1998 Lexus LS400 engine oil

INTRODUCTION
222Remember that battery and ignition cables carry high
currents or voltages. Be careful of accidentally causing a
short circuit.
Before closing the engine hood, check to see that you have not
forgotten any tools, rags, etc.
Do not drive with the air cleaner removed, or excessive engine
wear could result. Also backfiring could cause a fire in the
engine compartment.
Do not overfill automatic transmission fluid, or the
transmission could be damaged.
Be careful not to scratch the glass surface with the wiper
frame.
PARTS AND TOOLS
Here is a list of parts and tools you will need to perform
doityourself maintenance. Remember all Lexus parts are
designed in metric sizes, so your tools must be metric.
Checking the engine oil level
Parts (if level is low):
Use API grade SH, ”EnergyConserving II” or SJ,
”EnergyConserving” multigrade engine oil or ILSAC
multigrade engine oil. For recommended oil viscosity, see page
232.
Tools:
Rag or paper towel
Funnel (only for adding oil)
Checking the engine coolant level
Parts (if level is low):
Ethyleneglycol coolant
Demineralized or distilled water
Tools:
Funnel (only for adding coolant)

SECTION 6 2
224
SERVICE PROCEDURES AND
SPECIFICATIONS
Engine
Specifications 225. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel 227. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Facts about engine oil consumption 229. . . . . . . . . . . . . . . . . . . . . . . . . . .
Used engine oil 230. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking the engine oil level 230. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking the engine coolant level 233. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spark plugs 234. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

62L0051
Temperature range anticipated before next oil change
ENGINE
225
SPECIFICATIONS
GENERAL
Model
Type
Bore and stroke
Displacement
Valve clearance (engine cold)
Intake
Exhaust
Drive belt tension
1UZFE
8 cylinder V type, 4 cycle, gasoline
87.5 X 82.5 mm (3.44 X 3.25 in.)
3969 cm
3 (242.1 cu.in.)
0.15 0.25 mm (0.006 0.010 in.)
0.25 0.35 mm (0.010 0.014 in.)
Automatic adjustment
LUBRICATION SYSTEM
Oil capacity
Drain and refill
with filter
without filter
Oil grade

Recommended oil viscosity (SAE):
5.6 L (5.9 qt., 4.9 lmp.qt.)
5.3 L (5.6 qt., 4.7 lmp.qt.)
API SH, ”EnergyConserving II” or SJ, ”EnergyConserving”
multigrade engine oil or ILSAC multigrade engine oil

ENGINE
229
FACTS ABOUT ENGINE OIL
CONSUMPTION
Functions of engine oil
Engine oil has the primary function of lubricating and cooling the
inside of the engine, and plays a major role in maintaining the engine
in proper working order.
Engine oil consumption
It is normal that an engine should consume some engine oil
during normal engine operation. The causes of oil consumption
in a normal engine are as follows.
Oil is used to lubricate pistons, piston rings and cylinders. A thin
film of oil is left on the cylinder wall when a piston moves
downwards in the cylinder. High negative pressure generated
when the vehicle is decelerating sucks some of this oil into the
combustion chamber. This oil as well as some part of the oil film
left on the cylinder wall is burned by the high temperature
combustion gases during the combustion process.
Oil is also used to lubricate the stems of the intake valves. Some
of this oil is sucked into the combustion chamber together with
the intake air and is burned along with the fuel. High temperature
exhaust gases also burn the oil used to lubricate the exhaust valve
stems.The amount of engine oil consumed depends on the viscosity of
the oil, the quality of the oil and the way the vehicle is driven.
More oil is consumed by highspeed driving and frequent
acceleration and deceleration.
A new engine consumes more oil, since its pistons, piston rings and
cylinder walls have not become conditioned.
When judging the amount of oil consumption, keep in mind that
the oil may have become diluted, making it difficult to judge the
true level accurately.
For example, if a vehicle is used for repeated short trips and
consumes a normal amount of oil, the dipstick may not show any
drop in the oil level at all, even after 1000 km (600 miles) or more.
This is because the oil is gradually becoming diluted with fuel or
moisture, making it appear that the oil level has not changed.
The diluting ingredients evaporate out when the vehicle is then
driven at high speeds, as on an expressway, making it appear that oil
is excessively consumed after driving at high speeds.
Importance of engine oil level check
One of the most important points in proper vehicle maintenance is
to keep the engine oil at the optimum level so that oil function will
not be impaired. Therefore, it is essential that the oil level be
checked regularly. Lexus recommends that the oil level be checked
every time you refuel the vehicle.
NOTICE

ENGINE
230Failure to check the oil level regularly could lead to serious
engine trouble due to insufficient oil.
For detailed information on oil level check, see ”Checking the
engine oil level” on page 230.
USED ENGINE OIL
CAUTION
Used engine oil contains potentially harmful contaminants
which may cause skin disorders such as inflammation or
skin cancer, so care should be taken to avoid prolonged and
repeated contact with it. To remove used engine oil from
your skin, wash thoroughly with soap and water.
Do not leave used oil within the reach of children.
Dispose of used oil and used oil filters only in a safe and
acceptable manner. Do not dispose of used oil and used oil
filters in household trash, in sewers or onto the ground.
Call your Lexus dealer or a service station for information
concerning recycling or disposal.
CHECKING THE ENGINE OIL
LEVEL
62L004-4
With the engine at operating temperature and turned off, check
the oil level on the dipstick.
1. To get a true reading, the vehicle should be on a level spot. After
turning off the engine, wait a few minutes for the oil to drain back
into the bottom of the engine.
2. Pull out the dipstick, and wipe it clean with a rag.
3. Reinsert the dipstick and push it in as far as it will go, or the
reading will not be correct.

ENGINE
231
62L002-1
1
Add oil 2
O.K. 3
Too full
4. Pull the dipstick out and look at the oil level on the end. If it is
between the full line (
5
) and the low line ( 4
), it is O.K.
62L003-3
If the oil level is below or only slightly above the low line, add
engine oil of the same type as already in the engine.Remove the oil filler cap and add engine oil a little at a time, checking
the dipstick. The approximate quantity of oil needed to fill between
the low line and the full line on the dipstick is indicated below for
reference.
When the level reaches within the correct range, return the filler cap
and turn the cap clockwise until you hear a click.
Oil quantity. L (qt., lmp. qt.) 1.5 (1.6, 1.3)
NOTICE
Avoid overfilling, or the engine could be damaged. Check the oil
level on the dipstick once again after adding the oil.

ENGINE
232
Engine oil selection
Use API SH, ”EnergyConserving II” or SJ, ”EnergyConserving”
multigrade engine oil or ILSAC multigrade engine oil.
Recommended viscosity (SAE):
62L0051
Temperature range anticipated before next oil change
SAE 5W30 is the best choice for your vehicle, for good fuel
economy, and good starting in cold weather.
If you use SAE 10W30 engine oil in extremely low
temperatures, the engine may become difficult to start, so SAE
5W30 engine oil is recommended.
Oil identification marks
62L0061
API Service Symbol
ILSAC Certification Mark
Either or both API registered marks are added to some oil containers
to help you select the oil you should use.
The API Service Symbol is located anywhere on the outside of the
container.
The top portion of the label shows the oil quality by API
(American Petroleum Institute) designation such as SJ. The
center portion of the label shows the SAE viscosity grade such as
SAE 5W30. ”EnergyConserving”, shown in the lower portion,
indicates that the oil has fuelsaving capabilities.
The ILSAC (International Lubricant Standardization and
Approval Committee) Certification Mark is displayed on the
front of the container.

CHASSIS
237
SPECIFICATIONS
AUTOMATIC TRANSMISSION
Fluid capacity
Drain and refill
Fluid type
1.9 L (2.0 qt., 1.7 lmp.qt.)
Automatic transmission fluid Type T IV or equivalent
DIFFERENTIAL
Oil capacity
Oil type
Oil viscosity
1.3 L (1.4 qt., 1.1 lmp.qt.)
Hypoid gear oil API GL5
Above 18C (0F): SAE 90
Below 18C (0F): SAE 80W or SAE 80W90
BRAKES
Pedal clearance
Pedal freeplay
Brake pad wear limit
Parking brake lining wear limit
Parking brake adjustment
Fluid type
70 mm (2.8 in.) Min. *1
1 6 mm (0.04 0.24 in.)
1.0 mm (0.04 in.)
1.0 mm (0.04 in.)
5 7 clicks *
2
SAE J1703 or FMVSS No. 116 DOT 3
*1: Minimum pedal clearance when depressed with the pressure of 490 N (50 kgf, 110 lbf.) with the engine running
*
2: Parking brake adjustment when depressed with the pressure of 294 N (30 kgf, 66.1 lbf.)