1998 FORD WINDSTAR lock

218
%*
[GF06300(ALL)05/96]
Driving
[GF06400(ALL)01/96]
When to use N (Neutral)
*
[GF06500(ALL)09/95]
In N (Neutral), the wheels of the transaxle are not locked. Your
vehicle will roll freely, even on the slightest incline, unless the
parking brake or brakes are on.
[GF06600(ALL)01/96]
When to use
jOverdrive
[GF06700(ALL)01/96]
Overdrive is the normal driving position. When the gearshift
lever is placed in
jOverdrive, and the Overdrive Off button
has not been pressed, the vehicle will automatically upshift to
second, third and fourth gears. The transaxle will shift into the
correct gear when the right speed is reached.
% [GF06800(ALL)01/96]
When to use D (Drive) Ð with the Overdrive Off button
activated
[GF06900(ALL)01/96]
You will notice that there is only one drive position on your
gearshift indicator (instead of Drive and Overdrive). However,
you will find a button and an indicator light located on the
gearshift lever. Push in the button on the end of the lever and
the OVERDRIVE OFF light on the end of the gearshift lever will
illuminate. With the OVERDRIVE OFF light illuminated, the
transaxle will operate in first, second and third gears and will
not shift into fourth gear. Operating in Drive (OVERDRIVE OFF
light illuminated) provides more engine braking than Overdrive
for descending hills or city driving.
[GF07000(ALL)01/96]
6 pica art:0050058-A
Overdrive button location
File:09wngfs.ex
Update:Mon Oct 7 11:46:08 1996

Driving
219
[GF07100(ALL)01/96]
To return the transaxle to the normal Overdrive operation, press
the OVERDRIVE ON/OFF button again. Use this button to
select Overdrive or Overdrive Off whenever you drive your
vehicle.
*
[GF07200(ALL)01/96]
The transaxle will be in the ªoverdrive onº mode when the
vehicle is started even if the O/D OFF mode was selected when
the vehicle was last shut off.
*
[GF07300(ALL)01/96]
NOTE: If the O/D OFF indicator light is flashing on and off
repeatedly when the vehicle is started, there is a
transaxle electronic system malfunction. Contact your
dealer as soon as possible.
*
[GF07400(ALL)05/96]
When to use 2 (Second)
[GF07500(ALL)01/96]
Use 2 (Second) when driving on slippery roads or to provide
additional engine braking on downgrades. This position
provides Second and First gear operation only.
*
[GF07600(ALL)01/96]
When to use 1 (First)
[GF07700(ALL)05/96]
Use 1 (First) to provide maximum engine braking on steep
downgrades. Upshifts from First can be made by manually
shifting to 2 (Second) or
j(Overdrive). 1 (First) gear provides
only first gear operation. If you select First while driving at
higher speeds, the transaxle will shift to 2 (Second), and then
downshift to 1 (First) after the vehicle decelerates to the proper
speed.
*
[GF07800(ALL)01/96]
Parking
*
[GF07900(ALL)01/96]
Always come to a complete stop before you shift into P (Park).
This position locks the transaxle and prevents the front wheels
from turning. To securely latch the gearshift in the P (Park)
position, pull it toward you, push it completely
counterclockwise against the stop, and then push it toward the
instrument panel.
File:09wngfs.ex
Update:Mon Oct 7 11:46:08 1996

220
[GF08000(ALL)01/96]
The gearshift is securely latched in P (Park) if you can not
rotate it in a clockwise direction without pulling it toward you.
*
[GF08100(ALL)05/96]
RWARNING
Always set the parking brake fully and make sure the
gearshift is latched in P (Park). Turn off the ignition
whenever you leave your vehicle.
*
[GF08200(ALL)05/96]
RWARNING
Never leave your vehicle unattended while it is running.
*
[GF08300(ALL)05/96]
Forced Downshifts
[GF08400(ALL)01/96]
To gain extra acceleration in
j(Overdrive) (when passing
another vehicle) push the accelerator to the floor. The transaxle
will automatically downshift to the appropriate gear (third,
second or first).
*
[GF08500(ALL)01/96]
Vehicle Loading Information
*
[GF08600(ALL)01/96]
Your vehicle's load capacity is designated by weight, not
volume, so you cannot necessarily use all the available space.
Maximum safe vehicle weights as well as tire sizes, rim sizes
and inflation pressures are specified for your vehicle at the
assembly plant on the Safety Compliance Certification Label.
The certification label is located on the pillar in the driver's
door opening.
*
[GF08700(ALL)01/96]
Each additional item of equipment affects how much cargo a
vehicle can carry. If a vehicle is overloaded, performance will
suffer and service concerns may arise.
*
[GF08800(ALL)01/96]
NOTE: The vehicle must not be loaded to both the front and
rear GAWR because the GVWR will be exceeded. The
GAWR of the front and rear axles exceed the GVWR
when added together.
File:09wngfs.ex
Update:Mon Oct 7 11:46:08 1996

230
[GF17600(ALL)12/95]
10-1/2 pica
art:0050032-B
The adjustable cross-bar
%*
[GF17700(ALL)01/96]
Driving Under Special Conditions
%*
[GF17800(ALL)01/96]
Tips for Safe Driving
[GF17900(ALL)04/96]
As with any new vehicle, yours may drive and handle
differently from your previous vehicle. Use greater care until
you become accustomed to its features and driving
characteristics.
[GF18000(ALL)04/96]
Always operate your vehicle within reasonable limits. Abrupt
changes in acceleration, deceleration, turning, or combinations of
these maneuvers can cause a vehicle to behave differently than
anticipated, especially when road conditions vary.
[GF18100(ALL)04/96]
For example, even with anti-lock brakes, extreme braking can
make it difficult to control the direction of the vehicle. Use a
ªsqueezeº technique. Push on the brake pedal with steadily
increasing force. This allows the wheels to brake, yet continue to
roll so that you may steer in the direction you want to travel.
[GF18200(ALL)04/96]
If you release the accelerator abruptly or brake hard while
going too fast around a severe curve, your vehicle may change
its direction of travel. Avoid applying the brakes, if possible. If
you must apply the brakes, use the ªsqueezeº technique
described earlier.
File:09wngfs.ex
Update:Mon Oct 7 11:46:08 1996

232
[GF19800(ALL)09/96]
RWARNING
To avoid skidding and losing control on slippery roads,
do not downshift into 1 (First) when you are moving
faster than 20 mph (32 km/h).
[GF19900(ALL)04/96]
RWARNING
The Anti-Lock Brake System may not prevent brake
lock-up on extremely slippery surfaces.
%*
[GF20000(ALL)01/96]
High water
*
[GF20100(ALL)01/96]
Do not drive through flooded areas unless you are sure that the
water is below the bottom of the wheel hubs.
[GF20200(ALL)04/96]
If you must drive through high water, drive slowly. You may
have limited traction or wet brakes so allow extra stopping
distance because your vehicle will not stop as quickly as usual.
[GF20300(ALL)04/96]
After you drive through the standing water, apply your brakes
gently several times as your vehicle moves slowly to help dry
the brakes.
*
[GF20400(ALL)05/96]
Rocking the Vehicle
[GF20500(ALL)04/96]
If your vehicle gets stuck (for example, in mud or snow), you
may rock it out. Shift in a steady rhythm between forward and
reverse gears. At the same time, press lightly on the accelerator.
If you are still stuck after a few minutes of rocking, call for a
tow truck.
[GF20600(ALL)01/96]
NOTE: If your vehicle is equipped with Traction Control,
make sure the system has been turned off before
attempting to rock the vehicle.
[GF20700(ALL)07/96]
SeeTraction Control Off Lightin theInstrumentationsection of
this guide for more information.
File:09wngfs.ex
Update:Mon Oct 7 11:46:08 1996

Roadside Emergencies
249
[ER06800(ALL)01/96]
Removing the spare tire
*
[ER06900(ALL)01/96]1.
Open the liftgate and find the plastic hex nut cover in the
carpeting of the cargo area. Lift the cover to expose the hex
nut.
[ER07000(ALL)01/96]
17-1/2 pica
art:0050024-B
The spare tire cover
*
[ER07100(ALL)05/96]2.
Find the lug wrench in the tool kit located behind the jack in
the right cargo area side panel.
*
[ER07200(ALL)01/96]3.
Fit the hex-shaped end of the lug wrench over the hex nut
in the floor of the cargo area. Turn counterclockwise until
the cable extends far enough to lower the spare tire to the
ground.
File:10wners.ex
Update:Mon Oct 7 11:47:52 1996

250
*
[ER07300(ALL)01/96]
10-1/2 pica
art:0040172-B
The spare tire in the lowered position
*
[ER07400(ALL)01/96]4.
Continue to turn the hex nut counterclockwise until the
spare tire retainer can be seen for removal.
*
[ER07500(ALL)01/96]5.
Remove the retainer from the center of the wheel. It may be
necessary to lift one end of the tire to disengage the retainer.
[ER07510(ALL)10/96]
16" wheels only: Lift one end of the tire and separate wheel
retainer from the cable.
*
[ER07600(ALL)01/96]
10-1/2 pica
art:0040173-B
Removing the spare tire retainer
File:10wners.ex
Update:Mon Oct 7 11:47:52 1996

Roadside Emergencies
251
% [ER07700(ALL)04/96]
Changing the Tire
*
[ER07800(ALL)01/96]
You should only raise your vehicle with a jack properly placed
at the front or rear jacking points.
*
[ER07900(ALL)05/96]1.
Make sure that your vehicle will not move or roll and that
the tires and jack are on a level, solid surface. Put the
gearshift lever in P (Park). Set the parking brake and block
the wheel Ð in both directions Ð that is diagonally opposite
the tire that you are changing.
*
[ER08000(ALL)01/96]
RWARNING
When one of the front wheels is off the ground, the
transaxle alone will not prevent the vehicle from moving
or slipping off the jack, even if the vehicle is in P (Park).
*
[ER08100(ALL)01/96]
RWARNING
To prevent the vehicle from moving when you change a
tire, be sure the parking brake is set, then block (in both
directions) the wheel that is diagonally opposite (other
side and end of the vehicle) to the tire being changed.
*
[ER08200(ALL)03/96]
RWARNING
If the vehicle slips off the jack, you or someone else
could be seriously injured.
*
[ER08300(ALL)01/96]
RWARNING
On vehicles equipped with Air Suspension, turn OFF the
Air Suspension switch prior to jacking, hoisting or
towing your vehicle.
File:10wners.ex
Update:Mon Oct 7 11:47:52 1996