1998 Lexus LS400 battery

IN CASE OF AN EMERGENCY
194
(b) Starting a flooded engine
If the engine will not start, your engine may be flooded because
of repeated cranking.
If this happens, turn the key to ”START” with the accelerator pedal
held down. Continue this operation for 30 seconds and then stop
cranking. Then try starting the engine with your foot off the
accelerator pedal.
If the engine does not start after 30 seconds of cranking, release the
key, wait a few minutes and try again.
If the engine still will not start, it needs adjustment or repair. Call a
Lexus dealer. Roadside Assistance or Customer Service Assistance.
(See ”Foreword”.)
NOTICE
Do not crank for more than 30 seconds at a time. This may
overheat the starter and wiring systems.
(c) Jump starting
To avoid serious personal injury and damage to your vehicle
which might result from battery explosion, acid burns, electrical
burns, or damaged electronic components, these instructions
must be followed precisely.
If you are unsure about how to follow this procedure, we strongly
recommend that you seek help from your Lexus dealer, Roadside
Assistance or Customer Service Assistance. (See ”Foreword”.).
CAUTION
Batteries contain sulfuric acid which is poisonous and
corrosive. Wear protective safety glasses when jump
starting, and avoid spilling acid on your skin, clothing, or
vehicle.
If you should accidentally get acid on yourself or in your
eyes, remove any contaminated clothing and flush the
affected area with water immediately. Then get immediate
medical attention. If possible, continue to apply water with
a sponge or cloth while en route to the medical office.
The gas normally produced by a battery will explode if a
flame or spark is brought near. Use only standardized
jumper cables and do not smoke or light a match while
jump starting.
NOTICE
The battery used for boosting must be 12 V. Do not jump start
unless you are sure that the booster battery is correct.

IN CASE OF AN EMERGENCY
195
40L002-7
5
Discharged battery 6
Booster battery
JUMP STARTING PROCEDURE
1. If the booster battery is installed in another vehicle, make sure the
vehicles are not touching. Turn off all unnecessary lights and
accessories.2. If required, remove all the vent plugs from the booster battery.
Lay a cloth over the open vents on the booster battery. (This helps
reduce the explosion hazard, personal injuries and burns.)
If the booster battery is an extended maintenance interval battery, it
is not necessary to remove the vent plugs.
3. If the engine in the vehicle with the booster battery is not running,
start it and let it run for about 5 minutes. During jump starting, run
the engine at about 2000 rpm with the accelerator pedal lightly
depressed.
4. Locate positive (+) and negative () terminals of each battery.
Connect the jumper cables in the exact order (
1
2
3
4
)
shown in the illustration.
1
Connect a positive (red) jumper cable clamp to the positive (+)
terminal of the discharged battery.
2
Connect the clamp at the other end of the positive (red) cable
to the positive (+) terminal of the booster battery.
3
Connect a negative (black) cable clamp to the negative ()
terminal of the booster battery.
4
Connect the clamp at the other end of the negative (black) cable
to a solid, stationary, unpainted metallic point (e.g. engine
hanger) away from the battery. Do not connect it to or near any
part that moves when the engine is cranked.

IN CASE OF AN EMERGENCY
196
CAUTION
When making the connections, to avoid serious injury, do not
lean over the battery or accidentally let the jumper cables or
clamps touch anything except the correct battery terminals or
the ground.
5. Start your engine in the normal way. After starting, run it at about
2000 rpm for several minutes with the accelerator pedal lightly
depressed.
6. Carefully disconnect the cables in the exact reverse order: the
negative cable and then the positive cable.
7. Carefully dispose of the battery cover cloths which may now
contain sulfuric acid.
8. If removed, replace all the battery vent plugs.
If the cause of your battery discharging is not apparent (for example,
lights left on), you should have it checked.
IF YOUR VEHICLE OVERHEATS
If your engine coolant temperature gauge indicates overheating,
if you experience a loss of power, or if you hear a loud knocking
or pinging noise, the engine has probably overheated.
When the engine overheats
Pull safely off the road, stop the vehicle and turn on your emergency
flashers. Put the transmission in ”P” and apply the parking brake.
A: If steam is coming from your engine:
Turn off the engine. Leave the hood closed until there is no sign of
steam or coolant. Your engine could have been seriously damaged
already. Call your Lexus dealer for assistance.
CAUTION
To help avoid personal injury, keep the hood closed until there
is no steam. Escaping steam or coolant is sign of very high
pressure.

MAINTENANCE
216Parking brake
Check that the pedal has the proper travel and that, on a safe incline,
your vehicle is held securely with only the parking brake applied.
Automatic transmission ”Park” mechanism
On a safe incline, check that your vehicle is held securely with the
selector lever in ”P” position and all brakes released.
Engine compartment
Items listed below should be checked from time to time, e.g. each
time when refueling.
Washer fluid
Make sure there is sufficient fluid in the tank. See page 261 for
additional information.
Engine coolant level
Make sure the coolant level is between the Upper and Lower lines
on the seethrough reservoir when the engine is cold. See page 233
for additional information.
Battery
Your Lexus has a maintenance free battery. You do not have to add
distilled water. For longer life of the battery, however, see page 253
for additional information.
Brake fluid level
Make sure the brake fluid level is correct. See page 239 for
additional information.Engine oil level
Check the level on the dipstick with the engine turned off and the
vehicle parked on a level spot. See page 230 for additional
information.
Power steering fluid level
Check the level on the dipstick. The level should be in the ”HOT”
or ”COLD” range depending on the fluid temperature. See page 240
for additional information.
Exhaust system
Look for cracks, holes and loose supports. If you notice any change
in the sound of the exhaust or smell exhaust fumes, have the cause
located and corrected immediately. (See engine exhaust cautions in
Section 31.)

61L005-5
INTRODUCTION
220
ENGINE COMPARTMENT OVERVIEW
1 Brake fluid reservoir
2 Fuse box
3 Battery
4 Washer fluid tank
5 Engine oil level dipstick
6 Engine oil filler cap
7 Power steering fluid
reservoir
8 Engine coolant reservoir

INTRODUCTION
221
DOITYOURSELF SERVICE
PRECAUTIONS
If you perform maintenance yourself, be sure to follow the
correct procedure given in this Section.
You should be aware that improper or incomplete servicing may
result in operating problems.
Performing doityourself maintenance during the warranty period
may affect your warranty coverage. Read the separate Lexus
Warranty statement for details and suggestions.
This Section gives instructions only for those items that are
relatively easy for an owner to perform. As explained in Section 5,
there are still a number of items that must be performed by a qualified
technician with special tools.
For information on tools and parts for doityourself maintenance,
see ”Parts and tools”.
Utmost care should be taken when working on your vehicle to
prevent accidental injury. Here are a few precautions that you should
be especially careful to observe:
CAUTION
When the engine is running, keep hands, clothing, and tools
away from the moving fan and engine drive belt.
(Removing rings, watches, and ties is advisable.)
Right after driving, the engine compartment the engine,
radiator, exhaust manifold and power steering fluid
reservoir, etc. will be hot. So be careful not to touch them.
Oil and other fluids may also be hot.
Do not smoke, cause sparks or allow open flames around
fuel or the battery. Their fumes are flammable.
Be extremely cautious when working on the battery. It
contains poisonous and corrosive sulfuric acid.
Do not get under your vehicle with just the body jack
supporting it. Always use automotive jack stands or other
solid supports.
Be sure the ignition is off if you work near the electric
cooling fan or radiator grille. With the ignition on, the
electric cooling fan may automatically start to run if the air
conditioning is on and/or if the coolant temperature is high.
Use eye protection whenever you work on or under your
vehicle where you may be exposed to flying or falling
material, fluid spray, etc.
NOTICE

INTRODUCTION
222Remember that battery and ignition cables carry high
currents or voltages. Be careful of accidentally causing a
short circuit.
Before closing the engine hood, check to see that you have not
forgotten any tools, rags, etc.
Do not drive with the air cleaner removed, or excessive engine
wear could result. Also backfiring could cause a fire in the
engine compartment.
Do not overfill automatic transmission fluid, or the
transmission could be damaged.
Be careful not to scratch the glass surface with the wiper
frame.
PARTS AND TOOLS
Here is a list of parts and tools you will need to perform
doityourself maintenance. Remember all Lexus parts are
designed in metric sizes, so your tools must be metric.
Checking the engine oil level
Parts (if level is low):
Use API grade SH, ”EnergyConserving II” or SJ,
”EnergyConserving” multigrade engine oil or ILSAC
multigrade engine oil. For recommended oil viscosity, see page
232.
Tools:
Rag or paper towel
Funnel (only for adding oil)
Checking the engine coolant level
Parts (if level is low):
Ethyleneglycol coolant
Demineralized or distilled water
Tools:
Funnel (only for adding coolant)

INTRODUCTION
223
Checking brake fluid
Parts (if level is low):
FMVSS No. 116 DOT 3 or SAE J1703 brake fluid
Tools:
Funnel (only for adding fluid)
Checking power steering fluid
Parts (if level is low):
Automatic transmission fluid DEXRON
II or III
Tools:
Rag or paper towel
Funnel (only for adding fluid)
Checking battery condition
Nonmaintenance batteries
Tools:
Warm water
Baking soda
Grease
Conventional wrench (for terminal clamp bolts)
Maintenance type batteries
Parts (if level is low):
Distilled waterTools:
Warm water
Baking soda
Grease
Conventional wrench (for terminal clamp bolts)
Coin (for vent plugs)
Funnel (only for adding distilled water)
Checking and replacing the blade type fuses
Parts (if replacement is necessary):
Fuse with same amperage rating as original
Checking the cartridge type fuses
Parts (if replacement is necessary):
Genuine Lexus fuse or equivalent with same amperage rating as
original
Adding washer fluid
Parts:
Water
Washer fluid containing antifreeze (for winter use)
Tools:
Funnel