Safety belt maintenance
Inspect the safety belt systems periodically to make
sure they work properly and are not damaged.
Inspect the safety belts to make sure there are no
nicks, wears or cuts, replacing if necessary. All
safety belt assemblies, including retractors, buckles,
front seat belt buckle assemblies (slide bar)(if
equipped), shoulder belt height adjusters (if
equipped), child safety seat tether bracket
assemblies (if equipped), and attaching hardware,
should be inspected after a collision. Ford
recommends that all safety belt assemblies used in
vehicles involved in a collision be replaced. However,
if the collision was minor and a qualified technician
finds that the belts do not show damage and
continue to operate properly, they do not need to be
replaced. Safety belt assemblies not in use during a
collision should also be inspected and replaced if
either damage or improper operation is noted.
Failure to inspect and if necessary replace
the safety belt assembly under the above
conditions could result in severe personal injuries
in the event of a collision.
Refer toCleaning and maintaining the safety
beltsin theMaintenance and caresection.
AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM
(SRS)
Seating and safety restraints
71
Vertical aim adjustment
1. Park the vehicle on
a level surface
approximately
7.6 meters (25 feet)
from a vertical wall or
screen directly in front
of it.
2. Measure the height
from the center of your
headlamp to the
ground and mark an
2.4 meters (8 foot)
horizontal reference line on the vertical wall or
screen at this height (a piece of masking tape works
well). The center of the lamp is marked by a 3.0 mm
circle on the headlamp lens.
3. Turn on the low beam headlamps to illuminate the
wall or screen and open the hood.
4. On the wall or screen you will observe a distinct
line of high intensity light. If this is not centered on
the horizontal reference line, the beam will need to
be adjusted.
5. Locate the vertical adjuster on each headlamp,
then usea6mmwrench or screwdriver to turn the
adjuster either counterclockwise (to adjust up) or
clockwise (to adjust down) centering the light on
the horizontal reference line.
6. HORIZONTAL AIM IS NOT REQUIRED FOR THIS
VEHICLE AND IS NON-ADJUSTABLE.
7. Close the hood and turn off the lamps.
CLEANING AND CARING FOR YOUR VEHICLE
Refer to the ªCustomer Assistance Guideº for a list
of Ford-approved cleaners, polishes and waxes.
Maintenance and care
171
ENGINE DATA
Engine 3.8L OHV V6
engine4.6L SOHC V8
engine
Cubic inches 232 281
Horsepower 190 @
5250 rpm260 @
5250 rpm
Torque 220 lb.-ft. @
2750 rpm302 lb.-ft. @
4000 rpm
Recommended
fuel87 octane 87 octane
Firing order 1-4-2-5-3-6 1-3-7-2-6-5-4-8
Spark plug gap 1.3-1.4 mm
(0.052-
00.056 inch)1.3-1.4 mm
(0.052-
00.056 inch)
Ignition system EDIS Coil on plug
Compression
ratio9.4:1 9.0:1
VEHICLE DIMENSIONS
Vehicle
dimensionsCoupe
mm (in)Convertible
mm (in)
(1) Overall
length4 653.3 (183.2) 4 653.3 (183.2)
(2) Overall
width1 856.7 (73.1) 1 856.7 (73.1)
(3) Overall
height1 353.8 (53.3)
11 356.4 (53.4)2
(4) Wheelbase 2 573.0 (101.3) 2 573.0 (101.3)
(5) Track - Front1 534.2 (60.4)31 534.2 (60.4)3
(5) Track - Rear1 539.2 (60.6)41 539.2 (60.6)4
1
1 358.9 mm (53.5 in) for Mustang GT
21 361.4 mm (53.6 in) for Mustang GT
31 521.5 mm (59.9 in) for Mustang GT
41 526.5 mm (60.1 in) for Mustang GT
Capacities and specifications
182
