1998 MITSUBISHI MONTERO height

Removal & Installation
1) Drain master cylinder. Remove cotter pin, washer and
clevis pin. Disconnect push rod from clutch pedal. Remove and plug
hydraulic line at clutch master cylinder.
2) Remove retaining nuts, clutch master cylinder and gasket.
To install, reverse removal procedure. Apply grease to clevis pin
before installing. Fill reservoir and bleed clutch system. See
BLEEDING CLUTCH HYDRAULIC SYSTEM .
CLUTCH RELEASE CYLINDER
Removal & Installation
Remove and plug hydraulic line at release cylinder. Remove
cylinder-to-transmission bolts. Remove clutch release cylinder. To
install, reverse removal procedure. Apply grease to push rod-to-
release fork contact area. Bleed clutch system. See
BLEEDING CLUTCH HYDRAULIC SYSTEM .
BLEEDING CLUTCH HYDRAULIC SYSTEM
Attach hose to bleeder fitting located on clutch release
cylinder, next to hydraulic line. Submerge other end of hose in
container half full of clean brake fluid. Fill reservoir with brake
fluid. Open bleeder fitting. Have assistant press clutch pedal to full
release position. Close bleeder fitting. Release clutch pedal. Repeat
until air bubbles no longer emerge from hose. Refill reservoir.
OVERHAUL
CLUTCH MASTER CYLINDER
NOTE: DO NOT disassemble piston assembly.
Disassembly
Remove piston stop ring, damper and push rod assembly. See
Fig. 6 . Remove piston assembly. Note position of reservoir band for
reassembly reference. Remove reservoir.
Inspection & Reassembly
Inspect components for corrosion, scoring or damage. Replace
if necessary. Apply brake fluid to components during reassembly. On
Montero, adjust clutch master cylinder push rod to 5.90" (150 mm). On
Montero Sport, push rod adjustment is correct after adjusting clutch
pedal free play and pedal height. See CLUTCH PEDAL FREE PLAY and
CLUTCH PEDAL HEIGHT under ADJUSTMENTS. To reassemble, reverse
disassembly procedure. Ensure piston moves freely in bore.
Fig. 6: Exploded View Of Clutch Master Cylinder (Typical)
Courtesy of Mitsubishi Motor Sales of America.

races are fully seated. Install Pinion Height Gauge (MB990901-01) with\
pinion bearings. See Fig. 6. DO NOT install oil seal.
2) Using INCH-lb. torque wrench, measure pinion rotating
torque. Gradually tighten pinion height gauge to increase rotating
torque to proper specification. See
PINION ROTATING TORQUE SPECIFICATIONS table. Install Cylinder Gauge
(MB990903-01). Ensure flat areas are aligned and that gauge contacts
carrier bearing bores firmly. See Fig. 6.
3) Select adjusting shim with same thickness as gap between
cylinder gauge and pinion height gauge. Use minimum amount of
adjusting shims. Install selected adjusting shims between drive pinion
gear and rear drive pinion bearing. Using Bearing Installer (MB990802-
01), install rear pinion bearing.
PINION ROTATING TORQUE SPECIFICATIONS









\









\









\









\









\









\









\







Application INCH Lbs. (N.m)\
Oil Seal Not Installed
With Lubrication ............................... 1.3-2.2 (.15-.25)\
Without Lubrication ............................ 2.6-4.3 (.30-.50)\
Oil Seal Installed
With Lubrication ............................... 3.1-3.9 (.35-.45)\
Without Lubrication ............................ 4.3-6.1 (.50-.70)\









\









\









\









\









\









\









\







Fig. 6: Setting Drive Pinion Depth
Courtesy of Mitsubishi Motor Sales of America.
Drive Pinion Preload
1) Install drive pinion in differential carrier. Install

Fig. 17: Checking Differential Starting Torque
Courtesy of Mitsubishi Motor Sales of America.
13) Ensure starting torque is within specification. See
STARTING TORQUE table. Ensure adhesive is removed from ring gear
mounting bolts and gear mounting surface. Clean internal threads with
tap.
14) Ensure alignment marks on differential case and ring gear
align. Apply Loctite 271 to bolts, and install ring gear on
differential case. Tighten bolts in diagonal sequence to
specification. See TORQUE SPECIFICATIONS .
STARTING TORQUE









\









\









\









\









\









\









\







Application Ft. Lbs. (N.m)\
Used Clutch Plates ................................... 29-54 (40-75)\
New Clutch Plates .................................... 18-54 (25-75)\









\









\









\









\









\









\









\







Carrier Assembly & Drive Pinion Installation
1) Install pinion bearing races in differential housing.
Ensure races are fully seated. Install Pinion Height Gauge (MB990901)
and pinion bearings. See Fig. 18. DO NOT install oil seal.

Fig. 18: Setting Pinion Height
Courtesy of Mitsubishi Motor Sales of America.
2) Using torque wrench, measure pinion rotating torque.
Gradually tighten pinion height gauge to increase rotating torque. See

PINION ROTATING TORQUE SPECIFICATIONS table.
PINION ROTATING TORQUE SPECIFICATIONS









\









\









\









\









\









\









\







Application INCH Lbs. (N.m)\
Oil Seal Not Installed
With Lubrication ................................. 3.5-4.3 (.4-.5)\
Without Lubrication .............................. 5.2-7.8 (.6-.9)\
Oil Seal Installed
With Lubrication ............................... 5.6-6.5 (.65-.75)\
Without Lubrication .......................... 7.4-10.0 (.85-1.15)\









\









\









\









\









\









\









\







3) Install cylinder gauge in side bearing seats. Ensure flat
areas align, and gauge contacts side bearing seat firmly. Select
adjusting shim with same thickness as gap between cylinder gauge and
pinion height gauge.
4) Use minimum amount of adjusting shims. Install selected
adjusting shims between drive pinion gear and rear pinion bearing.
Using bearing installer and press, install rear pinion bearing.
5) Install drive pinion in differential housing. Install
spacer, pinion front shim(s) and front pinion bearing. DO NOT install
oil seal. Install pinion companion flange, washer and retaining nut.
Tighten nut to specification. See TORQUE SPECIFICATIONS.
6) Check pinion rotating torque. See
PINION ROTATING TORQUE SPECIFICATIONS table. Adjust rotating torque by
replacing drive pinion front shims or spacer. Once correct rotating
torque is obtained, install oil seal. Coat seal lip with grease.
Install pinion companion flange so alignment marks are correct. Apply
light coat of grease to contact area of pinion flange washer.
7) Install NEW retaining nut. Recheck pinion rotating torque.
Ensure rotating torque is within specification. Press side bearings
onto differential case. Install outer races. Install differential
carrier into differential housing. Align bearing cap index marks, and
snug carrier cap bolts. Ensure outer races and bearing caps are
installed in original location.
8) Install side bearing nuts. Tighten bearing cap bolts to
specification. See TORQUE SPECIFICATIONS . Tighten bearing nuts until
bearing outer races are seated against bearings. Adjust ring gear
backlash.
Ring Gear Backlash
1) Secure drive pinion in place. Using dial indicator, check
ring gear backlash at heel of ring gear tooth. See Fig. 6. Measure at
4 locations of ring gear. Gear backlash must be within specification.
Backlash should be .005-.007" (.13-.18 mm).
2) If backlash is less than specification, loosen side
bearing nut at back of ring gear, and tighten side bearing nut on
tooth side of ring gear by same amount. If backlash exceeds
specification, loosen side bearing nut at tooth side of ring gear, and
tighten side bearing nut at back of ring gear by same amount.
3) After adjusting backlash, tighten both side bearing nuts
half the distance between 2 adjacent holes on side bearing nut.
Recheck backlash. Ensure bearing cap bolts are tightened to
specification. See TORQUE SPECIFICATIONS .
4) Lock plates are of 2 designs for hole location of side
bearing nuts. Install proper type lock plate. Tighten lock plate bolt
to specification. See TORQUE SPECIFICATIONS. Check gear tooth contact
pattern. See GEAR TOOTH CONTACT PATTERNS article in GENERAL
INFORMATION.
Ring Gear Runout

spring tester, test valve spring pressure at installed and compressed
heights. See Fig. 5.
Usually compressed height is installed height minus valve
lift. Replace valve spring if not within specification. It is
recommended to replace all valve springs when overhauling cylinder
head.
Fig. 5: Checking Valve Spring Pressure - Typical
This Graphic For General Information Only
VALVE GUIDE
Measuring Valve Guide Clearance
Check valve stem-to-guide clearance. Ensure valve stem
diameter is within specifications. Install valve in valve guide.
Install dial indicator assembly on cylinder head with tip resting
against valve stem just above valve guide. See Fig. 6.

the old insert and machining an oversize insert bore. Replacement
oversize insert is usually chilled and the cylinder head is sometimes
warmed. Valve seat is pressed into the head. This operation requires
specialized machine shop equipment.
Valve Seat Concentricity
Using dial gauge, install gauge pilot in valve guide.
Position gauge arm on the valve seat. Adjust dial indicator to zero.
Rotate arm 360 degrees and note reading. Runout should not exceed
specification.
To check valve-to-valve seat concentricity, coat valve face
lightly with Prussian Blue dye. Install valve and rotate it on valve
seat. If pattern is even and entire seat is coated at valve contact
point, valve is concentric with the seat.
REASSEMBLY
Valve Stem Installed Height
Valve stem installed height must be checked when new valves
are installed or when valves or valve seats have been ground. Install
valve in valve guide. Measure distance from tip of valve stem to
spring seat. See Fig. 11. Distance must be within specifications.
Fig. 11: Measuring Valve Stem Installed Height - Typical
This Graphic For General Information Only
Remove valve and grind valve stem tip if height exceeds
specification. Valve tips are surface hardened. DO NOT remove more

than .010" (.25 mm) from tip. Chamfer sharp edge of reground valve
tip. Recheck valve stem installed height.
VALVE STEM OIL SEALS
Valve stem oil seals must be installed on valve stem. See
Fig. 2 . Seals are needed due to pressure differential at the ends of
valve guides. Atmospheric pressure above intake guide, combined with
manifold vacuum below guide, causes oil to be drawn into the cylinder.
Exhaust guides also have pressure differential created by
exhaust gas flowing past the guide, creating a low pressure area. This
low pressure area draws oil into the exhaust system.
Replacement (On Vehicle)
Mark rocker arm or overhead cam components for location.
Remove rocker arm components or overhead cam components. Components
must be installed in original location. Remove spark plugs. Valve stem
oil seals may be replaced by holding valves against seats using air
pressure.
Air pressure must be installed in cylinder using an adapter
for spark plug hole. An adapter can be constructed by welding air hose
connection to spark plug body with porcelain removed.
Install adapter in spark plug hole. Apply a minimum of 140
psi (9.8 kg/cm
) to adapter. Air pressure should hold valve closed. If
air pressure does not hold valve closed, check for damaged or bent
valve. Cylinder head must be removed for service.
Using valve spring compressor, compress valve springs. Remove
valve locks. Carefully release spring compressor. Remove retainer or
rotator and valve spring. Remove valve stem oil seal.
If oversized valves have been installed, oversized oil seals
must be used. Coat valve stem with engine oil. Install protective
sleeve over end of valve stem. Install new oil seal over valve stem
and seat on valve guide. Remove protective sleeve. Install spring
seat, valve spring and retainer or rotator. Compress spring and
install valve locks. Remove spring compressor. Ensure valve locks
are fully seated.
Install rocker arms or overhead cam components. Tighten all
bolts to specification. Adjust valves if required. Remove adapter.
Install spark plugs, valve cover and gasket.
VALVE SPRING INSTALLED HEIGHT
Valve spring installed height should be checked during
reassembly. Measure height from lower edge of valve spring to the
upper edge. DO NOT include valve spring seat or retainer. Distance
must be within specifications. If valves and/or seats have been
ground, a valve spring shim may be required to correct spring height.
See Fig. 12 .
Fig. 12: Measuring Valve Spring Installed Height - Typical
This Graphic For General Information Only