and then
something ignites it, you could be badly burned.
Gasoline can spray out on you if you open the
fuel filler cap too quickly. This spray can happen
if your tank is nearly full, and is more likely in
hot weather. Open the fuel filler cap slowly and
wait for any “hiss” noise to stop. Then unscrew
the cap all the way.
Be careful not to spill gasoline. Clean gasoline from
painted surfaces as soon as possible. See “Cleaning the
Outside of Your Vehicle” in the Index. When
you put the cap back on, turn it to the right
(clockwise) until you hear a clicking sound. Make sure
you fully install the cap. The diagnostic system can
determine
if the fuel cap has been left off or improperly
installed. This would allow fuel to evaporate into the
atmosphere. See “Malfunction Indicator Lamp” in
the Index.
NOTICE:
If you need a new cap, be sure to get the right
type. Your retailer can get one for you.
If you get
the wrong type, it may not fit properly. This may
cause your malfunction indicator lamp to light
and your fuel tank and emissions system may be
damaged. See “Malfunction Indicator Lamp” in
the Index.
6-7
ProCarManuals.com

If you find that the headlamp aiming needs adjustment,
follow these steps:
A. Horizontal aim adjustment screw
B. Vertical aim adjustment screw
1. Start by opening the hood and locating the vertical
and horizontal aim indicators. The aiming screw for
the horizontal aim indicator is on the outboard side
of the headlamp cover
(A) and the aiming screw for
the vertical aim indicator
is on the inboard side (B).
NOTICE:
Horizontal aim of the headlamp must be done
first. Adjusting vertical aim first will result in
incorrect headlamp aim.
B. Vertical aim adjustment screw
C. Horizontal block index plate
D. Vertical aiming level
6-35
ProCarManuals.com

2. Using an E8 torx socket, turn the horizontal aiming
adjustment screw
(A) until the “0” (zero) on the
pointer
is lined up with the center marking on the
3.
1.
-
horizontal block index plate (C).
To adjust the vertical aim, use an E8 torx socket
and turn the vertical aiming adjustment screw
(B)
until the bubble inside the level (D) is centered at
“0” (zero).
Front Parking, Sidemarker and Turn Signal
Cornering Lamp
Remove the headlamp assembly. Refer to the
removal procedure earlier in this section.
2.
3.
4.
5.
6.
Remove the rubber bulb access cover.
Twist and pull each bulb socket from the
headlamp assembly.
Holding the base
of the bulb, pull the bulb from
the socket.
Push the new bulb into the socket.
Put the bulb socket back into the headlamp assembly
and
turn it to the right until it is secure.
Redace the rubber bulb access cover.
I
Center High-Mounted Stoplamp
1. Open the trunk.
Lr
2. Reach through the access opening in the trunk.
3. Remove the bulb by turning it one-quarter of a turn
to the left.
6-36
ProCarManuals.com