1998 DODGE RAM 1500 tire pressure

STANDARD PROCEDURE
STANDARD PROCEDURE - HANDLING TUBING
AND FITTINGS
CAUTION: The system must be completely empty
before opening any fitting or connection in the
refrigeration system. Open fittings with caution
even after the system has been emptied. If any
pressure is noticed as a fitting is loosened,
retighten fitting and evacuate the system again.
A good rule for the flexible hose lines is to keep the
radius of all bends at least 10 times the diameter of
the hose. Sharper bends will reduce the flow of
refrigerant. The flexible hose lines should be routed
so they are at least 3 inches (80 mm) from the
exhaust manifold. Inspect all flexible hose lines to
make sure they are in good condition and properly
routed.
The use of correct wrenches when making connec-
tions is very important. Improper wrenches or
improper use of wrenches can damage the fittings.
The internal parts of the A/C system will remain sta-
ble as long as moisture-free refrigerant and refrig-
erant oil is used. Abnormal amounts of dirt,
moisture or air can upset the chemical stability.
This may cause operational troubles or even seri-
ous damage if present in more than very small
quantities. Before disconnecting a component,
clean the outside of the fittings thoroughly to pre-
vent contamination from entering the refrigerant
system.
When opening a refrigeration system, have every-
thing you will need to repair the system ready. This
will minimize the amount of time the system must
be opened. Cap or plug all lines and fittings as
soon as they are opened. This will help prevent the
entrance of dirt and moisture. All new lines and
components should be capped or sealed until they
are ready to be used. Before connecting a compo-
nent, clean the outside of the fittings thoroughly to
prevent contamination from entering the refrigerant
system.
All tools, including the refrigerant dispensing mani-
fold, the manifold gauge set, and test hoses should
be kept clean and dry.
Kinks in the refrigerant tubing or sharp bends in
the refrigerant hose lines will greatly reduce the
capacity of the entire system. High pressures are pro-
duced in the system when it is operating. Extreme
care must be exercised to make sure that all connec-
tions are pressure tight. Dirt and moisture can enter
the system when it is opened for repair or replace-
ment of lines or components. The refrigerant oil willabsorb moisture readily out of the air. This moisture
will convert into acids within a closed system.
STANDARD PROCEDURE - DIODE
REPLACEMENT
(1) Disconnect and isolate the battery negative
cable. If the vehicle has dual batteries, remove the
negative cable from both batteries.
(2) Locate the diode in the harness, and remove
the protective covering.
(3) Remove the diode from the harness. Note the
direction of current flow (Fig. 1).
(4) Remove the insulation from the wires in the
harness. Only remove enough insulation to solder in
the new diode.
(5) Install the new diode in the harness, making
sure current flow is correct. If necessary refer to the
appropriate wiring diagram for current flow.
(6) Solder the connections together using rosin
core type solder only.Do not use acid core solder.
(7) Tape the diode to the harness using electrical
tape. Make sure the diode is completely sealed from
the elements.
(8) Reconnect the battery negative cable(s) and
test the affected systems.
Fig. 1 Diode Identification
1 - CURRENT FLOW
2 - BAND INDICATES CURRENT FLOW
3 - DIODE AS SHOWN IN WIRING DIAGRAMS
DRPLUMBING 24 - 45
PLUMBING (Continued)

After the system has been tested for leaks and
evacuated, a refrigerant (R-134a) charge can be
injected into the system.
NOTE: When connecting the service equipment
coupling to the line fitting, verify that the valve of
the coupling is fully closed. This will reduce the
amount of effort required to make the connection.
(1) If using a separate vacuum pump close all
valves before disconnecting pump. Connect manifold
gauge set to the A/C service ports.
NOTE: Always refer to the underhood HVAC Speci-
fication label for the refrigerant fill level of the vehi-
cle being serviced.
(2) Measure refrigerant (refer to capacities). Refer
to the instructions provided with the equipment
being used.
(3) Verify engine is shut off. Open the suction and
discharge valves. Open the charge valve to allow the
refrigerant to flow into the system. When the trans-
fer of refrigerant has stopped, close the suction and
discharge valve.
(4) If all of the charge did not transfer from the
dispensing device, put vehicle controls into the fol-
lowing mode:
²Automatic transmission in park or manual
transmission in neutral
²Engine at idle
²A/C mode control set to outside air
²A/C mode control set to panel mode
²A/C temperature control set to full cool
²Blower motor control set on highest speed
²Vehicle windows closed
If the A/C compressor does not engage, test the
compressor clutch control circuit and correct any fail-
ure (Refer to 8 - ELECTRICAL/WIRING DIAGRAM
INFORMATION - DIAGNOSIS AND TESTING).
(5) Open the suction valve to allow the remaining
refrigerant to transfer to the system.
WARNING: TAKE CARE NOT TO OPEN THE DIS-
CHARGE (HIGH-PRESSURE) VALVE AT THIS TIME.
(6) Close all valves and test the A/C system perfor-
mance.
(7) Disconnect the charging station or manifold
gauge set. Install the service port caps.
REFRIGERANT CHARGE CAPACITY
The R-134a refrigerant system charge capacity for
this vehicle can be found on the underhood HVAC
specfication tag.
A/C COMPRESSOR
DESCRIPTION
DESCRIPTION - A/C COMPRESSOR
The A/C system on models equipped with the 5.9L
engine use a Sanden SD-7 reciprocating swash plate-
type compressor. This compressor has a fixed dis-
placement of 165 cubic centimeter (10.068 cubic
inches) and has both the suction and discharge ports
located on the cylinder head.
The A/C system on models equipped with the 3.7L,
4.7L and 5.7L engines use a Denso 10S17 reciprocat-
ing swash plate-type compressor. This compressor
has a fixed displacement of 170 cubic centimeter and
has both the suction and discharge ports located on
the cylinder head.
A label identifying the use of R-134a refrigerant is
located on both A/C compressors.
DESCRIPTION - HIGH PRESSURE RELIEF
VALVE
A high pressure relief valve is located on the com-
pressor cylinder head, which is on the rear of the
compressor. This mechanical valve is designed to
vent refrigerant from the system to protect against
damage to the compressor and other system compo-
nents, caused by condenser air flow restriction or an
overcharge of refrigerant.
OPERATION
OPERATION - A/C COMPRESSOR
The A/C compressor is driven by the engine
through an electric clutch, drive pulley and belt
arrangement. The compressor is lubricated by refrig-
erant oil that is circulated throughout the refrigerant
system with the refrigerant.
The compressor draws in low-pressure refrigerant
vapor from the evaporator through its suction port. It
then compresses the refrigerant into a high-pressure,
high-temperature refrigerant vapor, which is then
pumped to the condenser through the compressor dis-
charge port.
The compressor cannot be repaired. If faulty or
damaged, the entire compressor assembly must be
replaced. The compressor clutch, pulley and clutch
coil are available for service.
OPERATION - HIGH PRESSURE RELIEF VALVE
The high pressure relief valve vents the system
when a discharge pressure of 3445 to 4135 kPa (500
to 600 psi) or above is reached. The valve closes
24 - 48 PLUMBINGDR
PLUMBING (Continued)

FRONT SERVO - DESCRIPTION.........21-208
FRONT SERVO - DISASSEMBLY........21-209
FRONT SERVO - INSPECTION..........21-209
FRONT SERVO - OPERATION..........21-208
FRONT SKID PLATE - INSTALLATION.....13-23
FRONT SKID PLATE - REMOVAL.........13-23
FRONT SUSPENSION - DESCRIPTION,
GEAR - INDEPENDENT................19-17
FRONT SUSPENSION - INSTALLATION,
GEAR - INDEPENDENT................19-18
FRONT SUSPENSION - REMOVAL, GEAR
- INDEPENDENT.....................19-17
FRONT SUSPENSION, SPECIAL TOOLS....2-12
FRONT TOW HOOK ASSEMBLY -
INSTALLATION.......................13-23
FRONT TOW HOOK ASSEMBLY -
REMOVAL..........................13-23
FRONT WHEEL SPEED SENSOR -
DESCRIPTION........................5-47
FRONT WHEEL SPEED SENSOR -
INSTALLATION........................5-48
FRONT WHEEL SPEED SENSOR -
OPERATION..........................5-47
FRONT WHEEL SPEED SENSOR -
REMOVAL...........................5-48
FRONT WHEELHOUSE SPLASH SHIELD -
INSTALLATION.......................23-41
FRONT WHEELHOUSE SPLASH SHIELD -
REMOVAL..........................23-41
FUEL CONTROL ACTUATOR -
DESCRIPTION.......................14-74
FUEL CONTROL ACTUATOR -
OPERATION.........................14-74
FUEL CONTROL ACTUATOR - REMOVAL . . . 14-74
FUEL DELIVERY - GAS - DESCRIPTION....14-1
FUEL DELIVERY - GAS - OPERATION......14-2
FUEL DRAIN CIRCUIT - OPERATION......14-67
FUEL FILL DOOR - INSTALLATION.......23-39
FUEL FILL DOOR - REMOVAL...........23-39
FUEL FILLER CAP - DESCRIPTION.......25-13
FUEL FILLER CAP - OPERATION.........25-13
FUEL FILTER - STANDARD
PROCEDURES, WATER DRAINING AT.....14-47
FUEL FILTER / WATER SEPARATOR -
DESCRIPTION.......................14-50
FUEL FILTER / WATER SEPARATOR -
INSTALLATION.......................14-50
FUEL FILTER / WATER SEPARATOR -
OPERATION.........................14-50
FUEL FILTER / WATER SEPARATOR -
REMOVAL..........................14-50
FUEL FILTER/PRESSURE REGULATOR -
DESCRIPTION........................14-5
FUEL FILTER/PRESSURE REGULATOR -
OPERATION..........................14-6
FUEL GAUGE - DESCRIPTION...........8J-26
FUEL GAUGE - OPERATION.............8J-26
FUEL HEATER - DESCRIPTION..........14-51
FUEL HEATER - DIAGNOSIS AND
TESTING...........................14-52
FUEL HEATER - OPERATION............14-51
FUEL HEATER RELAY - DESCRIPTION....14-52
FUEL HEATER RELAY - INSTALLATION....14-53
FUEL HEATER RELAY - OPERATION......14-52
FUEL HEATER RELAY - REMOVAL........14-52
FUEL INDICATOR - DESCRIPTION, LOW . . . 8J-30
FUEL INDICATOR - OPERATION, LOW.....8J-30
FUEL INJECTION PUMP - DESCRIPTION . . 14-53
FUEL INJECTION PUMP - INSTALLATION . . 14-55
FUEL INJECTION PUMP - OPERATION....14-53
FUEL INJECTION PUMP - REMOVAL......14-54
FUEL INJECTION PUMP TIMING -
DIAGNOSIS AND TESTING.............14-53
FUEL INJECTOR - DESCRIPTION....14-26,14-74
FUEL INJECTOR - INSTALLATION........14-77
FUEL INJECTOR - OPERATION.....14-26,14-74
FUEL INJECTOR - REMOVAL............14-75
FUEL INJECTOR FIRING ORDER, DIESEL . . 14-48
FUEL INJECTOR RAIL - DESCRIPTION....14-78
FUEL INJECTOR RAIL - INSTALLATION....14-78
FUEL INJECTOR RAIL - OPERATION
......14-78
FUEL INJECTOR RAIL - REMOVAL
.......14-78
FUEL LEVEL SENDING UNIT / SENSOR -
DESCRIPTION
...................14-57,14-6
FUEL LEVEL SENDING UNIT / SENSOR -
INSTALLATION
........................14-7
FUEL LEVEL SENDING UNIT / SENSOR -
OPERATION
.....................14-57,14-6FUEL LEVEL SENDING UNIT / SENSOR -
REMOVAL...........................14-7
FUEL LINE LEAKS - DIAGNOSIS AND
TESTING, HIGH-PRESSURE.............14-58
FUEL LINES - DESCRIPTION........14-57,14-7
FUEL LINES - INSTALLATION...........14-60
FUEL LINES - OPERATION..............14-57
FUEL LINES - REMOVAL...............14-58
FUEL PRESSURE LIMITING VALVE -
DESCRIPTION.......................14-61
FUEL PRESSURE LIMITING VALVE -
INSTALLATION.......................14-61
FUEL PRESSURE LIMITING VALVE -
OPERATION.........................14-61
FUEL PRESSURE LIMITING VALVE -
REMOVAL..........................14-61
FUEL PRESSURE SENSOR -
DESCRIPTION.......................14-60
FUEL PRESSURE SENSOR -
INSTALLATION.......................14-61
FUEL PRESSURE SENSOR - OPERATION . . 14-60
FUEL PRESSURE SENSOR - REMOVAL....14-60
FUEL PUMP - DESCRIPTION............14-11
FUEL PUMP - OPERATION.............14-11
FUEL PUMP MODULE - DESCRIPTION....14-11
FUEL PUMP MODULE - INSTALLATION . . . 14-12
FUEL PUMP MODULE - OPERATION......14-11
FUEL PUMP MODULE - REMOVAL.......14-12
FUEL PUMP RELAY - DESCRIPTION......14-27
FUEL PUMP RELAY - INSTALLATION.....14-28
FUEL PUMP RELAY - OPERATION........14-27
FUEL PUMP RELAY - REMOVAL.........14-28
FUEL PUMP RELAYS - DIAGNOSIS AND
TESTING, ASD........................8I-5
FUEL RAIL - DESCRIPTION.............14-12
FUEL RAIL - INSTALLATION............14-15
FUEL RAIL - OPERATION...............14-12
FUEL RAIL - REMOVAL................14-13
FUEL REQUIREMENTS - DIESEL ENGINE
- DESCRIPTION........................0-1
FUEL SENSOR - DESCRIPTION, WATER
IN ................................14-66
FUEL SENSOR - OPERATION, WATER IN . . 14-66
FUEL SENSOR - REMOVAL, WATER IN....14-66
FUEL SYSTEM - DESCRIPTION, DIESEL . . . 14-45
FUEL SYSTEM - DIESEL ENGINE -
TORQUE............................14-48
FUEL SYSTEM - EXCEPT DIESEL -
TORQUE............................14-3
FUEL SYSTEM PARTS - STANDARD
PROCEDURES, CLEANING..............14-47
FUEL SYSTEM PRESSURE RELEASE -
STANDARD PROCEDURE................14-2
FUEL SYSTEM PRESSURE,
SPECIFICATIONS......................14-3
FUEL SYSTEM PRIMING - STANDARD
PROCEDURE........................14-47
FUEL SYSTEM, SPECIAL TOOLS..........14-5
FUEL SYSTEM, SPECIAL TOOLS -
DIESEL............................14-49
FUEL TANK - DESCRIPTION............14-17
FUEL TANK - OPERATION..............14-17
FUEL TANK MODULE - DESCRIPTION.....14-63
FUEL TANK MODULE - INSTALLATION....14-64
FUEL TANK MODULE - OPERATION......14-63
FUEL TANK MODULE - REMOVAL........14-63
FUEL TRANSFER PUMP - DESCRIPTION . . 14-64
FUEL TRANSFER PUMP - INSTALLATION . . 14-65
FUEL TRANSFER PUMP - OPERATION....14-64
FUEL TRANSFER PUMP - REMOVAL......14-64
FULL SIZE, SPARE WHEEL WITH
MATCHING TIRE - DESCRIPTION........22-15
FUNCTIONS - DESCRIPTION, CIRCUIT . . 8W-01-6
FUSE - DESCRIPTION, IOD...........8W-97-6
FUSE - INSTALLATION, IOD..........8W-97-7
FUSE - OPERATION, IOD.............8W-97-6
FUSE - REMOVAL, IOD..............8W-97-7
FUSES POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON......8W-01-10
GAP AND FLUSH - SPECIFICATIONS......23-95
GAS ENGINE - DIAGNOSIS AND TESTING
. . 11-4
GAS ENGINE - INSTALLATION
...........19-26
GAS ENGINE - REMOVAL
..............19-25
GAS ENGINES - CLEANING, RADIATOR
FAN
................................7-34
GAS ENGINES - DESCRIPTION, COOLANT
RECOVERY CONTAINER
................7-33GAS ENGINES - INSPECTION, RADIATOR
FAN ................................7-34
GAS ENGINES - INSTALLATION,
COOLANT RECOVERY CONTAINER........7-33
GAS ENGINES - INSTALLATION,
RADIATOR FAN.......................7-34
GAS ENGINES - OPERATION, COOLANT
RECOVERY CONTAINER................7-33
GAS ENGINES - REMOVAL, COOLANT
RECOVERY CONTAINER................7-33
GAS ENGINES - REMOVAL, RADIATOR
FAN ................................7-33
GAS ENGINES - STANDARD
PROCEDURE, DRAINING COOLING
SYSTEM - ALL........................7-17
GAS ENGINES - STANDARD
PROCEDURE, REFILLING COOLING
SYSTEM - ALL........................7-18
GASKET - DIAGNOSIS AND TESTING,
CYLINDER HEAD......................9-21
GASKET FAILURE - DIAGNOSIS AND
TESTING, CYLINDER HEAD.............9-199
GASKET SELECTION - STANDARD
PROCEDURE, HEAD...................9-281
GASKET SURFACE PREPARATION -
STANDARD PROCEDURE, ENGINE........9-10
GASKETS AND SEALERS - STANDARD
PROCEDURE, FORM-IN-PLACE . . . 9-239,9-9,9-94
GAUGE - DESCRIPTION, ENGINE
TEMPERATURE......................8J-24
GAUGE - DESCRIPTION, FUEL...........8J-26
GAUGE - DESCRIPTION, OIL PRESSURE . . 8J-33
GAUGE - DESCRIPTION, VOLTAGE.......8J-42
GAUGE - OPERATION, ENGINE
TEMPERATURE......................8J-24
GAUGE - OPERATION, FUEL............8J-26
GAUGE - OPERATION, OIL PRESSURE....8J-33
GAUGE - OPERATION, VOLTAGE.........8J-43
GAUGES - DIAGNOSIS AND TESTING,
PRESSURE..........................22-7
GAUGES INDICATOR - DESCRIPTION,
CHECK.............................8J-21
GAUGES INDICATOR - OPERATION,
CHECK.............................8J-21
GEAR - DESCRIPTION, CRANKSHAFT.....9-273
GEAR - INDEPENDENT FRONT
SUSPENSION - DESCRIPTION...........19-17
GEAR - INDEPENDENT FRONT
SUSPENSION - INSTALLATION..........19-18
GEAR - INDEPENDENT FRONT
SUSPENSION - REMOVAL..............19-17
GEAR - INSTALLATION................9-273
GEAR - INSTALLATION, PINION
GEAR/RING......................3-51,3-77
GEAR - LINK/COIL - DESCRIPTION.......19-20
GEAR - LINK/COIL - INSTALLATION......19-21
GEAR - LINK/COIL - OPERATION........19-20
GEAR - LINK/COIL - REMOVAL..........19-20
GEAR - REMOVAL....................9-273
GEAR - REMOVAL, PINION GEAR/RING....3-49,
3-75
GEAR HOUSING - INSTALLATION........9-300
GEAR HOUSING - REMOVAL............9-299
GEAR HOUSING COVER - INSTALLATION . . 9-301
GEAR HOUSING COVER - REMOVAL
.....9-301
GEAR INPUT SHAFT SEAL -
INSTALLATION, STEERING
.............19-29
GEAR INPUT SHAFT SEAL - REMOVAL,
STEERING
..........................19-27
GEAR SELECTOR INDICATOR -
DESCRIPTION
.......................8J-27
GEAR SELECTOR INDICATOR -
OPERATION
.........................8J-27
GEAR SHIFT LEVER - INSTALLATION
.....19-12
GEAR SHIFT LEVER - REMOVAL
.........19-12
GEAR, SPECIAL TOOLS - POWER
STEERING
..........................19-23
GEAR, SPECIFICATIONS - POWER
STEERING
..........................19-22
GEAR TO COOLER - INSTALLATION,
RETURN HOSE
.................19-44,19-45
GEAR TO COOLER - REMOVAL, RETURN
HOSE
.........................19-44,19-45
GEAR/RING GEAR - INSTALLATION,
PINION
.........................3-51,3-77
GEAR/RING GEAR - REMOVAL, PINION
....3-49,
3-75
14 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

HEATED SEAT MODULE - INSTALLATION . . . 8E-7
HEATED SEAT MODULE - INSTALLATION . . 8G-15
HEATED SEAT MODULE - OPERATION.....8E-6
HEATED SEAT MODULE - OPERATION....8G-14
HEATED SEAT MODULE - REMOVAL.......8E-7
HEATED SEAT MODULE - REMOVAL.....8G-15
HEATED SEAT SENSOR - DESCRIPTION . . . 8G-11
HEATED SEAT SENSOR - DIAGNOSIS
AND TESTING.......................8G-11
HEATED SEAT SENSOR - OPERATION....8G-11
HEATED SEAT SENSOR - REMOVAL......8G-11
HEATED SEAT SWITCH - DESCRIPTION . . . 8G-11
HEATED SEAT SWITCH - DIAGNOSIS
AND TESTING.......................8G-12
HEATED SEAT SWITCH - INSTALLATION . . 8G-13
HEATED SEAT SWITCH - OPERATION.....8G-12
HEATED SEAT SWITCH - REMOVAL......8G-13
HEATED SEAT SYSTEM - DESCRIPTION....8G-7
HEATED SEAT SYSTEM - DIAGNOSIS
AND TESTING........................8G-8
HEATED SEAT SYSTEM - OPERATION.....8G-8
HEATER - 5.9L DIESEL - DESCRIPTION,
ENGINE BLOCK.......................7-37
HEATER - 5.9L DIESEL - INSTALLATION,
ENGINE BLOCK.......................7-38
HEATER - 5.9L DIESEL - OPERATION,
ENGINE BLOCK.......................7-38
HEATER - 5.9L DIESEL - REMOVAL,
ENGINE BLOCK.........................7-38
HEATER - DESCRIPTION, ENGINE BLOCK . . . 7-36
HEATER - DESCRIPTION, FUEL..........14-51
HEATER - DESCRIPTION, INTAKE AIR.....14-80
HEATER - DIAGNOSIS AND TESTING,
ENGINE BLOCK.......................7-36
HEATER - DIAGNOSIS AND TESTING,
FUEL..............................14-52
HEATER - INSTALLATION, ENGINE
BLOCK..............................7-37
HEATER - INSTALLATION, INTAKE AIR....14-80
HEATER - OPERATION, ENGINE BLOCK....7-36
HEATER - OPERATION, FUEL............14-51
HEATER - OPERATION, INTAKE AIR......14-80
HEATER - REMOVAL, ENGINE BLOCK......7-37
HEATER - REMOVAL, INTAKE AIR........14-80
HEATER AND AIR CONDITIONER -
DESCRIPTION........................24-1
HEATER AND AIR CONDITIONER -
OPERATION..........................24-1
HEATER CONTROL - DESCRIPTION, A/C . . . 24-14
HEATER CONTROL - INSTALLATION, A/C . . 24-15
HEATER CONTROL - REMOVAL, A/C......24-15
HEATER CORE - DESCRIPTION..........24-63
HEATER CORE - INSTALLATION.........24-63
HEATER CORE - OPERATION............24-63
HEATER CORE - REMOVAL.............24-63
HEATER INLET HOSE - INSTALLATION....24-64
HEATER INLET HOSE - REMOVAL........24-64
HEATER PERFORMANCE TEST -
DIAGNOSIS AND TESTING..............24-6
HEATER RELAY - DESCRIPTION, FUEL....14-52
HEATER RELAY - DESCRIPTION, INTAKE
AIR ...............................14-82
HEATER RELAY - INSTALLATION, FUEL . . . 14-53
HEATER RELAY - INSTALLATION, INTAKE
AIR ...............................14-82
HEATER RELAY - OPERATION, FUEL......14-52
HEATER RELAY - OPERATION, INTAKE
AIR ...............................14-82
HEATER RELAY - REMOVAL, FUEL.......14-52
HEATER RELAY - REMOVAL, INTAKE AIR . . 14-82
HEATER RETURN HOSE - INSTALLATION . . 24-65
HEATER RETURN HOSE - REMOVAL......24-64
HEIGHT ADJUSTMENT - 4WD (LD) -
STANDARD PROCEDURE.................2-3
HEIGHT MEASUREMENT - 4WD (LD) -
STANDARD PROCEDURE.................2-3
HEMI ENGINE - INSTALLATION, 3.7L/4.7L
AND 5.7L......................24-59,24-73
HEMI ENGINE - REMOVAL, 3.7L/4.7L
AND 5.7L......................24-57,24-71
HIGH BEAM INDICATOR - DESCRIPTION
. . 8J-28
HIGH BEAM INDICATOR - OPERATION
....8J-28
HIGH MOUNTED STOP LAMP -
INSTALLATION, CENTER
...............8L-11
HIGH MOUNTED STOP LAMP -
REMOVAL, CENTER
...................8L-11
HIGH MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER
...............8L-11HIGH MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER...................8L-11
HIGH PRESSURE RELIEF VALVE -
DESCRIPTION.......................24-48
HIGH PRESSURE RELIEF VALVE -
OPERATION.........................24-48
HIGH SPEEDS - DESCRIPTION, TIRE
PRESSURE..........................22-7
HIGH/LOW RELAY - DESCRIPTION,
WIPER.............................8R-20
HIGH/LOW RELAY - DIAGNOSIS AND
TESTING, WIPER.....................8R-21
HIGH/LOW RELAY - INSTALLATION,
WIPER.............................8R-22
HIGH/LOW RELAY - OPERATION, WIPER . . 8R-20
HIGH/LOW RELAY - REMOVAL, WIPER . . . 8R-21
HIGH-PRESSURE FUEL LINE LEAKS -
DIAGNOSIS AND TESTING.............14-58
HINGE - INSTALLATION.....23-16,23-22,23-31,
23-46
HINGE - INSTALLATION, CENTER SEAT
BACK..............................23-79
HINGE - REMOVAL....23-16,23-22,23-31,23-46
HINGE - REMOVAL, CENTER SEAT BACK . . 23-78
HINGE COVER - INSTALLATION, CENTER
SEAT BACK INERTIA..................23-77
HINGE COVER - REMOVAL, CENTER
SEAT BACK INERTIA..................23-77
HITCH - INSTALLATION, TRAILER........13-25
HITCH - REMOVAL, TRAILER...........13-25
HOAT COOLANT - DESCRIPTION..........7-32
HOISTING - STANDARD PROCEDURE......0-20
HOLDDOWN - DESCRIPTION, BATTERY . . . 8F-14
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-14
HOLDDOWN - OPERATION, BATTERY.....8F-14
HOLDDOWN - REMOVAL, BATTERY......8F-14
HOLDER - INSTALLATION, CUP.........23-51
HOLDER - REMOVAL, CUP.............23-51
HOLDING CLUTCHES - DESCRIPTION....21-371
HOLDING CLUTCHES - OPERATION.....21-372
HOLE PLUG - INSTALLATION, CAMSHAFT
CORE..............................9-206
HOLE PLUG - REMOVAL, CAMSHAFT
CORE..............................9-205
HOLE REPAIR - DESCRIPTION,
THREADED........................Intro.-8
HONING - STANDARD PROCEDURE,
CYLINDER BORE.................9-128,9-38
HOOD - INSTALLATION................23-47
HOOD - REMOVAL....................23-46
HOOK - INSTALLATION, COAT...........23-66
HOOK - REMOVAL, COAT..............23-66
HOOK ASSEMBLY - INSTALLATION,
FRONT TOW........................13-23
HOOK ASSEMBLY - REMOVAL, FRONT
TOW ..............................13-23
HORN - DIAGNOSIS AND TESTING.......8H-1
HORN - INSTALLATION.................8H-2
HORN - REMOVAL....................8H-2
HORN SWITCH - DESCRIPTION..........8H-2
HORN SWITCH - DIAGNOSIS AND
TESTING............................8H-2
HORN SYSTEM - DESCRIPTION..........8H-1
HORN SYSTEM - DIAGNOSIS AND
TESTING............................8H-1
HORN SYSTEM - OPERATION............8H-1
HOSE - GEAR TO COOLER -
INSTALLATION, RETURN..........19-44,19-45
HOSE - GEAR TO COOLER - REMOVAL,
RETURN......................19-44,19-45
HOSE - INSTALLATION, FRONT BRAKE.....5-13
HOSE - INSTALLATION, HEATER INLET....24-64
HOSE - INSTALLATION, HEATER RETURN . 24-65
HOSE - INSTALLATION, PRESSURE . 19-44,19-45
HOSE - INSTALLATION, REAR BRAKE......5-12
HOSE - REMOVAL, FRONT..............5-12
HOSE - REMOVAL, HEATER INLET.......24-64
HOSE - REMOVAL, HEATER RETURN.....24-64
HOSE - REMOVAL, PRESSURE.....19-44,19-45
HOSE - REMOVAL, REAR BRAKE
.........5-11
HOSE - RESERVOIR TO COOLER -
INSTALLATION, RETURN
..........19-44,19-45
HOSE - RESERVOIR TO COOLER -
REMOVAL, RETURN
.............19-44,19-45
HOSE ASSEMBLY - INSTALLATION, REAR
TUBE
...............................5-13
HOSE ASSEMBLY - REMOVAL, REAR
TUBE
...............................5-12HOSE CLAMPS - DESCRIPTION...........7-3
HOSE CLAMPS - OPERATION.............7-5
HOSES/TUBES - DESCRIPTION, WASHER . 8R-11
HOSES/TUBES - OPERATION, WASHER . . . 8R-11
HOUSING - ASSEMBLY, HVAC...........24-35
HOUSING - DIAGNOSIS AND TESTING,
CLUTCH..............................6-7
HOUSING - DISASSEMBLY, HVAC........24-35
HOUSING - INSTALLATION, CLUTCH.......6-9
HOUSING - INSTALLATION, GEAR........9-300
HOUSING - INSTALLATION, HVAC........24-36
HOUSING - INSTALLATION, ROCKER.....9-255
HOUSING - REMOVAL, CLUTCH...........6-9
HOUSING - REMOVAL, GEAR...........9-299
HOUSING - REMOVAL, HVAC...........24-34
HOUSING - REMOVAL, ROCKER.........9-255
HOUSING BUSHING AND SEAL -
INSTALLATION, EXTENSION...........21-440
HOUSING BUSHING AND SEAL -
REMOVAL, EXTENSION...............21-440
HOUSING COVER - INSTALLATION, GEAR . 9-301
HOUSING COVER - REMOVAL, GEAR.....9-301
HOUSING FLUID LEAK - DIAGNOSIS AND
TESTING, CONVERTER.........21-144,21-318
HOUSING SEAL - INSTALLATION,
ADAPTER...............21-128,21-364,21-85
HOUSING SEAL - INSTALLATION,
EXTENSION . 21-128,21-201,21-507,21-536,21-85
HOUSING SEAL - REMOVAL, ADAPTER . . 21-128,
21-364,21-85
HOUSING SEAL - REMOVAL,
EXTENSION . 21-128,21-201,21-507,21-536,21-85
HOUSING SEAL AND DUST BOOT -
INSTALLATION, EXTENSION.....21-476,21-571
HOUSING SEAL AND DUST BOOT -
REMOVAL, EXTENSION.........21-476,21-571
HOW TO USE WIRING DIAGRAMS -
DESCRIPTION.....................8W-01-1
H-SECTION REPLACEMENT - STANDARD
PROCEDURE, REAR FRAME............13-13
HUB / BEARING - INSTALLATION.........2-32
HUB / BEARING - REMOVAL.............2-31
HVAC HOUSING - ASSEMBLY...........24-35
HVAC HOUSING - DISASSEMBLY........24-35
HVAC HOUSING - INSTALLATION........24-36
HVAC HOUSING - REMOVAL............24-34
HYDRAULIC BOOSTER - DIAGNOSIS
AND TESTING........................5-30
HYDRAULIC LASH ADJUSTER -
DIAGNOSIS AND TESTING.........9-125,9-32
HYDRAULIC PRESSURE TEST -
DIAGNOSIS AND TESTING......21-141,21-316
HYDRAULIC SCHEMATICS, SCHEMATICS
AND DIAGRAMS..............21-176,21-337
HYDRAULIC TAPPETS - DIAGNOSIS AND
TESTING...........................9-210
HYDRAULIC TAPPETS - INSTALLATION . . . 9-211
HYDRAULIC TAPPETS - REMOVAL.......9-211
HYDROBOOST - INSTALLATION..........5-27
HYDROBOOST - INSTALLATION, ALL
EXCEPT.............................5-27
HYDROBOOST - REMOVAL..............5-26
HYDROBOOST - REMOVAL, ALL EXCEPT . . . 5-26
HYDRO-BOOST BRAKE BOOSTER -
INSTALLATION........................5-32
HYDRO-BOOST BRAKE BOOSTER -
REMOVAL
...........................5-31
HYDROFORM FENDER RAIL REPAIR -
STANDARD PROCEDURE
...............13-11
HYDROSTATIC LOCK - STANDARD
PROCEDURE
...................9-190,9-240
IDENTIFICATION - DESCRIPTION,
FASTENER
.........................Intro.-5
IDENTIFICATION AND INFORMATION -
DESCRIPTION, SECTION
.............8W-01-6
IDENTIFICATION NUMBER -
DESCRIPTION, VEHICLE
..............Intro.-1
IDLE AIR CONTROL MOTOR -
DESCRIPTION
.......................14-28
IDLE AIR CONTROL MOTOR -
INSTALLATION
.......................14-29
IDLE AIR CONTROL MOTOR -
OPERATION
.........................14-28
IDLE AIR CONTROL MOTOR - REMOVAL
. . 14-29
IDLER SHAFT - INSTALLATION
......9-179,9-81
IDLER SHAFT - REMOVAL
..........9-179,9-81
IGNITION - SPECIFICATIONS, TORQUE
.....8I-3
16 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

IGNITION CIRCUIT SENSE -
DESCRIPTION.......................8E-10
IGNITION CIRCUIT SENSE - OPERATION . . 8E-11
IGNITION COIL - DESCRIPTION..........8I-11
IGNITION COIL - INSTALLATION.........8I-14
IGNITION COIL - OPERATION............8I-12
IGNITION COIL - REMOVAL.............8I-13
IGNITION COIL CAPACITOR -
DESCRIPTION........................8I-21
IGNITION COIL CAPACITOR -
INSTALLATION.......................8I-21
IGNITION COIL CAPACITOR - OPERATION . . 8I-21
IGNITION COIL CAPACITOR - REMOVAL . . . 8I-21
IGNITION COIL RESISTANCE, 3.7L V-6.....8I-5
IGNITION COIL RESISTANCE, 4.7L V-8.....8I-5
IGNITION COIL RESISTANCE, 5.7L V-8.....8I-5
IGNITION CONTROL - DESCRIPTION.......8I-1
IGNITION SWITCH - DESCRIPTION........19-9
IGNITION SWITCH - DESCRIPTION,
KEY-IN.............................19-11
IGNITION SWITCH - DIAGNOSIS AND
TESTING............................19-9
IGNITION SWITCH - INSTALLATION......19-11
IGNITION SWITCH - OPERATION.........19-9
IGNITION SWITCH - REMOVAL..........19-10
IGNITION SWITCH AND KEY LOCK
CYLINDER - DIAGNOSIS AND TESTING . . . 19-11
IGNITION TIMING, SPECIFICATIONS.......8I-5
IGNITION-OFF DRAW TEST - STANDARD
PROCEDURE........................8F-11
IMMOBILIZER MODULE - DESCRIPTION,
SENTRY KEY........................8E-13
IMMOBILIZER MODULE - INSTALLATION,
SENTRY KEY........................8E-15
IMMOBILIZER MODULE - OPERATION,
SENTRY KEY........................8E-13
IMMOBILIZER MODULE - REMOVAL,
SENTRY KEY........................8E-15
IMMOBILIZER MODULE (SKIM) -
DESCRIPTION, SENTRY KEY.............8Q-1
IMMOBILIZER MODULE (SKIM) -
OPERATION, SENTRY KEY..............8Q-2
IMMOBILIZER SYSTEM INDICATOR
LAMP - DESCRIPTION, SENTRY KEY......8Q-5
IMMOBILIZER SYSTEM INDICATOR
LAMP - OPERATION, SENTRY KEY........8Q-5
IMMOBILIZER SYSTEM INITIALIZATION,
STANDARD PROCEDURE - SENTRY
KEY................................8Q-3
IMMOBILIZER SYSTEM (SKIS) -
DESCRIPTION, SENTRY KEY.............8Q-1
IMMOBILIZER SYSTEM (SKIS) -
OPERATION, SENTRY KEY..............8Q-2
IMMOBILIZER SYSTEM TRANSPONDER
PROGRAMMING, STANDARD
PROCEDURE - SENTRY KEY.............8Q-4
IMPACT SENSOR - DESCRIPTION, SIDE . . 8O-59
IMPACT SENSOR - OPERATION, SIDE....8O-59
INCORRECT FLUID LEVEL - DIAGNOSIS
AND TESTING, EFFECTS OF......21-201,21-366
INDEPENDENT FRONT SUSPENSION -
DESCRIPTION, GEAR..................19-17
INDEPENDENT FRONT SUSPENSION -
INSTALLATION, GEAR.................19-18
INDEPENDENT FRONT SUSPENSION -
REMOVAL, GEAR.....................19-17
INDICATOR - DESCRIPTION, ABS........8J-17
INDICATOR - DESCRIPTION, AIRBAG.....8J-18
INDICATOR - DESCRIPTION, BRAKE/
PARK BRAKE........................8J-19
INDICATOR - DESCRIPTION, CARGO
LAMP
..............................8J-20
INDICATOR - DESCRIPTION, CHECK
GAUGES
............................8J-21
INDICATOR - DESCRIPTION, CRUISE
.....8J-22
INDICATOR - DESCRIPTION, DOOR AJAR
. . 8J-23
INDICATOR - DESCRIPTION, ETC
........8J-25
INDICATOR - DESCRIPTION, GEAR
SELECTOR
..........................8J-27
INDICATOR - DESCRIPTION, HIGH BEAM
. . 8J-28
INDICATOR - DESCRIPTION, LAMP OUT
. . . 8J-29
INDICATOR - DESCRIPTION, LOW FUEL
. . . 8J-30
INDICATOR - DESCRIPTION, SEATBELT
. . . 8J-34
INDICATOR - DESCRIPTION, SECURITY
. . . 8J-35
INDICATOR - DESCRIPTION, SERVICE
4WD
...............................8J-36
INDICATOR - DESCRIPTION, TOW/HAUL
. . . 8J-39INDICATOR - DESCRIPTION, TRANS
TEMP..............................8J-40
INDICATOR - DESCRIPTION, TURN
SIGNAL............................8J-40
INDICATOR - DESCRIPTION, UPSHIFT....8J-41
INDICATOR - DESCRIPTION, WAIT-TO-
START .............................8J-44
INDICATOR - DESCRIPTION, WASHER
FLUID..............................8J-44
INDICATOR - DESCRIPTION, WATER-IN-
FUEL..............................8J-45
INDICATOR - DIAGNOSIS AND TESTING,
BRAKE.............................8J-20
INDICATOR - OPERATION, ABS..........8J-17
INDICATOR - OPERATION, AIRBAG.......8J-18
INDICATOR - OPERATION, BRAKE/PARK
BRAKE.............................8J-19
INDICATOR - OPERATION, CARGO LAMP . . 8J-20
INDICATOR - OPERATION, CHECK
GAUGES............................8J-21
INDICATOR - OPERATION, CRUISE.......8J-22
INDICATOR - OPERATION, DOOR AJAR . . . 8J-23
INDICATOR - OPERATION, ETC..........8J-25
INDICATOR - OPERATION, GEAR
SELECTOR..........................8J-27
INDICATOR - OPERATION, HIGH BEAM....8J-28
INDICATOR - OPERATION, LAMP OUT....8J-29
INDICATOR - OPERATION, LOW FUEL.....8J-30
INDICATOR - OPERATION, SEATBELT.....8J-34
INDICATOR - OPERATION, SECURITY......8J-36
INDICATOR - OPERATION, SERVICE 4WD . . 8J-37
INDICATOR - OPERATION, TOW/HAUL....8J-39
INDICATOR - OPERATION, TRANS TEMP . . 8J-40
INDICATOR - OPERATION, TURN SIGNAL . . 8J-41
INDICATOR - OPERATION, UPSHIFT......8J-42
INDICATOR - OPERATION, WAIT-TO-
START .............................8J-44
INDICATOR - OPERATION, WASHER
FLUID..............................8J-44
INDICATOR - OPERATION, WATER-IN-
FUEL..............................8J-45
INDICATOR LAMP - DESCRIPTION,
SENTRY KEY IMMOBILIZER SYSTEM......8Q-5
INDICATOR LAMP - OPERATION,
SENTRY KEY IMMOBILIZER SYSTEM......8Q-5
INDICATOR LAMP (MIL) - DESCRIPTION,
MALFUNCTION.......................8J-31
INDICATOR LAMP (MIL) - OPERATION,
MALFUNCTION.......................8J-31
INDICATOR TEST - STANDARD
PROCEDURE, BUILT-IN................8F-10
INDICATORS - DIAGNOSIS AND
TESTING, TREAD WEAR................22-8
INERTIA HINGE COVER - INSTALLATION,
CENTER SEAT BACK..................23-77
INERTIA HINGE COVER - REMOVAL,
CENTER SEAT BACK..................23-77
INFLATION PRESSURES - DESCRIPTION,
TIRE................................22-7
INFO CENTER - DESCRIPTION,
ELECTRONIC VEHICLE.................8M-7
INFO CENTER - INSTALLATION,
ELECTRONIC VEHICLE.................8M-9
INFO CENTER - OPERATION,
ELECTRONIC VEHICLE.................8M-7
INFO CENTER - REMOVAL, ELECTRONIC
VEHICLE............................8M-9
INITIAL OPERATION - STANDARD
PROCEDURE, POWER STEERING
PUMP.............................19-40
INITIALIZATION, STANDARD PROCEDURE
- SENTRY KEY IMMOBILIZER SYSTEM....8Q-3
INJECTED RINGS - ASSEMBLY, WITH......3-13
INJECTED RINGS - DISASSEMBLY, WITH . . . 3-11
INJECTION PUMP - DESCRIPTION, FUEL . . 14-53
INJECTION PUMP - INSTALLATION, FUEL . 14-55
INJECTION PUMP - OPERATION, FUEL....14-53
INJECTION PUMP - REMOVAL, FUEL.....14-54
INJECTION PUMP TIMING - DIAGNOSIS
AND TESTING, FUEL..................14-53
INJECTOR - DESCRIPTION, FUEL . . . 14-26,14-74
INJECTOR - INSTALLATION, FUEL........14-77
INJECTOR - OPERATION, FUEL
.....14-26,14-74
INJECTOR - REMOVAL, FUEL
...........14-75
INJECTOR FIRING ORDER, DIESEL -
FUEL
..............................14-48
INJECTOR RAIL - DESCRIPTION, FUEL
....14-78
INJECTOR RAIL - INSTALLATION, FUEL
. . . 14-78INJECTOR RAIL - OPERATION, FUEL.....14-78
INJECTOR RAIL - REMOVAL, FUEL.......14-78
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - DESCRIPTION.....14-79
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - INSTALLATION.....14-79
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - OPERATION.......14-79
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - REMOVAL........14-79
INLET FILTER - INSTALLATION..........14-20
INLET FILTER - REMOVAL..............14-20
INLET HOSE - INSTALLATION, HEATER....24-64
INLET HOSE - REMOVAL, HEATER.......24-64
INNER BELT MOLDING - INSTALLATION,
FRONT DOOR.......................23-93
INNER BELT MOLDING - INSTALLATION,
REAR DOOR........................23-94
INNER BELT MOLDING - REMOVAL,
FRONT DOOR.......................23-93
INNER BELT MOLDING - REMOVAL,
REAR DOOR........................23-94
INPUT - OPERATION, ASD SENSE - PCM . . . 8I-5
INPUT CLUTCH ASSEMBLY - ASSEMBLY . 21-378
INPUT CLUTCH ASSEMBLY -
DESCRIPTION......................21-373
INPUT CLUTCH ASSEMBLY -
DISASSEMBLY......................21-374
INPUT CLUTCH ASSEMBLY - OPERATION . 21-373
INPUT SHAFT SEAL - INSTALLATION,
STEERING GEAR.......................19-29
INPUT SHAFT SEAL - REMOVAL,
STEERING GEAR.....................19-27
INPUT SPEED SENSOR - DESCRIPTION . . 21-382
INPUT SPEED SENSOR - INSTALLATION . 21-382
INPUT SPEED SENSOR - OPERATION....21-382
INPUT SPEED SENSOR - REMOVAL.....21-382
INSERTS - INSTALLATION, SPRING TIP....2-45
INSERTS - REMOVAL, SPRING TIP........2-44
INSIDE HANDLE ACTUATOR -
INSTALLATION..................23-22,23-32
INSIDE HANDLE ACTUATOR - REMOVAL . . 23-22,
23-31
INSTRUMENT CLUSTER - ASSEMBLY.....8J-15
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-2
INSTRUMENT CLUSTER - DIAGNOSIS
AND TESTING.......................8J-10
INSTRUMENT CLUSTER - DISASSEMBLY . . 8J-14
INSTRUMENT CLUSTER - INSTALLATION . . 8J-16
INSTRUMENT CLUSTER - OPERATION.....8J-6
INSTRUMENT CLUSTER - REMOVAL.....8J-14
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-7
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-7
INSTRUMENT PANEL ASSEMBLY -
INSTALLATION.......................23-55
INSTRUMENT PANEL ASSEMBLY -
REMOVAL..........................23-52
INSTRUMENT PANEL CENTER BEZEL -
INSTALLATION.......................23-57
INSTRUMENT PANEL CENTER BEZEL -
REMOVAL..........................23-57
INSTRUMENT PANEL DEMISTER DUCTS
- INSTALLATION.....................24-37
INSTRUMENT PANEL DEMISTER DUCTS
- REMOVAL.........................24-36
INSTRUMENT PANEL DRIVER SIDE
BEZEL - INSTALLATION................23-58
INSTRUMENT PANEL DRIVER SIDE
BEZEL - REMOVAL...................23-58
INSTRUMENT PANEL DUCTS -
INSTALLATION.......................24-37
INSTRUMENT PANEL DUCTS - REMOVAL . 24-37
INSTRUMENT PANEL HEADLAMP
SWITCH BEZEL - INSTALLATION.........23-56
INSTRUMENT PANEL HEADLAMP
SWITCH BEZEL - REMOVAL............23-56
INSTRUMENT PANEL LOWER
SURROUND - INSTALLATION...........23-59
INSTRUMENT PANEL LOWER
SURROUND - REMOVAL
...............23-59
INSTRUMENT PANEL TOP COVER -
INSTALLATION
.......................23-59
INSTRUMENT PANEL TOP COVER -
REMOVAL
..........................23-58
INTAKE AIR HEATER - DESCRIPTION
.....14-80
INTAKE AIR HEATER - INSTALLATION
.....14-80
DRINDEX 17
Description Group-Page Description Group-Page Description Group-Page

LATCH STRIKER - INSTALLATION . . 23-17,23-23,
23-33
LATCH STRIKER - REMOVAL . 23-16,23-23,23-33
LATCH STRIKER / SECONDARY CATCH -
INSTALLATION.......................23-48
LATCH STRIKER / SECONDARY CATCH -
REMOVAL..........................23-47
LD & HD EXCEPT 4X4 HD -
INSTALLATION, ALL..................19-14
LD & HD EXCEPT 4X4 HD - REMOVAL,
ALL ...............................19-14
LD FRONT - INSTALLATION, PROPELLER
SHAFT...............................3-7
LD FRONT - REMOVAL, PROPELLER
SHAFT...............................3-6
LEAD - DIAGNOSIS AND TESTING,
TIRE/VEHICLE........................22-8
LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING FLUID....21-144,21-318
LEAK - DIAGNOSIS AND TESTING,
ENGINE OIL................9-152,9-220,9-64
LEAK DETECTION ASSY - DESCRIPTION,
NATURAL VAC.......................25-23
LEAK DETECTION ASSY - INSTALLATION,
NATURAL VAC.......................25-25
LEAK DETECTION ASSY - OPERATION,
NATURAL VAC.......................25-23
LEAK DETECTION ASSY - REMOVAL,
NATURAL VAC.......................25-24
LEAK DETECTION PUMP - DESCRIPTION . . 25-13
LEAK DETECTION PUMP - INSTALLATION . 25-16
LEAK DETECTION PUMP - OPERATION....25-14
LEAK DETECTION PUMP - REMOVAL.....25-16
LEAKAGE - DIAGNOSIS AND TESTING,
CYLINDER COMBUSTION PRESSURE . 9-186,9-8,
9-93
LEAKAGE - DIAGNOSIS AND TESTING,
INTAKE MANIFOLD..............9-159,9-225
LEAKAGE - DIAGNOSIS AND TESTING,
PUMP.............................19-40
LEAKS - DIAGNOSIS AND TESTING,
CHARGE AIR COOLER SYSTEM.........11-16
LEAKS - DIAGNOSIS AND TESTING,
COOLING SYSTEM - TESTING.............7-5
LEAKS - DIAGNOSIS AND TESTING,
HIGH-PRESSURE FUEL LINE............14-58
LEAKS - DIAGNOSIS AND TESTING,
INTAKE MANIFOLD....................9-72
LEAKS - DIAGNOSIS AND TESTING,
REAR SEAL AREA...........9-137,9-209,9-65
LEAKS - DIAGNOSIS AND TESTING,
REFRIGERANT SYSTEM...............24-44
LEAKS - DIAGNOSIS AND TESTING,
WATER .............................23-1
LEAKS - STANDARD PROCEDURE,
REPAIRING.........................22-10
LEARN - STANDARD PROCEDURE,
DRIVE.............................8E-23
LEARN - STANDARD PROCEDURE, TCM
QUICK.............................8E-23
LEFT CYLINDER HEAD - INSTALLATION . . . 9-112
LEFT CYLINDER HEAD - REMOVAL.......9-108
LEFT REAR CABLE - INSTALLATION.......5-39
LEFT REAR CABLE - REMOVAL...........5-38
LENS REPLACEMENT - STANDARD
PROCEDURE, MODULE................8M-3
LEVEL - DIAGNOSIS AND TESTING,
EFFECTS OF INCORRECT FLUID . . 21-201,21-366
LEVEL - STANDARD PROCEDURE,
BRAKE FLUID........................5-23
LEVEL - STANDARD PROCEDURE,
ENGINE OIL.........................9-292
LEVEL - STANDARD PROCEDURE,
REFRIGERANT OIL...................24-69
LEVEL CHECK - STANDARD
PROCEDURE, COOLANT................7-17
LEVEL CHECK - STANDARD
PROCEDURE, FLUID...........21-202,21-366
LEVEL CHECKING - STANDARD
PROCEDURE, POWER STEERING FLUID
. . . 19-43
LEVEL SENDING UNIT / SENSOR -
DESCRIPTION, FUEL
..............14-57,14-6
LEVEL SENDING UNIT / SENSOR -
INSTALLATION, FUEL
..................14-7
LEVEL SENDING UNIT / SENSOR -
OPERATION, FUEL
................14-57,14-6
LEVEL SENDING UNIT / SENSOR -
REMOVAL, FUEL
......................14-7LEVEL SWITCH - DESCRIPTION,
WASHER FLUID......................8R-9
LEVEL SWITCH - INSTALLATION,
WASHER FLUID.....................8R-11
LEVEL SWITCH - OPERATION, WASHER
FLUID..............................8R-9
LEVEL SWITCH - REMOVAL, WASHER
FLUID.............................8R-10
LEVER - ADJUSTMENT, SHIFT . . . 21-446,21-481
LEVER - INSTALLATION, GEAR SHIFT.....19-12
LEVER - INSTALLATION, SHIFT . . . 21-445,21-480
LEVER - REMOVAL, GEAR SHIFT........19-12
LEVER - REMOVAL, SHIFT......21-444,21-479
LEVER KNOB RELEASE - INSTALLATION,
TILT ...............................19-16
LEVER KNOB RELEASE - REMOVAL, TILT . . 19-16
LICENSE PLATE LAMP - INSTALLATION . . . 8L-17
LICENSE PLATE LAMP - REMOVAL.......8L-17
LICENSE PLATE LAMP UNIT -
INSTALLATION.......................8L-17
LICENSE PLATE LAMP UNIT - REMOVAL . . 8L-17
LID - INSTALLATION, CENTER SEAT
BACK..............................23-79
LID - INSTALLATION, UNDER SEAT
STORAGE BIN.......................23-80
LID - REMOVAL, CENTER SEAT BACK....23-79
LID - REMOVAL, UNDER SEAT STORAGE
BIN ...............................23-80
LIFTERS/TAPPETS - CLEANING, SOLID....9-279
LIFTERS/TAPPETS - INSPECTION, SOLID . . . 9-279
LIFTERS/TAPPETS - INSTALLATION,
SOLID.............................9-280
LIFTERS/TAPPETS - REMOVAL, SOLID....9-279
LIGHT DUTY FRONT FRAME RAIL TIP
REPLACEMENT - STANDARD
PROCEDURE.........................13-4
LIGHTER OUTLET - DESCRIPTION,
CIGAR...........................8W-97-2
LIGHTER OUTLET - DIAGNOSIS AND
TESTING, CIGAR...................8W-97-2
LIGHTER OUTLET - OPERATION, CIGAR . 8W-97-2
LIMITING VALVE - DESCRIPTION, FUEL
PRESSURE.........................14-61
LIMITING VALVE - INSTALLATION, FUEL
PRESSURE.........................14-61
LIMITING VALVE - OPERATION, FUEL
PRESSURE.........................14-61
LIMITING VALVE - REMOVAL, FUEL
PRESSURE.........................14-61
LINE - DESCRIPTION, A/C DISCHARGE....24-56
LINE - DESCRIPTION, LIQUID...........24-65
LINE - DESCRIPTION, REFRIGERANT.....24-42
LINE - DESCRIPTION, SUCTION.........24-70
LINE - INSTALLATION, LIQUID..........24-66
LINE - REMOVAL, LIQUID..............24-65
LINE AND TERMINAL REPAIR -
STANDARD PROCEDURE, GRID..........8G-4
LINE COUPLER - DESCRIPTION,
REFRIGERANT.......................24-67
LINE COUPLER - INSTALLATION,
REFRIGERANT.......................24-68
LINE COUPLER - OPERATION,
REFRIGERANT.......................24-67
LINE COUPLER - REMOVAL,
REFRIGERANT.......................24-68
LINE LEAKS - DIAGNOSIS AND TESTING,
HIGH-PRESSURE FUEL................14-58
LINE PRESSURE (LP) SENSOR -
DESCRIPTION......................21-382
LINE PRESSURE (LP) SENSOR -
INSTALLATION......................21-383
LINE PRESSURE (LP) SENSOR -
OPERATION........................21-383
LINE PRESSURE (LP) SENSOR -
REMOVAL.........................21-383
LINES - DESCRIPTION, FUEL.......14-57,14-7
LINES - DESCRIPTION, VACUUM........25-22
LINES - INSTALLATION, FUEL...........14-60
LINES - OPERATION, FUEL.............14-57
LINES - OPERATION, REFRIGERANT......24-42
LINES - REMOVAL, FUEL..............14-58
LINK - INSTALLATION, DRAG...........19-36
LINK - REMOVAL, DRAG...............19-36
LINK CONNECTOR - DESCRIPTION, DATA
. . 8E-3
LINK CONNECTOR - OPERATION, DATA
....8E-3
LINKAGE - INSTALLATION
...............6-12
LINKAGE - LINK/COIL - DESCRIPTION
....19-34
LINKAGE - REMOVAL
..................6-12LINKAGE, SPECIAL TOOLS - STEERING . . . 19-35
LINK/COIL - DESCRIPTION, GEAR........19-20
LINK/COIL - DESCRIPTION, LINKAGE.....19-34
LINK/COIL - INSTALLATION, GEAR.......19-21
LINK/COIL - OPERATION, GEAR.........19-20
LINK/COIL - REMOVAL, GEAR...........19-20
LINK/COIL SUSPENSION - STANDARD
PROCEDURE, ALIGNMENT...............2-5
LIQUID LINE - DESCRIPTION...........24-65
LIQUID LINE - INSTALLATION...........24-66
LIQUID LINE - REMOVAL..............24-65
LOAD FLOOR - INSTALLATION..........23-72
LOAD FLOOR - REMOVAL..............23-71
LOAD FLOOR SUPPORT CYLINDER -
INSTALLATION.......................23-72
LOAD FLOOR SUPPORT CYLINDER -
REMOVAL..........................23-72
LOCATION - DESCRIPTION, CONNECTOR/
GROUND/SPLICE...................8W-91-1
LOCATIONS - SPECIFICATIONS, SEALER . 23-102
LOCATIONS - SPECIFICATIONS,
STRUCTURAL ADHESIVE..............23-112
LOCATIONS - SPECIFICATIONS, WELD . . . 23-120
LOCK - STANDARD PROCEDURE,
HYDROSTATIC..................9-190,9-240
LOCK CYLINDER - DIAGNOSIS AND
TESTING, IGNITION SWITCH AND KEY....19-11
LOCK CYLINDER - INSTALLATION.......23-24
LOCK CYLINDER - REMOVAL.............23-24
LOCK MOTOR - DESCRIPTION, DOOR.....8N-4
LOCK MOTOR - DIAGNOSIS AND
TESTING, DOOR......................8N-4
LOCK MOTOR - OPERATION, DOOR.......8N-4
LOCK SWITCH - DIAGNOSIS AND
TESTING, POWER.....................8N-4
LOCK SWITCH - INSTALLATION, POWER . . . 8N-4
LOCK SWITCH - REMOVAL, POWER......8N-4
LOCKING RETRACTOR - DESCRIPTION,
AUTOMATIC........................8O-14
LOCKING RETRACTOR - OPERATION,
AUTOMATIC........................8O-14
LOCKS - DESCRIPTION, POWER.........8N-1
LOCKS - DIAGNOSIS AND TESTING,
POWER.............................8N-3
LOCKS - OPERATION, POWER...........8N-2
LOOP ADJUSTER - INSTALLATION, SEAT
BELT TURNING......................8O-55
LOOP ADJUSTER - REMOVAL, SEAT
BELT TURNING......................8O-55
LOOP BRACKETS - INSTALLATION, SEAT
BACK REAR - FOOTMANS..............23-85
LOOP BRACKETS - REMOVAL, SEAT
BACK REAR - FOOTMANS..............23-85
LOW FUEL INDICATOR - DESCRIPTION . . . 8J-30
LOW FUEL INDICATOR - OPERATION.....8J-30
LOWER BALL JOINT - DIAGNOSIS AND
TESTING........................2-19,2-34
LOWER BALL JOINT - INSTALLATION . 2-20,2-35
LOWER BALL JOINT - REMOVAL.....2-19,2-35
LOWER CONTROL ARM BUSHINGS -
2WD (LD) - INSTALLATION..............2-15
LOWER CONTROL ARM BUSHINGS -
2WD (LD) - REMOVAL.................2-13
LOWER CONTROL ARM BUSHINGS -
4WD (LD) - INSTALLATION..............2-14
LOWER CONTROL ARM BUSHINGS -
4WD (LD) - REMOVAL.................2-13
LOWER SURROUND - INSTALLATION,
INSTRUMENT PANEL..................23-59
LOWER SURROUND - REMOVAL,
INSTRUMENT PANEL..................23-59
LOWER SUSPENSION ARM -
INSTALLATION........................2-38
LOWER SUSPENSION ARM - REMOVAL....2-38
LOWER TRIM - INSTALLATION,
B-PILLAR...........................23-64
LOWER TRIM - INSTALLATION,
C-PILLAR...........................23-67
LOWER TRIM - REMOVAL, B-PILLAR.....23-63
LOWER TRIM - REMOVAL, C-PILLAR.....23-66
LOW/REVERSE CLUTCH - ASSEMBLY....21-385
LOW/REVERSE CLUTCH - CLEANING
....21-385
LOW/REVERSE CLUTCH - DISASSEMBLY
. 21-384
LOW/REVERSE CLUTCH - INSPECTION
. . 21-385
LUBRICANTS - DESCRIPTION, ENGINE
OIL
.................................0-1
LUBRICATION - DESCRIPTION
.....9-150,9-220,
9-289,9-61
DRINDEX 19
Description Group-Page Description Group-Page Description Group-Page

PISTON RETAINER - ASSEMBLY,
OVERRUNNING CLUTCH CAM/
OVERDRIVE........................21-237
PISTON RETAINER - CLEANING,
OVERRUNNING CLUTCH CAM/
OVERDRIVE........................21-236
PISTON RETAINER - DESCRIPTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE........................21-236
PISTON RETAINER - DISASSEMBLY,
OVERRUNNING CLUTCH CAM/
OVERDRIVE........................21-236
PISTON RETAINER - INSPECTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE........................21-237
PISTON RETAINER - OPERATION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE........................21-236
PISTON RING FITTING - STANDARD
PROCEDURE..........9-142,9-213,9-284,9-53
PISTONS - DESCRIPTION.......21-239,21-393
PISTONS - INSPECTION...............9-282
PISTONS - OPERATION.........21-239,21-393
PITMAN ARM - INSTALLATION..........19-37
PITMAN ARM - REMOVAL.............19-36
PLANETARY GEARTRAIN - ASSEMBLY . . . 21-397
PLANETARY GEARTRAIN - CLEANING....21-396
PLANETARY GEARTRAIN - DESCRIPTION . 21-395
PLANETARY GEARTRAIN -
DISASSEMBLY......................21-396
PLANETARY GEARTRAIN - INSPECTION . . 21-397
PLANETARY GEARTRAIN - OPERATION . . 21-396
PLANETARY GEARTRAIN/OUTPUT SHAFT
- ASSEMBLY.......................21-244
PLANETARY GEARTRAIN/OUTPUT SHAFT
- DESCRIPTION.....................21-241
PLANETARY GEARTRAIN/OUTPUT SHAFT
- DISASSEMBLY....................21-242
PLANETARY GEARTRAIN/OUTPUT SHAFT
- INSPECTION......................21-243
PLANETARY GEARTRAIN/OUTPUT SHAFT
- OPERATION.......................21-241
PLASTIC BODY PANEL REPAIR -
STANDARD PROCEDURE................23-3
PLATE - DESCRIPTION, BODY CODE....Intro.-3
PLATE - DESCRIPTION, ENGINE DATA....9-248
PLATE - INSTALLATION, FLEX . . 9-138,9-210,9-48
PLATE - INSTALLATION, FRONT SKID.....13-23
PLATE - INSTALLATION, SUPPORT........5-36
PLATE - INSTALLATION, TRANSFER
CASE SKID.........................13-26
PLATE - REMOVAL, FLEX.....9-138,9-210,9-48
PLATE - REMOVAL, FRONT SKID........13-23
PLATE - REMOVAL, SUPPORT...........5-35
PLATE - REMOVAL, TRANSFER CASE
SKID..............................13-26
PLATE LAMP - INSTALLATION, LICENSE . . 8L-17
PLATE LAMP - REMOVAL, LICENSE......8L-17
PLATE LAMP UNIT - INSTALLATION,
LICENSE...........................8L-17
PLATE LAMP UNIT - REMOVAL, LICENSE . . 8L-17
PLATES - INSTALLATION, EXTERIOR
NAME.............................23-38
PLATES - REMOVAL, EXTERIOR NAME....23-38
PLUG - DESCRIPTION, SPARK...........8I-17
PLUG - INSTALLATION, CAMSHAFT
CORE HOLE.........................9-206
PLUG - REMOVAL, CAMSHAFT CORE
HOLE..............................9-205
PLUG - REMOVAL, SPARK
..............8I-19
PLUG CABLE - DESCRIPTION, SPARK
.....8I-21
PLUG CABLE - INSTALLATION, SPARK
....8I-22
PLUG CABLE - OPERATION, SPARK
.......8I-21
PLUG CABLE - REMOVAL, SPARK
........8I-22
PLUG CABLE RESISTANCE,
SPECIFICATIONS - SPARK
...............8I-4
PLUG CONDITIONS - DIAGNOSIS AND
TESTING, SPARK
.....................8I-17
PLUGS - INSTALLATION, CORE
..........9-131
PLUGS - REMOVAL, CORE
.............9-131
PLUGS, SPECIFICATIONS - SPARK
........8I-4
PLUMBING - CLEANING, CHARGE AIR
COOLER
............................11-17
PLUMBING - DESCRIPTION, CHARGE
AIR COOLER
........................11-16
PLUMBING - INSPECTION, CHARGE AIR
COOLER
............................11-17PLUMBING - INSTALLATION, CHARGE
AIR COOLER........................11-17
PLUMBING - OPERATION, CHARGE AIR
COOLER............................11-16
PLUMBING - REMOVAL, CHARGE AIR
COOLER............................11-17
PLY TIRES - DESCRIPTION, RADIAL.......22-6
POLISHING - DESCRIPTION, FINESSE
SANDING/BUFFING...................23-74
PORT VALVE CORE - DESCRIPTION,
SERVICE...........................24-70
PORT VALVE CORE - INSTALLATION,
SERVICE...........................24-70
PORT VALVE CORES - REMOVAL,
SERVICE...........................24-70
POSITION SENSOR - DESCRIPTION.....21-442,
21-477
POSITION SENSOR - DESCRIPTION,
ACCELERATOR PEDAL............14-22,14-68
POSITION SENSOR - DESCRIPTION,
CAMSHAFT.........................14-71
POSITION SENSOR - DESCRIPTION,
CAMSHAFT...........................8I-7
POSITION SENSOR - DESCRIPTION,
CRANKSHAFT..................14-23,14-72
POSITION SENSOR - DESCRIPTION,
THROTTLE..........................14-41
POSITION SENSOR - INSTALLATION....21-443,
21-478
POSITION SENSOR - INSTALLATION,
ACCELERATOR PEDAL............14-22,14-71
POSITION SENSOR - INSTALLATION,
CAMSHAFT.........................14-72
POSITION SENSOR - INSTALLATION,
CAMSHAFT..........................8I-10
POSITION SENSOR - INSTALLATION,
CRANKSHAFT..................14-25,14-73
POSITION SENSOR - INSTALLATION,
THROTTLE..........................14-43
POSITION SENSOR - OPERATION . 21-442,21-477
POSITION SENSOR - OPERATION,
ACCELERATOR PEDAL............14-22,14-68
POSITION SENSOR - OPERATION,
CAMSHAFT.........................14-71
POSITION SENSOR - OPERATION,
CAMSHAFT...........................8I-7
POSITION SENSOR - OPERATION,
CRANKSHAFT..................14-23,14-72
POSITION SENSOR - OPERATION,
THROTTLE..........................14-41
POSITION SENSOR - REMOVAL . . 21-443,21-478
POSITION SENSOR - REMOVAL,
ACCELERATOR PEDAL............14-22,14-68
POSITION SENSOR - REMOVAL,
CAMSHAFT.........................14-72
POSITION SENSOR - REMOVAL,
CAMSHAFT...........................8I-9
POSITION SENSOR - REMOVAL,
CRANKSHAFT..................14-24,14-73
POSITION SENSOR - REMOVAL,
THROTTLE..........................14-41
POSITION SWITCH - DESCRIPTION,
CLUTCH PEDAL.......................6-13
POSITION SWITCH - DIAGNOSIS AND
TESTING, CLUTCH PEDAL...............6-13
POSITION SWITCH - OPERATION,
CLUTCH PEDAL.......................6-13
POTENTIAL - STANDARD PROCEDURE,
TESTING OF VOLTAGE..............8W-01-9
POWER - INSTALLATION, WINDOW
REGULATOR...................23-26,23-34
POWER - REMOVAL, WINDOW
REGULATOR...................23-25,23-34
POWER BRAKE BOOSTER -
DESCRIPTION........................5-29
POWER BRAKE BOOSTER -
INSTALLATION........................5-29
POWER BRAKE BOOSTER - OPERATION . . . 5-29
POWER BRAKE BOOSTER - REMOVAL.....5-29
POWER DISTRIBUTION - DESCRIPTION . 8W-97-1
POWER DISTRIBUTION - OPERATION . . 8W-97-1
POWER DISTRIBUTION SYSTEMS,
SPECIAL TOOLS
...................8W-97-2
POWER GROUNDS - DESCRIPTION
......8E-10
POWER LOCK SWITCH - DIAGNOSIS
AND TESTING
........................8N-4
POWER LOCK SWITCH - INSTALLATION
. . . 8N-4
POWER LOCK SWITCH - REMOVAL
.......8N-4POWER LOCKS - DESCRIPTION..........8N-1
POWER LOCKS - DIAGNOSIS AND
TESTING............................8N-3
POWER LOCKS - OPERATION............8N-2
POWER MIRROR SWITCH - DIAGNOSIS
AND TESTING.......................8N-12
POWER MIRROR SWITCH - REMOVAL . . . 8N-12
POWER MIRRORS - DESCRIPTION......8N-10
POWER MIRRORS - DIAGNOSIS AND
TESTING...........................8N-10
POWER MIRRORS - OPERATION........8N-10
POWER MODULE - DESCRIPTION,
INTEGRATED......................8W-97-3
POWER MODULE - INSTALLATION,
INTEGRATED......................8W-97-4
POWER MODULE - OPERATION,
INTEGRATED......................8W-97-3
POWER MODULE - REMOVAL,
INTEGRATED......................8W-97-3
POWER OUTLET - DESCRIPTION......8W-97-7
POWER OUTLET - DIAGNOSIS AND
TESTING.........................8W-97-7
POWER OUTLET - INSTALLATION.....8W-97-8
POWER OUTLET - OPERATION........8W-97-7
POWER OUTLET - REMOVAL.........8W-97-8
POWER SEAT SYSTEM - DIAGNOSIS
AND TESTING.......................8N-13
POWER SEAT TRACK - DESCRIPTION....8N-16
POWER SEAT TRACK - DIAGNOSIS AND
TESTING...........................8N-17
POWER SEAT TRACK - INSTALLATION....8N-17
POWER SEAT TRACK - OPERATION......8N-16
POWER SEAT TRACK - REMOVAL.......8N-17
POWER SEATS - DESCRIPTION.........8N-13
POWER SEATS - OPERATION...........8N-13
POWER STEERING FLOW AND
PRESSURE - DIAGNOSIS AND
TESTING............................19-4
POWER STEERING FLUID -
DESCRIPTION.........................0-3
POWER STEERING FLUID LEVEL
CHECKING - STANDARD PROCEDURE....19-43
POWER STEERING GEAR, SPECIAL
TOOLS.............................19-23
POWER STEERING GEAR,
SPECIFICATIONS.....................19-22
POWER STEERING PRESSURE SWITCH -
DESCRIPTION.......................19-46
POWER STEERING PRESSURE SWITCH -
OPERATION.........................19-46
POWER STEERING PUMP - INITIAL
OPERATION - STANDARD PROCEDURE . . . 19-40
POWER STEERING SYSTEM -
DIAGNOSIS AND TESTING..............19-2
POWER STEERING SYSTEM -
STANDARD PROCEDURE, FLUSHING.....19-40
POWER WINDOWS - DESCRIPTION......8N-19
POWER WINDOWS - DIAGNOSIS AND
TESTING...........................8N-19
POWER WINDOWS - OPERATION........8N-19
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON FUSES . 8W-01-10
PRE-ALIGNMENT INSPECTION -
DIAGNOSIS AND TESTING...............2-2
PRESSURE - DIAGNOSIS AND TESTING,
CHECKING ENGINE OIL.......9-152,9-220,9-65
PRESSURE - DIAGNOSIS AND TESTING,
CYLINDER COMPRESSION......9-186,9-8,9-93
PRESSURE - DIAGNOSIS AND TESTING,
ENGINE OIL.........................9-289
PRESSURE - DIAGNOSIS AND TESTING,
POWER STEERING FLOW...............19-4
PRESSURE - DIAGNOSIS AND TESTING,
TURBOCHARGER BOOST...............11-11
PRESSURE BLEEDING - STANDARD
PROCEDURE..........................5-5
PRESSURE CAP - DESCRIPTION,
RADIATOR...........................7-57
PRESSURE CAP - OPERATION,
RADIATOR...........................7-58
PRESSURE FOR HIGH SPEEDS -
DESCRIPTION, TIRE
...................22-7
PRESSURE GAUGE - DESCRIPTION, OIL
. . 8J-33
PRESSURE GAUGE - OPERATION, OIL
....8J-33
PRESSURE GAUGES - DIAGNOSIS AND
TESTING
............................22-7
PRESSURE HOSE - INSTALLATION
. . 19-44,19-45
24 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

PRESSURE HOSE - REMOVAL.....19-44,19-45
PRESSURE LEAKAGE - DIAGNOSIS AND
TESTING, CYLINDER COMBUSTION . . . 9-186,9-8,
9-93
PRESSURE LIMITING VALVE -
DESCRIPTION, FUEL..................14-61
PRESSURE LIMITING VALVE -
INSTALLATION, FUEL.................14-61
PRESSURE LIMITING VALVE -
OPERATION, FUEL....................14-61
PRESSURE LIMITING VALVE - REMOVAL,
FUEL..............................14-61
PRESSURE (LP) SENSOR -
DESCRIPTION, LINE.................21-382
PRESSURE (LP) SENSOR -
INSTALLATION, LINE.................21-383
PRESSURE (LP) SENSOR - OPERATION,
LINE..............................21-383
PRESSURE (LP) SENSOR - REMOVAL,
LINE..............................21-383
PRESSURE RELEASE - STANDARD
PROCEDURE, FUEL SYSTEM.............14-2
PRESSURE RELIEF VALVE - CLEANING,
OIL................................9-294
PRESSURE RELIEF VALVE -
DESCRIPTION, HIGH..................24-48
PRESSURE RELIEF VALVE - INSPECTION,
OIL................................9-294
PRESSURE RELIEF VALVE -
INSTALLATION, OIL...................9-294
PRESSURE RELIEF VALVE - OPERATION,
HIGH..............................24-48
PRESSURE RELIEF VALVE - REMOVAL,
OIL.................................9-294
PRESSURE SENSOR - DESCRIPTION,
FUEL..............................14-60
PRESSURE SENSOR - INSTALLATION,
FUEL..............................14-61
PRESSURE SENSOR - OPERATION, FUEL . . 14-60
PRESSURE SENSOR - REMOVAL, FUEL . . . 14-60
PRESSURE SENSOR/SWITCH -
DESCRIPTION, OIL....................9-67
PRESSURE SENSOR/SWITCH -
INSTALLATION, OIL....................9-67
PRESSURE SENSOR/SWITCH -
OPERATION, OIL......................9-67
PRESSURE SENSOR/SWITCH -
REMOVAL, OIL.......................9-67
PRESSURE, SPECIFICATIONS - FUEL
SYSTEM............................14-3
PRESSURE SWITCH - DESCRIPTION,
POWER STEERING...................19-46
PRESSURE SWITCH - INSTALLATION,
OIL................................9-294
PRESSURE SWITCH - OPERATION,
POWER STEERING...................19-46
PRESSURE SWITCH - REMOVAL, OIL.....9-294
PRESSURE TEST - DIAGNOSIS AND
TESTING, HYDRAULIC..........21-141,21-316
PRESSURE TRANSDUCER -
DESCRIPTION, A/C
...................24-15
PRESSURE TRANSDUCER - DIAGNOSIS
AND TESTING, A/C
...................24-16
PRESSURE TRANSDUCER -
INSTALLATION, A/C
...................24-16
PRESSURE TRANSDUCER - OPERATION,
A/C
................................24-16
PRESSURE TRANSDUCER - REMOVAL,
A/C
................................24-16
PRESSURES - DESCRIPTION, TIRE
INFLATION
...........................22-7
PRIMING - STANDARD PROCEDURE,
FUEL SYSTEM
.......................14-47
PROCESS - SPECIFICATIONS, WELD
.....13-15
PROGRAMING - STANDARD
PROCEDURE, RKE TRANSMITTER
........8N-9
PROGRAMMING - STANDARD
PROCEDURE, ELECTRONIC VEHICLE
INFORMATION CENTER
................8M-8
PROGRAMMING - STANDARD
PROCEDURE, ENHANCED SEATBELT
REMINDER
..........................8J-35
PROGRAMMING - STANDARD
PROCEDURE, PCM/SKIM
...............8E-14
PROGRAMMING, STANDARD
PROCEDURE - SENTRY KEY
IMMOBILIZER SYSTEM TRANSPONDER
....8Q-4PROPELLER SHAFT - DIAGNOSIS AND
TESTING.............................3-1
PROPELLER SHAFT - HD FRONT -
INSTALLATION.........................3-7
PROPELLER SHAFT - HD FRONT -
REMOVAL............................3-7
PROPELLER SHAFT - INSTALLATION,
REAR................................3-8
PROPELLER SHAFT - REMOVAL, REAR.....3-8
PROPELLER SHAFT - SPECIAL TOOLS......3-6
PROPELLER SHAFT - SPECIFICATIONS......3-6
PROPELLER SHAFT - STANDARD
PROCEDURE..........................3-3
PROPELLER SHAFT- LD FRONT -
INSTALLATION.........................3-7
PROPELLER SHAFT- LD FRONT -
REMOVAL............................3-6
PROPORTIONING - DESCRIPTION,
ELECTRONIC VARIABLE BRAKE..........5-49
PROPORTIONING - OPERATION,
ELECTRONIC VARIABLE BRAKE..........5-49
PTO SWITCH - DESCRIPTION......14-36,14-85
PTO SWITCH - OPERATION........14-36,14-85
PULLEY - INSTALLATION..............19-47
PULLEY - REMOVAL..................19-47
PUMP - 5.7L - INSTALLATION, WATER.....7-63
PUMP - 5.7L - REMOVAL, WATER........7-63
PUMP - 5.9L DIESEL - CLEANING,
WATER .............................7-62
PUMP - 5.9L DIESEL - DESCRIPTION,
WATER...............................7-62
PUMP - 5.9L DIESEL - INSPECTION,
WATER .............................7-62
PUMP - 5.9L DIESEL - INSTALLATION,
WATER .............................7-62
PUMP - 5.9L DIESEL - OPERATION,
WATER .............................7-62
PUMP - 5.9L DIESEL - REMOVAL,
WATER .............................7-62
PUMP - 8.0L - CLEANING, WATER........7-66
PUMP - 8.0L - INSPECTION, WATER......7-66
PUMP - 8.0L - INSTALLATION, WATER.....7-66
PUMP - 8.0L - REMOVAL, WATER........7-64
PUMP - ASSEMBLY, OIL...........9-158,9-69
PUMP - ASSEMBLY, OIL........21-214,21-390
PUMP - CLEANING, OIL.....9-157,9-224,9-295
PUMP - CLEANING, OIL........21-214,21-390
PUMP - DESCRIPTION................19-39
PUMP - DESCRIPTION, FUEL...........14-11
PUMP - DESCRIPTION, FUEL INJECTION . . 14-53
PUMP - DESCRIPTION, FUEL TRANSFER . . 14-64
PUMP - DESCRIPTION, LEAK DETECTION . 25-13
PUMP - DESCRIPTION, OIL......21-213,21-386
PUMP - DESCRIPTION, WATER..........7-59
PUMP - DIAGNOSIS AND TESTING,
WATER .........................7-62,7-63
PUMP - DISASSEMBLY, OIL........9-157,9-68
PUMP - DISASSEMBLY, OIL.....21-214,21-388
PUMP - INITIAL OPERATION -
STANDARD PROCEDURE, POWER
STEERING..........................19-40
PUMP - INSPECTION, OIL . . . 9-157,9-224,9-295,
9-68
PUMP - INSPECTION, OIL.......21-214,21-390
PUMP - INSTALLATION, FUEL INJECTION . 14-55
PUMP - INSTALLATION, FUEL TRANSFER . 14-65
PUMP - INSTALLATION, LEAK
DETECTION.........................25-16
PUMP - INSTALLATION, OIL . 9-159,9-225,9-296,
9-69
PUMP - OPERATION..................19-40
PUMP - OPERATION, FUEL.............14-11
PUMP - OPERATION, FUEL INJECTION....14-53
PUMP - OPERATION, FUEL TRANSFER....14-64
PUMP - OPERATION, LEAK DETECTION . . . 25-14
PUMP - OPERATION, OIL.......21-213,21-386
PUMP - OPERATION, WATER............7-60
PUMP - REMOVAL, FUEL INJECTION.....14-54
PUMP - REMOVAL, FUEL TRANSFER.....14-64
PUMP - REMOVAL, LEAK DETECTION....25-16
PUMP - REMOVAL, OIL . 9-156,9-224,9-294,9-67
PUMP BYPASS - DESCRIPTION, WATER
. . . 7-59
PUMP BYPASS - OPERATION, WATER
.....7-60
PUMP FRONT SEAL - INSTALLATION,
OIL
...............................21-391
PUMP FRONT SEAL - REMOVAL, OIL
....21-391
PUMP LEAKAGE - DIAGNOSIS AND
TESTING
...........................19-40PUMP MODULE - DESCRIPTION, FUEL....14-11
PUMP MODULE - INSTALLATION, FUEL . . . 14-12
PUMP MODULE - OPERATION, FUEL.....14-11
PUMP MODULE - REMOVAL, FUEL.......14-12
PUMP RELAY - DESCRIPTION, FUEL.....14-27
PUMP RELAY - INSTALLATION, FUEL.....14-28
PUMP RELAY - OPERATION, FUEL.......14-27
PUMP RELAY - REMOVAL, FUEL........14-28
PUMP RELAYS - DIAGNOSIS AND
TESTING, ASD AND FUEL...............8I-5
PUMP TIMING - DIAGNOSIS AND
TESTING, FUEL INJECTION.............14-53
PUMP VOLUME CHECK - STANDARD
PROCEDURE, OIL...................21-387
PUMP/MOTOR - DESCRIPTION, WASHER . 8R-13
PUMP/MOTOR - INSTALLATION,
WASHER...........................8R-14
PUMP/MOTOR - OPERATION, WASHER . . . 8R-13
PUMP/MOTOR - REMOVAL, WASHER....8R-14
PUSHRODS - CLEANING...............9-252
PUSHRODS - INSPECTION.............9-253
QUAD CAB - INSTALLATION.......8O-36,8O-61
QUAD CAB - REMOVAL..........8O-33,8O-60
QUICK CONNECT FITTING -
DESCRIPTION........................14-8
QUICK LEARN - STANDARD
PROCEDURE, TCM...................8E-23
QUICK-CONNECT FITTINGS - STANDARD
PROCEDURE...........................14-8
RADIAL - PLY TIRES - DESCRIPTION......22-6
RADIATOR - 5.9L DIESEL - CLEANING.....7-56
RADIATOR - 5.9L DIESEL -
DESCRIPTION........................7-56
RADIATOR - 5.9L DIESEL - INSPECTION . . . 7-56
RADIATOR - 5.9L DIESEL -
INSTALLATION........................7-57
RADIATOR - 5.9L DIESEL - OPERATION....7-56
RADIATOR - 5.9L DIESEL - REMOVAL.....7-56
RADIATOR CAP - DIAGNOSIS AND
TESTING............................7-58
RADIATOR CAP-TO-FILLER NECK SEAL -
DIAGNOSIS AND TESTING..............7-58
RADIATOR COOLANT FLOW -
DIAGNOSIS AND TESTING..........7-54,7-56
RADIATOR CROSSMEMBER -
INSTALLATION, UPPER................23-42
RADIATOR CROSSMEMBER - REMOVAL,
UPPER.............................23-42
RADIATOR FAN - 5.9L DIESEL -
CLEANING...........................7-35
RADIATOR FAN - 5.9L DIESEL -
INSPECTION.........................7-35
RADIATOR FAN - 5.9L DIESEL -
INSTALLATION........................7-36
RADIATOR FAN - 5.9L DIESEL -
REMOVAL...........................7-35
RADIATOR FAN - GAS ENGINES -
CLEANING...........................7-34
RADIATOR FAN - GAS ENGINES -
INSPECTION.........................7-34
RADIATOR FAN - GAS ENGINES -
INSTALLATION........................7-34
RADIATOR FAN - GAS ENGINES -
REMOVAL...........................7-33
RADIATOR PRESSURE CAP -
DESCRIPTION........................7-57
RADIATOR PRESSURE CAP - OPERATION . . 7-58
RADIATOR-3.7L/4.7L/5.7L - CLEANING.....7-55
RADIATOR-3.7L/4.7L/5.7L -
DESCRIPTION........................7-54
RADIATOR-3.7L/4.7L/5.7L - INSPECTION . . . 7-55
RADIATOR-3.7L/4.7L/5.7L -
INSTALLATION........................7-55
RADIATOR-3.7L/4.7L/5.7L - OPERATION....7-54
RADIATOR-3.7L/4.7L/5.7L - REMOVAL.....7-54
RADIO - DESCRIPTION.................8A-8
RADIO - INSTALLATION................8A-8
RADIO - OPERATION...................8A-8
RADIO - REMOVAL....................8A-8
RADIO NOISE SUPPRESSION GROUND
STRAP - DESCRIPTION
.................8A-9
RADIO NOISE SUPPRESSION GROUND
STRAP - INSTALLATION
...............8A-10
RADIO NOISE SUPPRESSION GROUND
STRAP - OPERATION
..................8A-9
RADIO NOISE SUPPRESSION GROUND
STRAP - REMOVAL
....................8A-9
RAIL - DESCRIPTION, FUEL
............14-12
DRINDEX 25
Description Group-Page Description Group-Page Description Group-Page