1998 HONDA CIVIC codes

[x] Cancel search: codes

fuel pump jump cable height adjustment key buttons lights

Load previous 8 pages

Page 24 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Chassis and Paint Codes
Vehicle Grade
2: DX, HX
4: EX
5: EX With ABS, Si
Check Digit
Model Year
X:1999
Factory Code
L: East Liberty, Ohio Plant, U.S.A.Serial Number
Vehicle ldentification Number
and F

Page 26 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Ghassis and Paint Codes
Vehicle Grade
0: EX
3: LX
4: LX with ABS
5: LX with ABS and lVC
7: EX with ABS
8: EX with ABS and AyC
Ch6ck Digit
Model Year
X: 1999
Factory Code
CANADA 1999 Model (4-door Sed

Page 28 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Chassis and Paint Codes
Vohicle Grade
2: CX
4: DX
Check Digit
Model Yeal
Y: 2000
Fastory Code
H: Alliston Plant, Ontario. Canada
Serial Number
Vehicle ldentification NumbeI
and Federal Motor Vehicle
S

Page 30 of 2189

$HONDA CIVIC 1998 6.G Workshop Manual Chassis and Paint Codes U.S.2000 Model (2-door Coupe) Vehicle ldentification Number l HG EJ6 12 *Y1000001 Manufacturer. Make and Type ol Vehicle1HG: HONDA OF AMERICA t\4FG., tNC. HONDA Passenger Vehi$

Page 32 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Chassis and Paint Codes
Vehicle Grade
0: EX
1: LX-V
2: LX-V with ABS
3: LX
4: LX with ABS
5: LX with ABS and lyC
7: EX with ABS
8; EX with ABS and A,,/C
Check Digit
Model Y€ar
Y: 2000
Factory Code

Page 207 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Main Bearing
Selection
CAUTION: lf the codes are indecipherable because of anaccumulation of dirt and dust, do not scrub them with a
wire brush or scraper. Clean them only with solvent ol
deiergent.
C

Page 208 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Connecting Rod Bearings
Clearance
Remove the connecting rod cap and bearing half
Clean the crankshaft rod iournal and bearing half
with a clean shop towel.
Place plastigage across the rod journal.
Rei

Connecting Rod Bearings
Clearance
Remove the connecting rod cap and bearing half
Clean the crankshaft rod iournal and bearing half
with a clean shop towel.
Place plastigage across the rod journal.
Reinstall the bearing half and cap, and torque the nuts.
Torque
Bl6A2 engine:
40 N.m (4.1 kgl.m, 30 lbf'ft)
Dr6Y5, D16Y7, D16Y8 enginss:
31 N'm (3.2 kgf.m, 23 lbf ftl
NOTE| Do not rotate the crankshaft during inspection.
Remove the rod cap and bearing half and measure
the widest part of the plastigage.
Connecting Rod Bearing-to.Journal Oil Glearance:
816A2 engine:
Standard lNewl: 0.032 - 0.050 mm
10.0013 - 0.0020 in)
Service Limit: 0.06 mm 10.002 inl
D16Y5, D16Y7, D16Y8 engines:
Standard lNew): 0.020 - 0.038 mm
(0.0008 - 0.0015 in)
Service Limit 0.05 mm 10.002 inl
'1.
4.
lf the plastigage measures too wide or too narrow'
remove the upper half of the bearing, install a new,
complete bearing with the same color code (select
the color as shown in the right column), and
recheck the clearance.
CAUTION: Do not lile, shim, or scrape the bearings
or the caps to adiust clgarance.
lf the plastigage shows the clearance is still incorrect.
try the next larger or smaller bearing (the color listed
above or below that one), and check clearance again.
NOTE: lf the Droper clearance cannot be obtained
by using the appropriate larger or smaller bearings,
replace the crankshaft and start over.
PLASTIGAGE STRIP
\
7.
7-11
Selection
CAUTION: lf the codes are indecipherable because of
an accumulation of dirt and dust, do not sclub them
with a wile brush or scraper. Clean them only with sol-
vent or detergent,
Connecting Rod Code Location
Numbers have been stamped on the side of each con
necting rod as a code for the size of the big end Use
them, and the letters stamped on the crankshaft (codes
for rod journal size), to choose the correct bearlngs
Half of number ls
stamped on bearingcap and the otherhalf is stamped onrod.
Bearing ldentilication
Color code is on theedge ofthe bearing.
lfA--;T] |
lle"'tt l;llcorlll ll
I lD;;ilril |l-l
Larger brg end bore
Smaller Smallerrod bearlngjournal (thicker)
---------------- Smallerbearing{thrcker)
RedPinkGreen
PinkGreen
GreenErownBlack
GreenBrownBlackBlue
1234
Connecting Rod Journal Code Locations (Lettels)

Page 350 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Troubleshooting
Troubleshooting Procedures
How To Begin Troubleshooting
When the Malfunction Indicator Lamp (MlL) has been reported on, or there is a driveability problem, use the appropr-
ate oroced

Load next 8 pages

Page: < prev 1-8 9-16 17-24 25-32 33-40 40 next >

tire pressure reset refuelling trunk fold seats wiper size brake