1998 MITSUBISHI MONTERO torque

DIAGNOSTIC TROUBLE CODE IDENTIFICATION
DIAGNOSTIC TROUBLE CODE IDENTIFICATION








\









\









\









\









\









\









\







DTC ( 1) Probable Cause
11 ........................ Defective TP Sensor Or TP Sensor Circuit
15 ............................. Open Oil Temperature Sensor Circuit
16 ............................ Short Oil Temperature Sensor Circuit
21 ................................... Short Ignition Signal Circuit
22 .................................... Open Ignition Signal Circuit
23 .......................... Open Signal Line (ECT) From ECM To TCM\
24 ......................... Short Signal Line (ECT) From ECM To TCM\
29 ............................. Short Neutral Safety Switch Circuit
30 .............................. Open Neutral Safety Switch Circuit
31 ................................. Open No. 2 Speed Sensor Circuit
32 ................................. Open No. 1 Speed Sensor Circuit
41 ..................................... Open Solenoid No. 1 Circuit
42 .................................... Short Solenoid No. 1 Circuit
43 ..................................... Open Solenoid No. 2 Circuit
44 .................................... Short Solenoid No. 2 Circuit
47 ................................... Open Lock-Up Solenoid Circuit
48 .................................. Short Lock-up Solenoid Circuit
49 .............. ( 2) Torque Converter Clutch Engagement Malfunction
50 ........... ( 2) Torque Converter Clutch Disengagement Malfunction
51 ................................. 1st Gear Ratio Signal Incorrect
52 ................................. 2nd Gear Ratio Signal Incorrect
53 ................................. 3rd Gear Ratio Signal Incorrect
54 ................................. 4th Gear Ratio Signal Incorrect
( 1) - Check listed fault code and component for probable cause. See
appropriate fault code listing under DIAGNOSTIC TESTS. Check
wiring and connections of specified component.
( 2) - Scan tool is required for testing malfunctioning circuit.









\









\









\









\









\









\









\







Fig. 6: Identifying Data Link Connector (DLC) Terminals
Courtesy of Mitsubishi Motor Sales of America.

voltage should be .3-2.5 volts.
3) If voltage is as specified, go to next step. If voltage is
not as specified, replace the output speed sensor. If DTC still
exists, check speed sensor rotor. See MITSUBISHI R4AW3 & V4AW3
OVERHAUL article. If DTC exists after speed sensor rotor is replaced,
check for noise interference and repair.
4) Check and repair wiring harness and connectors between
output speed sensor and TCM. If wiring is okay, recheck DTCs. If DTCs
still exists, replace TCM.
DTC 41 & 42: OPEN OR SHORT IN SOLENOID NO. 1 CIRCUIT
NOTE: A stuck solenoid will not set a DTC. DTCs are only set for
circuit malfunctions, not mechanical failures.
1) Disconnect solenoid and sensor connector. Using ohmmeter,
check resistance between solenoid connector terminal No. 6 and ground.
See Fig. 9 . Resistance should be 11-15 ohms at 77
F (25C). If
resistance is as specified, go to next step. If resistance is not as
specified, replace solenoid No. 1 and recheck DTC.
2) Check wiring harness and connectors between solenoid No. 1
and TCM. If wiring and solenoid No. 1 is okay, replace TCM.
DTC 43 & 44: OPEN OR SHORT IN SOLENOID NO. 2 CIRCUIT
NOTE: A stuck solenoid will not set a DTC. DTCs are only set for
circuit malfunctions, not mechanical failures.
1) Disconnect solenoid and sensor connector. Using ohmmeter,
check resistance between solenoid connector terminal No. 7 and ground.
See Fig. 9 . Resistance should be 11-15 ohms at 77
F (25C). If
resistance is as specified, go to next step. If resistance is not as
specified, replace solenoid No. 2 and recheck DTC.
2) Check wiring harness and connectors between solenoid No. 2
and TCM. If wiring and solenoid No. 2 is okay, replace TCM.
DTC 47 & 48: OPEN OR SHORT IN LOCK-UP SOLENOID CIRCUIT
NOTE: A stuck solenoid will not set a DTC. DTCs are only set for
circuit malfunctions, not mechanical failures.
1) Disconnect solenoid and sensor connector. Using ohmmeter,
check resistance between solenoid connector terminal No. 8 and ground.
See Fig. 9 . Resistance should be 11-15 ohms at 77
F (25C). If
resistance is as specified, go to next step. If resistance is not as
specified, replace lock-up solenoid and recheck DTC.
2) Check wiring harness and connectors between lock-up
solenoid and TCM. If wiring and lock-up solenoid is okay, replace TCM.
DTC 49: TORQUE CONVERTER CLUTCH (TCC) ENGAGEMENT MALFUNCTION
1) Using scan tool, verify vehicle tachometer and scan tool
vehicle RPM values are identical. If tachometer values are identical,
go to next step. If tachometer values are different, test ignition
signal circuit. See DTC 21 & 22: SHORT OR OPEN IN IGNITION SIGNAL
CIRCUIT.
2) Lift and support vehicle to allow drive wheels to spin
freely. With transmission in "D" position, run engine to 1300-1900
RPM. Verify scan tool and speedometer read 31 MPH (50 km/h). If values\
are identical, go to next step. If values are different, test input
speed sensor. See DTC 31: INPUT SPEED SENSOR.
3) Check lock-up solenoid for proper operation. See SOLENOIDS

If DTC 51 is set also, go to DTC 51: 1ST GEAR RATIO SIGNAL
INCORRECT test. If DTC 51 is not set, check overdrive brake for a
mechanical failure. See OVERDRIVE BRAKE in MITSUBISHI R4AW3 & V4AW3
OVERHAUL article.
SYMPTOM TROUBLE SHOOTING
NOTE: Check system using appropriate scan tool. See WIRING DIAGRAMS
for electrical schematics and COMPONENT TESTING.
COMMUNICATION WITH SCAN TOOL NOT POSSIBLE
If scan tool cannot communicate with TCM, check proper
connection with DLC. Check TCM power circuits, TCM ground circuits and
malfunctioning TCM.
SHIFT POINTS INCORRECT
If shift points are incorrect, check for DTCs. If no DTC is
present, check oil temperature sensor, pattern select switch, 4WD low
range detection switch and TCM for proper operation.
UPSHIFTS OCCUR SPONTANEOUSLY
If upshifting occurs spontaneously, check park/neutral
position switch, overdrive switch and TCM for proper operation.
TCC LOCK-UP MALFUNCTIONING
If TCC lock-up system is not operating properly, check torque
converter, valve body, lock-up switch and oil temperature switch.
COMPONENT TESTING
A/T FLUID TEMPERATURE SWITCH
1) Remove fluid temperature switch, located to rear of
neutral safety switch. Immerse switch in container of ATF up to top
threaded portion of switch. Using a DVOM, check continuity between
switch terminals. Continuity should not exist when fluid temperature
is 257
F (125C) or less.
2) When fluid is heated to 289-304F (143-151C), continuity
should exist. Replace switch if necessary. Apply thread sealant to
fluid temperature switch threads and install in transmission.
BRAKELIGHT SWITCH
1) Disconnect electrical connector from brakelight switch,
located near brake pedal. Using ohmmeter, ensure continuity exists
between terminal No. 2 (White/Red wire) and terminal No. 3 (Green
wire) with brake pedal released. Replace brakelight switch if
continuity does not exist. Continuity should not exist between
terminals No. 2 and No. 3 with brake pedal depressed.
2) If continuity does not exist, ensure brake pedal is
properly adjusted so brakelight switch has proper travel for switch
operation. If proper brakelight switch travel exists, replace
brakelight switch.
ENGINE COOLANT TEMPERATURE (ECT) SENSOR

Disconnect electrical connector from output speed sensor. See
Fig. 15. Remove bolt and output speed sensor. To install, reverse
removal procedure.
Fig. 15: Locating Output Speed Sensor & Connector
Courtesy of Mitsubishi Motor Sales of America.
PARK/NEUTRAL POSITION (PNP) SWITCH
Removal
Switch is located on side of transmission. Remove manual
lever from control shaft on transmission. Bend up tabs on lock washer.
Remove lock nut, lock washer and seal from control shaft. Remove
retaining bolt and neutral safety switch.
Installation
1) Install switch on control shaft. Loosely install switch
retaining bolt. Install seal and lock washer. Install lock nut and
tighten to specification. See TORQUE SPECIFICATIONS.
2) Switch must be adjusted. Ensure parking brake is applied.
Temporarily install manual lever on control shaft. Place shift lever
in Neutral. Remove manual lever. Rotate switch and align reference
mark on switch with groove.
3) Hold switch in this position. Tighten retaining bolt to
specification. Bend tabs on lock washer over against lock nut. To
install remaining components, reverse removal procedure.

SOLENOIDS
Removal & Installation
Solenoids are located on transmission valve body. See Fig. 3.
Remove bolt, solenoid and gasket from valve body. To install, reverse
removal procedure.
THROTTLE POSITION SENSOR
NOTE: For removal and installation information, see appropriate
SELF-DIAGNOSTICS article in ENGINE PERFORMANCE section.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS








\









\









\









\









\









\









\







Application INCH Lbs. (N.m)\
Park/Neutral Switch Bolt .................................. 48 (5.4)\
Park/Neutral Switch Lock Nut .............................. 35 (4.0)\









\









\









\









\









\









\









\







WIRING DIAGRAMS

AUTO TRANS DIAGNOSIS
1998 Mitsubishi Montero
1997-98 AUTOMATIC TRANSMISSIONS
Mitsubishi Shift Lock Systems
Diamante, Eclipse, Galant, Mirage, Montero, Montero Sport,
3000GT
DESCRIPTION
Shift interlock system inhibits shift selector lever movement
from "P" to drive ranges unless brake pedal is depressed. Key
interlock system prevents ignition switch turning to LOCK position
unless shift selector lever is in "P" position.
TESTING
KEY INTERLOCK SYSTEM
1) With ignition switch in LOCK position and brake pedal
depressed, ensure selector lever cannot be moved from "P" to any other
position. Ensure selector lever button cannot be pushed. With ignition
switch in ACC position, brake pedal depressed and selector lever
button pushed, ensure selector lever can be moved from "P" position to
any other position. Ensure selector lever moves smoothly.
2) Ensure ignition key cannot be turned to LOCK position at
all selector lever positions other than "P". Ensure ignition key turns
smoothly to LOCK position when selector lever is set to "P" and
selector lever button is released. If key interlock system is not as
specified, adjust key interlock cable. See KEY INTERLOCK CABLE under
ADJUSTMENTS.
SHIFT LOCK SYSTEM
1) With ignition switch in ACC position, brake pedal released
and selector lever button pushed, ensure selector lever cannot be
moved from "P" to any other position. With ignition switch in ACC
position, brake pedal depressed and selector lever button pushed,
ensure selector lever can be moved from "P" position to any other
position.
2) With selector lever in "R" position, ignition switch in
ACC position, brake pedal released and selector button pushed, ensure
selector lever can be moved from "R" to "P" position. If shift lock
system is not as specified, adjust shift lock cable. See SHIFT LOCK
CABLE under ADJUSTMENTS.
ADJUSTMENTS
KEY INTERLOCK CABLE
3000GT
Remove front console assembly. Move selector lever to "P".
Loosen nut securing key interlock cable. Gently press lock cam "A"
down while pushing cable to take up slack. See Fig. 1. Tighten nut to
specifications to secure cable. See TORQUE SPECIFICATIONS.

Fig. 1: Adjusting Key Interlock Cable (3000GT)
Courtesy of Mitsubishi Motor Sales of America.
Except 3000GT
Remove front console assembly. Move selector lever to "P".
Turn ignition switch to LOCK position. Loosen nut securing key
interlock cable. See Fig. 2. Gently push lock cam until pin stops in
direction of arrow. Tighten nut to specifications to secure cable. See
TORQUE SPECIFICATIONS. Install front console assembly.
Fig. 2: Adjusting Key Interlock Cable (Except 3000GT)
Courtesy of Mitsubishi Motor Sales of America.
SHIFT LOCK CABLE

3000GT
Remove front console assembly. Move selector lever to "P".
Loosen nuts securing shift lock cable and remove washer and cotter pin
at cable end. Turn lock cam counterclockwise to move set lever upward.
Fit cutout in set lever on pin of lock cam "B". Gently press set lever
down while pushing cable to take up slack. See Fig. 3. Tighten nut to
specifications to secure cable. See TORQUE SPECIFICATIONS. Ensure that
cable end contacts pin on lock cam, then install washer and cotter
pin.
Fig. 3: Adjusting Shift Lock Cable (3000GT)
Courtesy of Mitsubishi Motor Sales of America.
Except 3000GT
Remove front console assembly. Move selector lever to "P".
Loosen nuts securing shift lock cable. See Fig. 4. Adjust shift lock
cable so end of cable (Red mark) sits between lobe of lock cam, then
tighten nut to specifications to secure cable. See TORQUE
SPECIFICATIONS. Install front console assembly.