1998 OLDSMOBILE BRAVADA light

The liftgate and glass will automatically lock when shut.
To
lock the power lock system from the outside, insert
the key
in the lock button and turn it to the right. All
doors will lock.
Remote Liftgate Glass Release
This button on the
passenger’s side
of the
steering column allows you
to release the liftgate glass
from inside
the vehicle.
Key in the Ignition
If you leave your vehicle with the keys inside, it’s an
easy target for joy riders or professional thieves
-- so
don’t do it.
When you park your vehicle and open the driver’s door,
you’ll hear
a tone reminding you to remove your key
from the ignition
and take it with you. Always do this.
Your steering wheel
will be locked, and so will your
ignition and transmission. And remember to lock
the doors.
Parking at Night
Park in a lighted spot, close all windows and lock your
vehicle. Remember
to keep your valuables out of sight.
Put
them in a storage area, or take them with you.
Your shift lever must be
in PARK (P) or NEUTRAL (N)
for the release to work.
Theft
Vehicle theft is big business, especially in some cities.
Although your vehicle
has a number of theft-deterrent
features, we know that nothing we put
on it can make it
impossible to steal. However, there are ways you can help.
Parking Lots
If you park in a lot where someone will be watching
your vehicle, it’s best to lock
it up and take your keys.
But what
if you have to leave your ignition key‘? What if
you have to leave something valuable in your vehicle?
Put your valuables in a storage area, like your
glove box.
0 Lock all the doors except the driver’s.
2-10
ProCarManuals.com

Passlock TM
Your vehicle is equipped with the Passlock
theft-deterrent system.
Passlock
is a passive theft-deterrent system. The system
is armed once the
key is removed from the ignition.
Passlock enables fuel if the ignition lock cylinder
is
turned with a valid key. If a correct key is not used, fuel
is disabled.
During normal operation, the SECURITY light will go
off after the engine is started.
If the engine stalls and the SECURITY light flashes,
wait about
10 minutes until the light stops flashing
before trying to restart the engine. Remember to release
the key from the START position
as soon as the
engine starts.
If the engine does not start after three (3) tries, the
vehicle needs service.
If you are driving and the SECURITY light comes on,
you will be able to restart the engine if you turn the
engine off. However, your Passlock system is not
working properly and must be serviced by your retailer.
Your vehicle is not protected by Passlock at this time.
You may
also want to check the fuse (see “Fuses
and Circuit Breakers” in the Index). See your retailer
for service.
If the SECURITY light comes on while the engine is
running, a problem has been detected and the system
may need service. See your retailer for service.
In an emergency, call the Oldsmobile Roadside
Assistance Center at
1 -800-442-OLDS (6537).
ProCarManuals.com

Parking Brake
To set the parking brake, hold the regular brake pedal
down
with your right foot. Push down the parking brake
pedal with your left foot.
If the ignition is on, the brake
system warning light
will come on.
To release the parking brake, hold the reg~dar brake
pedal down.
I NOTICE:
~
Driving with the parking brake on can cause
your rear brakes to overheat. You may have to
replace them, and you could also damage other
parts
of your vehicle.
If you are towing a trailer and you must park on a hill,
see “Towing a Trailer” in the Index. That section shows
what to do first to keep the trailer fl-om moving.
Pull the BRAKE RELEASE lever. It is located on the
bottom
of the instrument panel on the driver‘s side.
2-19
ProCarManuals.com

Windows
Power Windows
The power windows controls are on each of the side
doors. With power windows, the switches control the
windows when the ignition is on or when Retained
Accessory Power (RAP) is present. (See "Retained
Accessory Power"
in the Index.') The driver's door has
a switch for the passenger windows as well. There
are individual controls
on each of the side doors.
Press the side of the switch with the down arrow to
lower a window. Press the side of the switch with the up
arrow
to raise a window.
Express-Down Window
The driver's window switch has an express-down
feature
that allows you to lower it without holding the
window switch. Hold the driver's window switch down
,for more than half a second to activate the express-down
feature. Lightly tap the switch
to open the window
slightly. The express-dawn feature can be interrupted
at any time by pressing the up arrow end of the switch.
Lockout Switch
Your vehicle has a lockout feature to prevent passengers
fro111 operating the power windows. Press LOCK to
activate this feature. Press NORM and the windows
return
to norrnal operation.
Horn
To sound the horn. press the center pad on the
steering wheel.
2-25
ProCarManuals.com

Turn and Lane Change Signals
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow
you to signal
a turn or a lane change.
To signal
a turn, move the lever all the way up or down.
When
the turn is finished. the lever will return automatically.
An arrow on the
instrument panel
will
flash in the direction of
the
turn or lane change.
To signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return by
itself when you release
it.
As you signal a turn or a lane change, if the arrows don't
flash but just stay on,
a signal bulb may be burned out
and other drivers won't see your
turn signal.
If a bulb is burned out, replace it to help avoid an
accident.
If the arrows don't go on at all when you
signal
a turn, check the fuse (see "Fuses and Circuit
Breakers''
in the Index) and for burned-out bulbs.
If you have a trailer towing option with added wiring for
the trailer lamps,
a different turn signal flasher is used.
With this flasher installed, the signal indicator
will flash
even
if a turn signal bulb is burned out. Check the front
and rear
turn signal lamps regularly to make sure they
are working.
Turn Signal On Chime
If your turn signal is left on for nwre than 3/4 of a mile
( I .2 km), a chime will sound at each flash of the turn
signal. To
turn off the chime., move the turn signal lever
to the
off position.
Headlamp High/Low Beam Changer
To change the headlamps from low to high beam or high
to low beam.
pull the multifunction lever a11 the way
toward you. Then release
it.
When the high beams are
on, this indicator light
on
the instrument panel will
also be on.
ProCarManuals.com

Windshield Wipers
I-
You control the windshield wipers by turning the band
with
the wiper symbol on it.
For a single wiping cycle, turn the band to MIST. Hold
it there until the wipers start, then let go. The wipers will
stop after
one wipe. If you want more wipes, hold the
band
on MIST longer.
rcm
can set the wiper speed for a long or short delay
between wipes. This can be very useful
in light rain or
snow. Turn the band
to choose the delay time. The
closer
to LO, the shorter the delay. For steady
wiping at
low speed, turn the band away
from
you to LO. For high-speed wiping, turn the
band further, to HI. To stop the wipers, rnove the
band
to OFF.
Be sure to clear ice and snow from the wiper blades
before using them.
If they’re frozen to the windshield,
carefully loosen
or thaw them. IF your blades do become
worn
or damaged, get new blades or blade inserts.
Windshield Washer
There‘s a paddle marked with the windshield washer
symbol
on the top of the rnultifunction lever. To spray
washer fluid
on the windshield, push the paddle. The
wipers
will clear the window and then either stop or
return to your preset speed.
In freezing weather, don’t use your washer until
the windshield
is warmed. Otherwise the washer
fluid can form ice on the windshield, blocking
your vision.
2-28
-
ProCarManuals.com

Increasing Speed While Using Cruise Control
There are two ways to go to a higher speed:
0 Use the accelerator pedal to get to the higher speed.
Press the button
at the end of the lever: then release
the button
and the accelerator pedal. You’ll now
cruise at the higher speed.
Move the cruise switch from ON to R/A. Hold it
there until you get up to the speed you want, and
then release the switch.
(To increase your speed in
very small amounts, move the switch to R/A. Each
time you do this. your vehicle
will go about 1 mph
( 1.6 km/h) faster.)
Reducing Speed While Using Cruise Control
Press in the button at the end of the lever until you
reach the lower speed you want, then release
it.
0 To slow down in very small amounts, press the
button for less than half
a second. Each time you do
this, you‘ll go I mph ( I .6 kdh) slower.
Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase your speed. When
you take your foot
off the pedal, your vehicle will slow
down to the cruise control speed you set earlier.
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed,
load and the steepness of the hills.
When going up steep hills, you may want to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear
to keep your speed down. Of course, applying the brake
takes you out of cruise control. Many drivers find this to
be too much trouble and don’t use cruise control
on
steep hills.
Ending Cruise Control
There are two ways to turn off the cruise control:
0 Step lightly on the brake pedal.
0 Move the cruise switch to OFF.
Erasing Speed Menwry
When you turn off the cruise control or the ignition,
your cruise control set speed memory
is erased.
2-3 1
ProCarManuals.com

Exterior Lamps
Your parking lamp and headlamp switch is on the
driver’s side
of your instrument panel.
Rotate the knob to the right to the parking lamps symbol
to manually turn on:
Parking Lamps
Sidemarker Lamps
Tidillamps
0 License Plate Lamps
Instrument .Panel Lights Rotate
the knob
to the right to the master lamp symbol
to turn on all the lamps listed as well as the headlamps.
Rotate the knob all the way to the left to turn
off your
lamps and put the system
in auto headlamp mode.
Automatic Headlamp System
When it is dark enough outside, your automatic
headlamp system will turn on your headlamps at the
normal brightness along
with other lamps such as the
taillamps, sidemarker, parking lamps and the instrument
panel lights. The radio lights
will also be dim.
Your vehicle is equipped with a light sensor
on the top
of the instrument panel under the radio speaker grill, so
be sure it is not covered, which will cause the system to
be on whenever the ignition
is on.
The system may also turn on your lights when driving
through a parking gzage, heavy overcast weather, a tunnel
or fueling your vehicle in a low-light area. This is normal.
There is
a delay in the transition between the daytime and
nighttime operation
of the Daytime Running Lamps
(DRL) and the automatic headlamp systems
so that driving
under bridges or bright overhead street lights does not
afiect the system. The DRL and automatic headlamp
system
will only be affected when the light sensor sees a
change
in lighting lasting longer than the delay.
2-32
ProCarManuals.com