1998 MITSUBISHI MONTERO oil capacities

 FLUID CAPACITIES 
\b
\
\
\
\
\
\
\




Item  Condition  Specification (1) 
\b
\
 \
\
\
 \
\
\



Engine Oil  Oil Pan  4.5 Qts. (4.3L) 

(
1) \b \
\
\
 \
\



 Oil Filter  0.32 Qts. (0.3L) 

\b
\
\
\
 \
\



 Oil Cooler  0.32 Qts. (0.3L) 
\b
\
\
\
\
\
\
\



(
1) - Capacities are recommended or calculated levels. Always use 

dipstick to measure level. 
\f
\
\
\
\
\
\
\


120,000 MILE (200,000 KM) NORMAL SERVICE
120,000 MILE (200,000 KM) NORMAL SERVICE
\
\
\
\
\
\
\
 
VERIFY 
\b
\
\
\
\
\
\
\




Last Major Service Was Performed 
\b
\
\
\
\
\
\
\




SERVICE 
\b
\
\
\
\
\
\
\



 Ball Joints With Grease Nipple (
6) 
\b
 \
\
\
\
\
\
\



 Propeller Shaft Joints (
6) 
\b
\
\
\
\
\
\
\




INSPECT 
\b
\
\
\
\
\
\
\



 Fuel Hoses (
3) 
\b
 \
\
\
\
\
\
\



 Fuel System (Tank, Pipe Line, Connection & Fuel Tank Filler 

 Tube Cap) (
3) 
\b
 \
\
\
\
\
\
\



 Evaporative Emission Control System (Except Evaporative 

 Emission Canister) (
7) 
\b
 \
\
\
\
\
\
\



 Drive Belt (For Generator, Water Pump, Power Steering Pump) 
\b
 \
\
\
\
\
\
\



 Manual Transmission Oil 
\b
 \
\
\
\
\
\
\



 Transfer Oil 
\b
 \
\
\
\
\
\
\



 Disc Brake Pads (
4) 
\b
 \
\
\
\
\
\
\



 Brake Hoses (
4) 
\b
 \
\
\
\
\
\
\



 Ball Joint & Steering Linkage Seals (
3) 
\b
 \
\
\
\
\
\
\



 Drive Shaft Boots (
4) 
\b
 \
\
\
\
\
\
\



 Exhaust System (
3) 
\b
 \
\
\
\
\
\
\



 Distributor Cap & Rotor (
7) 
\b
\
\
\
\
\
\
\




REPLACE 
\b
\
\
\
\
\
\
\



 Engine Oil (
1) 
\b
 \
\
\
\
\
\
\



 Engine Oil Filter (
2) 
\b
 \
\
\
\
\
\
\


  Engine Coolant 
\b
 \
\
\
\
\
\
\



 Automatic Transmission Fluid 
\b
 \
\
\
\
\
\
\



 Rear Axle Oil 
\b
 \
\
\
\
\
\
\



 Spark Plugs 
\b
 \
\
\
\
\
\
\



 Timing Belt (
9) 
\b
 \
\
\
\
\
\
\



 Ignition Cables (
8) 
\b
 \
\
\
\
\
\
\



 Air Cleaner Filter 
\b
\
\
\
\
\
\
\



(
1) - Change once a year or every 7,500 miles (12,000 KM). 

(
2) - If mileage is less than 7,500 miles (12,000 KM) each year, 

replace the oil filter at every oil change. 

(
3) - Or inspect every 2 years. 

(
4) - Or inspect every year. 

(
5) - Or change every 2 years. 

(
6) - Or lubricate grease every 2 years. 

(
7) - Or inspect every 5 years. 

(
8) - Or replace every 5 years. 

(
9) - For California & Massachusettes, this maintenance is 

recommended but not required. 
\b
\
\
\
\
\
\
\




LUBRICATION SPECIFICATIONS 
\b
\
\
\
\
\
\
\




Material  Condition  Specification 
\b
\
 \
\
\
 \
\
\



Engine Oil  Ambient Temperature Less Than SAE 5W-30 

(
1)  0F (-18C) To 100F (38C)  

\b
\
\
\
 \
\



Ambient Temperature Above 0F  SAE 10W-30 

 (-18C) To Over 100F (38C)  
\b
\
 \
\
\
 \
\
\



Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 
\b
\
 \
\
\
 \
\
\



Manual  All API Classification GL-4

Transmission   SAE 75W-85W Or 75W-90 
\b
\
 \
\
\
 \
\
\



Automatic  All  "ATF DEXRON II" Or 

Transmission   Equivalent 
\b
\
 \
\
\
 \
\
\



Brake Fluid  All  DOT 3 Or DOT 4 
\b
\
 \
\
\
 \
\
\



Rear Axle  All API Classification GL-5

  Or Higher (
2) 
\b
\
 \
\
\
 \
\
\



Transfer Case All API Classification GL-4

  SAE 75W-85W Or 75W-90 
\b
\
\
\
\
\
\
\



(
1) - SAE 5W-30 engine oil is preferred. SAE 10W-30 may be used if 

the Ambient Temperature is above 0 F (-18 C). 

(
2) - SAE90, 85W-90, 80W-90 may be used in temperatures above 

-10 F (-23 C). SAE 80W, 80W-90 may be used in temperatures 

from -30 F (-34 C) to -10 F (-23 C). SAE 75W may be used 

in temperatures below -30 F (-34 C). 
\b
\
\
\
\
\
\
\




FLUID CAPACITIES 
\b
\
\
\
\
\
\
\


 Item  Condition  Specification (1) 
\b
\
 \
\
\
 \
\
\



Engine Oil  Oil Pan  4.5 Qts. (4.3L) 

(
1) \b \
\
\
 \
\



 Oil Filter  0.32 Qts. (0.3L) 

\b
\
\
\
 \
\



 Oil Cooler  0.32 Qts. (0.3L) 
\b
\
 \
\
\
 \
\
\



Engine  Drained; With Reserve Tank  10 Qts. (9.5L) 

Coolant   
\b
\
 \
\
\
 \
\
\



Automatic  Drained  8.9 Qts. (8.5L) 

Transmission   
\b
\
 \
\
\
 \
\
\



Manual  Drained  3.3 Qts. (3.2L) 

Transmission   
\b
\
 \
\
\
 \
\
\



Rear Axle  Drained  3.3 Qts. (3.2L) 
\b
\
 \
\
\
 \
\
\



Transfer Case Drained  2.6 Qts. (2.5L) 
\b
\
\
\
\
\
\
\



(
1) - Capacities are recommended or calculated levels. Always use 

dipstick to measure level. 
\f
\
\
\
\
\
\
\


LUBRICATION SPECIFICATIONS
LUBRICATION SPECIFICATIONS TABLE
\
\
\
\
\
\
\
 
Material  Condition  Specification 
\b
\
 \
\
\
 \
\
\



Engine Oil Ambient Temperature Less Than  SAE 5W-30 

(
1)  0F (-18C) To 100F (38C)  

\b
\
\
\
 \
\



Ambient Temperature Above 0F  SAE 10W-30 

 (-18C) To Over 100F (38C)  
\b
\
 \
\
\
 \
\
\



Power  All Automatic Transmission 

Steering   Fluid DEXRON II 

Fluid   
\b
\
 \
\
\
 \
\
\



Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 
\b
\
 \
\
\
 \
\
\



Transfer Case All API Classification GL-4

  SAE 75W-85W Or 75W-90 
\b
\
 \
\
\
 \
\
\



Front Axle  All API Classification GL-5

  Or Higher (
2) 
\b
\
 \
\
\
 \
\
\



Clutch Fluid  All  DOT 3 Or DOT 4 
\b
\
 \
\
\
 \
\
\



Hook Lock  All  Multipurpose Grease 

Catch, Door   NLGI Grade 2 

Lock Strikers  

Seat Adjust-   

ers, Backdoor  

Lock, Parking  

Brake Cable   

Mechanism   
\b
\
 \
\
\
 \
\
\


 Front Wheel  All  Multipurpose Grease 

Bearings   NLGI Grade 2 Or 

  Equivalent 
\b
\
 \
\
\
 \
\
\



Door Hinges, All  Engine Oil 

Back Door   

Hinges   
\b
\
 \
\
\
 \
\
\



A/C  All  HFC-134a 

Refrigerant   
\b
\
 \
\
\
 \
\
\



Manual  All API Classification GL-4

Transmission   SAE 75W-85W Or 75W-90 
\b
\
 \
\
\
 \
\
\



Automatic  All  "ATF DEXRON II" Or 

Transmission   Equivalent 
\b
\
 \
\
\
 \
\
\



Brake Fluid  All  DOT 3 Or DOT 4 
\b
\
 \
\
\
 \
\
\



Rear Axle  All API Classification GL-5

  Or Higher (
2) 
\b
\
\
\
\
\
\
\





(
1) - SAE 5W-30 engine oil is preferred. SAE 10W-30 may be used if 

the Ambient Temperature is above 0 F (-18 C). 

(
2) - SAE90, 85W-90, 80W-90 may be used in temperatures above 

-10 F (-23 C). SAE 80W, 80W-90 may be used in temperatures 

from -30 F (-34 C) to -10 F (-23 C). SAE 75W may be used 

in temperatures below -30 F (-34 C). 
\f
\
\
\
\
\
\
\


FLUID CAPACITIES
FLUID CAPACITIES TABLE ( 1)
\
\
\
\
\
\
\
 
Item  Condition  Specification 
\b
\
 \
\
\
 \
\
\



Engine Oil  Oil Pan  4.5 Qts. (4.3L) 

(
1) \b \
\
\
 \
\



 Oil Filter  0.32 Qts. (0.3L) 

\b
\
\
\
 \
\



 Oil Cooler  0.32 Qts. (0.3L) 
\b
\
 \
\
\
 \
\
\



Power  Drained  1.1 Qts. (1.0L) 

Steering   
\b
\
 \
\
\
 \
\
\



Automatic  Drained  8.9 Qts. (8.5L) 

Transmission   
\b
\
 \
\
\
 \
\
\



Manual  Drained  3.3 Qts. (3.2L) 

Transmission   
\b
\
 \
\
\
 \
\
\



Transfer Case Drained  2.6 Qts. (2.5L) 
\b
\
 \
\
\
 \
\
\



Front Axle  Drained  1.3 Qts. (1.2L) 
\b
\
 \
\
\
 \
\
\



Rear Axle  Drained  3.3 Qts. (3.2L) 
\b
\
 \
\
\
 \
\
\



A/C  Drained  27 oz (760 g) 

Refrigerant   
\b
\
 \
\
\
 \
\
\



Fuel Tank  Capacity  24 gal (92L) 

Lubricant level should be to bottom of fill hole on side of
transfer case.
RECOMMENDED FLUID
Transaxle/Transmission
Except Montero, use Diamond ATF SP-II. On Montero, use
Dexron-II ATF.
Transfer Cases
Use SAE 75W-85 gear oil with API GL-4 rating or higher.
FLUID CAPACITIES
TRANSAXLE/TRANSMISSION REFILL CAPACITIES








\









\









\









\









\









\









\







Application Qts. (L)\
Diamante ................................................. 9.0 (8.5)\
Eclipse
2.0L Non-Turbo ......................................... 9.1 (8.6)\
2.0L Turbo ............................................. 7.1 (6.7)\
2.4L ................................................... 6.4 (6.1)\
Galant ................................................... 6.3 (6.0)\
Mirage ................................................... 8.2 (7.8)\
Montero ................................................. 10.4 (9.8)\
3000GT ................................................... 7.9 (7.5)\









\









\









\









\









\









\









\







TRANSFER CASE REFILL CAPACITIES








\









\









\









\









\









\









\







Application Pts. (L)\
Eclipse AWD ............................................... 1.0 (.5)\
Montero .................................................. 5.3 (2.5)\
Montero Sport ............................................ 4.9 (2.3)\
3000GT ..................................................... .6 (.3)\









\









\









\









\









\









\









\







DRAINING & REFILLING
NOTE: Although manufacturer recommends changing only fluid, the
oil filter/screen may also require replacement. If replacing
oil filter/screen, note length and location of all bolts.
Transaxle (Except Montero)
1) Remove drain plug(s), and drain fluid. Some models may
contain a drain plug located in housing below axle shaft, in oil pan.
Remove oil pan. Remove oil filter/screen if necessary.
2) If oil filter/screen is replaced, tighten bolts to
specification. See TORQUE SPECIFICATIONS . Clean oil pan, replace
gasket, and install oil pan. Tighten oil pan bolts and drain plug to
specification. See TORQUE SPECIFICATIONS . Ensure dipstick hole area is
clean. Fill transmission with Diamond ATF SP-II, through filler tube,
until COLD level is reached on dipstick.
3) Start engine and allow to idle for 2 minutes. Shift
transaxle to each position, ending in Neutral. Add sufficient fluid to
reach lower mark. After reaching normal operating temperature, fluid
should be between upper and lower marks of HOT range on dipstick.
Transmission (Montero)
1) Remove drain plug (if equipped) from transmission pan, an\
d
allow fluid to drain. On models without drain plug, oil pan must be

TRANSMISSION SERVICING - M/T
1998 Mitsubishi Montero
1997-98 TRANSMISSION SERVICING
Mitsubishi Manual Transmission
Eclipse, Galant, Mirage, Montero, 3000GT
IDENTIFICATION
MANUAL TRANSMISSION APPLICATIONS








\









\









\









\









\









\









\







Model Transmission/Transaxle (Model)\
Eclipse
AWD .................................... 5-Speed Transaxle (W5M33)\
FWD
2.0L Non-Turbo ....................... 5-Speed Transaxle (F5MC1)\
2.0L Turbo ........................... 5-Speed Transaxle (F5M33)\
2.4L ................................. 5-Speed Transaxle (F5M31)\
Galant ................................... 5-Speed Transaxle (F5M31)\
Mirage
1.5L ................................... 5-Speed Transaxle (F5M41)\
1.8L ................................... 5-Speed Transaxle (F5M42)\
Montero
2WD ................................. 5-Speed Transmission (R5M21)\
4WD ................................. 5-Speed Transmission (V5MT1)\
3000GT
SOHC & DOHC Non-Turbo .................. 5-Speed Transaxle (F5M33)\
DOHC Turbo ............................. 6-Speed Transaxle (W6MG1)\









\









\









\









\









\









\









\







LUBRICATION
SERVICE INTERVALS
Check transaxle/transmission and transfer case fluid level
every 30,000 miles. Change fluid at 30,000 miles if operated under
severe conditions.
CHECKING FLUID LEVEL
Transaxle/Transmission
Check fluid level at fill hole on side of transaxle or
transmission. Lubricant must be at bottom of fill hole.
Transfer Case
Transfer case contains separate drain and fill plugs.
Lubricant must be at bottom of fill hole.
RECOMMENDED FLUID
Transaxle/Transmission
Use API classification GL-4 or higher SAE 75W-85W gear oil.
Transfer Case
Use API classification GL-4 or higher SAE 75W-85W gear oil.
FLUID CAPACITIES
TRANSAXLE/TRANSMISSION REFILL CAPACITIES