1998 MITSUBISHI MONTERO seat adjustment
[x] Cancel search: seat adjustmentPage 1355 of 1501
and remove. Disconnect all external solenoid and switch connections.
3) On Montero 4WD, remove catalytic converter and front
exhaust pipe. On all models, disconnect speedometer cable and control
cables at transmission. Remove starter and bellhousing cover. Place
reference mark on torque converter and drive plate for reassembly
reference. Remove torque converter bolts. Push torque converter back
and away from drive plate.
4) Disconnect transmission cooler lines. Remove oil filler
tube. Secure transmission on a jack. Raise transmission slightly to
take weight off mount. Remove crossmember-to-mount bolts and
crossmember.
5) Remove transfer case mounting bracket and mount (if
equipped). Remove transmission-to-engine mounting bolts. Carefully
lower transmission from vehicle.
CAUTION: Ensure torque converter is fully seated in transmission
before installation.
Installation
1) To install, reverse removal procedure. Tighten
transmission-to-engine bolts and torque converter-to-drive plate bolts
to specification. See TORQUE SPECIFICATIONS. Tighten mount bolts with
weight of engine and transmission on mounts. Ensure reference marks on
drive shaft(s) and torque converter-to-drive plate are matched.
2) Apply sealant to transfer case gearshift assembly gasket
before installation. Coat transmission oil filler tube "O" ring with
transmission fluid before installation. Refill transmission fluid to
specified level. See LUBRICATION in TRANSMISSION SERVICING - A/T
article. Adjust all control cables. See ADJUSTMENTS in
TRANSMISSION SERVICING - A/T article.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS - FWD MODELS \
\
\
\
\
\
\
Applications Ft. Lbs. (N.m)\
Ball Joint Nut ............................................ 74 (100)\
Center Crossmember Assembly Front Bolt ..................... 69 (93)\
Center Crossmember Assembly Rear Bolt ...................... 52 (70)\
Starter Bolts .............................................. 22 (30)\
Tie Rod End Nut ............................................ 21 (28)\
Torque Converter-To-Drive Plate Bolt ................. 33-38 (45-52)\
Transaxle-To-Engine Block Bolt
8-mm Bolt .................................................... ( 1)
10-mm Bolt ......................................... 22-25 (30-34)\
12-mm Bolt ......................................... 31-40 (42-54)\
Upper Coupling Bolts
2.4L ..................................................... 35 (48)\
3.0L ..................................................... 54 (73)\
Lower Coupling Bolts
2.4L ..................................................... 35 (48)\
3.0L ..................................................... 65 (88)\
( 1) - Tighten to 84-108 INCH lbs. (10-12 N.m).
\
\
\
\
\
\
\
TORQUE SPECIFICATIONS - RWD MODELS \
\
\
\
\
\
\
Applications Ft. Lbs. (N.m)\
Engine-To-Transmission Bolt ................................ 65 (88)\
Page 1402 of 1501
Worn or dirty needle valve Clean carburetor, see
and seat ENGINE PERFORMANCE
Float sticking Readjust or replace
float see the ENGINE
PERFORMANCE section
Incorrect choke adjustment Reset choke adjustment
see ENGINE PERFORMANCE
Defective coil Replace coil
Improper spark plug gap Regap spark plugs
Incorrect ignition timing Reset ignition timing
see ENGINE PERFORMANCE
\
\
\
\
\
\
\
Detonation Over-advanced ignition Reset ignition timing
timing see ENGINE PERFORMANCE
Defective spark plugs Replace spark plugs
Fuel lines clogged Clean fuel lines
EGR system malfunction Check and repair EGR
system
PCV system malfunction Repair PCV system
Vacuum leaks Check and repair
vacuum system
Loose fan belts Tighten or replace
fan belts, see ENGINE
PERFORMANCE
Restricted airflow Remove restriction
Vacuum advance malfunction Check distributor
operation
\
\
\
\
\
\
\
Dieseling Binding carburetor linkage Eliminate binding
Binding throttle linkage Eliminate blinding
Binding choke linkage or Eliminate binding
fast idle cam
Defective idle solenoid Replace idle solenoid
see ENGINE PERFORMANCE
Improper base idle speed Reset idle speed, see
see ENGINE PERFORMANCE
Incorrect ignition timing Reset ignition timing
see ENGINE PERFORMANCE
Incorrect idle mixture Reset idle mixture,
setting see ENGINE PERFORMANCE
\
\
\
\
\
\
\
Faulty Incorrect ignition timing Reset ignition timing
Acceleration see ENGINE PERFORMANCE
Page 1406 of 1501
setting, see ENGINE
PERFORMANCE
Vacuum leak Eliminate vacuum leak
EGR valve malfunction Replace EGR valve
\
\
\
\
\
\
\
Poor Gasoline Cracked or broken vacuum Replace vacuum hoses
Mileage hoses
Vacuum leaks Repair vacuum leaks
Defective ignition wires Replace wires
Incorrect choke setting Readjust setting, see
ENGINE PERFORMANCE
Defective vacuum advance Replace vacuum advance
Defective spark plugs Replace spark plugs
Binding carburetor power Eliminate binding
piston
Dirt in carburetor jets Clean and/or replace
jets
Incorrect float adjustment Readjust float
setting, see FUEL
Defective power valve Replace power valve,
see ENGINE PERFORMANCE
Incorrect idle speed Readjust idle speed
\
\
\
\
\
\
\
Engine Stalls Improper float level Readjust float level
Leaking needle valve and Replace needle valve
seat and seat
Vacuum leaks Eliminate vacuum
leaks
\
\
\
\
\
\
\
VACUUM PUMP - DIESEL TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
NOTE: Diesel engines mechanical diagnosis is the same as gasoline
engines for items such as noisy valves, bearings, pistons,
etc. The following trouble shooting covers only items
pertaining to diesel engines.
VACUUM PUMP (DIESEL) TROUBLE SHOOTING CHART
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Page 1423 of 1501
Column not correctly See STEERING COLUMNS
aligned article
Broken lower joint Replace joint
Horn contact ring not See STEERING COLUMN
article
Bearing not lubricated See STEERING COLUMN
article
Shaft snap ring not Reseat or replace snap
properly seated ring
Plastic spherical joint See STEERING COLUMN
not lubricated article
Shroud or housing loose Tighten holding screws
Lock plate retaining See STEERING COLUMN
ring not seated article
Loose sight shield Tighten holding screws
\
\
\
\
\
\
\
High Steering Column assembly See STEERING COLUMN
Shaft Effort misaligned article
Improperly installed dust Adjust or replace
shield
Tight steering universal See STEERING COLUMN
joint article
\
\
\
\
\
\
\
High Shift Column is out of See STEERING COLUMN
Effort alignment article
Improperly installed Adjust or replace
dust shield
Seals or bearings not See STEERING COLUMNS
lubricated article
Mounting bracket screws Replace with new
too long shorter screws
Burrs on shift tube Remove burrs or replace
tube
Lower bowl bearing See STEERING COLUMN
assembled wrong article
Shift tube bent or broken Replace as necessary
Improper adjustment of See STEERING COLUMN
shift levers article
\
\
\
\
\
\
\
Improper Trans. Sheared shift tube joint Replace as necessary
Shifting
Sheared lower shaft lever Replace as necessary
Improper shift lever See STEERING COLUMN
adjustment article
Page 1428 of 1501
Wheel alignment out of See Adjustment in
tolerance WHEEL ALIGNMENT section
Broken spring See SUSPENSION section
Defective shock absorbers Replace shock absorbers
Worn steering & suspension See SUSPENSION section
components
\
\
\
\
\
\
\
Front End Shimmy Tire out of balance/round Check tire balance
Excessive wheel runout See WHEEL ALIGNMENT
Insufficient or improper See WHEEL ALIGNMENT
caster section
Worn suspension or steering See SUSPENSION section
components
Defective shock absorbers Replace shock absorber
Wheel bearings worn or See WHEEL BEARING ADJ.
loose in SUSPENSION section
Power steering reaction See STEERING section
Bracket loose
Steering gear box (rack) See STEERING section
mounting loose
Steering gear adjustment See STEERING section
loose
Worn spherical joints See SUSPENSION section
\
\
\
\
\
\
\
Toe-In Not Lower control arm bent See SUSPENSION section
Adjustable
Frame bent Check frame for damage
\
\
\
\
\
\
\
Camber Not Control arm bent See SUSPENSION section
Adjustable
Frame bent Check frame for damage
Hub & bearing not seated See SUSPENSION section
properly
\
\
\
\
\
\
\