1998 DODGE RAM 1500 parking brake

DIAGNOSIS AND TESTING - REFRIGERANT
SYSTEM LEAKS
WARNING: R-134a SERVICE EQUIPMENT OR VEHI-
CLE A/C SYSTEM SHOULD NOT BE PRESSURE
TESTED OR LEAK TESTED WITH COMPRESSED
AIR. MIXTURE OF AIR and R-134a CAN BE COM-
BUSTIBLE AT ELEVATED PRESSURES. THESE MIX-
TURES ARE POTENTIALLY DANGEROUS AND MAY
RESULT IN FIRE OR EXPLOSION CAUSING INJURY
OR PROPERTY DAMAGE.
AVOID BREATHING A/C REFRIGERANT AND LUBRI-
CANT VAPOR OR MIST. EXPOSURE MAY IRRITATE
EYES, NOSE AND THROAT. USE ONLY APPROVED
SERVICE EQUIPMENT MEETING SAE REQUIRE-
MENTS TO DISCHARGE R-134a SYSTEM. IF ACCI-
DENTAL SYSTEM DISCHARGE OCCURS,
VENTILATE WORK AREA BEFORE RESUMING SER-
VICE.
NOTE: The refrigerant system does come from the
factory with a yellow tracer dye already installed to
aid in detection of leaks.
If the A/C system is not cooling properly, determine
if the refrigerant system is fully charged with
R-134a. This is accomplished by performing a system
Charge Level-Check or Fill. If while performing this
test A/C liquid line pressure is less than 345 kPa (50
psi) proceed to System Empty procedure. If liquid
line pressure is greater than 345 kPa (50 psi) proceed
to System Low procedure. If the refrigerant system is
empty or low in refrigerant charge, a leak at any line
fitting or component seal is likely. A review of the fit-
tings, lines and components for oily residue is an
indication of the leak location. To detect a leak in the
refrigerant system, perform one of the following pro-
cedures as indicated by the symptoms.
SYSTEM EMPTY
(1) Evacuate the refrigerant system to the lowest
degree of vacuum possible (approx. 28 in Hg.). Deter-
mine if the system holds a vacuum for 15 minutes. If
vacuum is held, a leak is probably not present. If sys-
tem will not maintain vacuum level, proceed with
this procedure.(2) Prepare a 0.284 Kg. (10 oz.) refrigerant charge
to be injected into the system.
(3) Connect and dispense 0.284 Kg. (10 oz.) of
refrigerant into the evacuated refrigerant system.
(4) Proceed to Step 2 of System Low procedure.
SYSTEM LOW
(1) Determine if there is any (R-134a) refrigerant
in the system.
(2) Position the vehicle in a wind free work area.
This will aid in detecting small leaks.
(3) Bring the refrigerant system up to operating
temperature and pressure. This is done by allowing
the engine to run for five minutes with the system
set to the following:
²Transmission in Park or Neutral with parking
brake set
²Engine idling at 700 rpm
²A/C controls set in 100 percent outside air
²Blower switch in the high A/C position
²A/C in the ON position
²Open all windows
CAUTION: A leak detector designed for R-12 refrig-
erant (only) will not detect leaks in a R-134a refrig-
erant system.
(4) Shut off the vehicle and wait 2 to 7 minutes.
Then use an Electronic Leak Detector that is
designed to detect R-134a type refrigerant and search
for leaks. Fittings, lines, or components that appear
to be oily usually indicates a refrigerant leak. To
inspect the evaporator core for leaks, insert the leak
detector probe into the drain tube opening or a heat
duct. A R-134a dye is available to aid in leak detec-
tion, use only DaimlerChrysler approved refrigerant
dye.
24 - 44 PLUMBINGDR
PLUMBING (Continued)

BLOCK - DIAGNOSIS AND TESTING,
BLOWER MOTOR RESISTOR............24-19
BLOCK - INSPECTION, ENGINE . 9-128,9-205,9-39
BLOCK - INSTALLATION, BLOWER
MOTOR RESISTOR...................24-19
BLOCK - INSTALLATION, BRAKE
JUNCTION...........................5-24
BLOCK - OPERATION, BLOWER MOTOR
RESISTOR..........................24-18
BLOCK - REMOVAL, BLOWER MOTOR
RESISTOR..........................24-19
BLOCK - REMOVAL, BRAKE JUNCTION....5-24
BLOCK HEATER - 5.9L DIESEL -
DESCRIPTION, ENGINE.................7-37
BLOCK HEATER - 5.9L DIESEL -
INSTALLATION, ENGINE................7-38
BLOCK HEATER - 5.9L DIESEL -
OPERATION, ENGINE...................7-38
BLOCK HEATER - 5.9L DIESEL -
REMOVAL, ENGINE....................7-38
BLOCK HEATER - DESCRIPTION, ENGINE . . . 7-36
BLOCK HEATER - DIAGNOSIS AND
TESTING, ENGINE.....................7-36
BLOCK HEATER - INSTALLATION,
ENGINE.............................7-37
BLOCK HEATER - OPERATION, ENGINE....7-36
BLOCK HEATER - REMOVAL, ENGINE......7-37
BLOCK REFACING - STANDARD
PROCEDURE, CYLINDER...............9-264
BLOWER MOTOR - DESCRIPTION.......24-28
BLOWER MOTOR - DIAGNOSIS AND
TESTING.............................24-28
BLOWER MOTOR - INSTALLATION.......24-31
BLOWER MOTOR - OPERATION.........24-28
BLOWER MOTOR - REMOVAL...........24-31
BLOWER MOTOR RESISTOR BLOCK -
DESCRIPTION.......................24-18
BLOWER MOTOR RESISTOR BLOCK -
DIAGNOSIS AND TESTING.............24-19
BLOWER MOTOR RESISTOR BLOCK -
INSTALLATION.......................24-19
BLOWER MOTOR RESISTOR BLOCK -
OPERATION.........................24-18
BLOWER MOTOR RESISTOR BLOCK -
REMOVAL..........................24-19
BLOWER MOTOR SWITCH -
DESCRIPTION.......................24-20
BLOWER MOTOR SWITCH - DIAGNOSIS
AND TESTING.......................24-20
BLOWER MOTOR SWITCH - OPERATION . . 24-20
BODY - ADJUSTMENTS, VALVE........21-310
BODY - ASSEMBLY, VALVE......21-299,21-414
BODY & CABLE - DESCRIPTION,
ANTENNA...........................8A-4
BODY & CABLE - INSTALLATION,
ANTENNA...........................8A-6
BODY & CABLE - OPERATION, ANTENNA . . . 8A-4
BODY & CABLE - REMOVAL, ANTENNA....8A-6
BODY - CLEANING, VALVE......21-298,21-412
BODY - DESCRIPTION, THROTTLE.......14-36
BODY - DESCRIPTION, VALVE....21-267,21-408
BODY - DISASSEMBLY, VALVE . . . 21-287,21-410
BODY - INSPECTION, VALVE.....21-298,21-413
BODY - INSTALLATION, THROTTLE.......14-37
BODY - INSTALLATION, VALVE . . . 21-309,21-414
BODY - OPERATION, THROTTLE.........14-36
BODY - OPERATION, VALVE.....21-272,21-408
BODY - REMOVAL, THROTTLE..........14-36
BODY - REMOVAL, VALVE.......21-286,21-410
BODY AND CABLE - DIAGNOSIS AND
TESTING, ANTENNA
...................8A-4
BODY CODE PLATE - DESCRIPTION
.....Intro.-3
BODY ISOLATORS - INSTALLATION
......23-37
BODY ISOLATORS - REMOVAL
..........23-36
BODY LUBRICATION - STANDARD
PROCEDURE
.........................23-3
BODY OPENING DIMENSIONS -
SPECIFICATIONS
.....................23-99
BODY PANEL REPAIR - STANDARD
PROCEDURE, PLASTIC
.................23-3
BODY SIDE MOLDINGS - INSTALLATION
. . 23-36
BODY SIDE MOLDINGS - REMOVAL
......23-36
BODY, SPECIAL TOOLS
................23-14
BODY VENT - INSTALLATION
...........23-71
BODY VENT - REMOVAL
...............23-71
BOOST PRESSURE - DIAGNOSIS AND
TESTING, TURBOCHARGER
.............11-11BOOSTER - DESCRIPTION, POWER
BRAKE..............................5-29
BOOSTER - DIAGNOSIS AND TESTING,
HYDRAULIC..........................5-30
BOOSTER - DIAGNOSIS AND TESTING,
MASTER CYLINDER/POWER.............5-25
BOOSTER - INSTALLATION, HYDRO-
BOOST BRAKE........................5-32
BOOSTER - INSTALLATION, POWER
BRAKE..............................5-29
BOOSTER - OPERATION, POWER BRAKE . . . 5-29
BOOSTER - REMOVAL, HYDRO-BOOST
BRAKE..............................5-31
BOOSTER - REMOVAL, POWER BRAKE....5-29
BOOT - INSTALLATION, 4WD FLOOR
SHIFT..............................23-62
BOOT - INSTALLATION, EXTENSION
HOUSING SEAL AND DUST......21-476,21-571
BOOT - REMOVAL, 4WD FLOOR SHIFT....23-62
BOOT - REMOVAL, EXTENSION HOUSING
SEAL AND DUST..............21-476,21-571
BORE - DE-GLAZE - STANDARD
PROCEDURE, CYLINDER...............9-264
BORE HONING - STANDARD
PROCEDURE, CYLINDER...........9-128,9-38
BORE REPAIR - STANDARD
PROCEDURE, CAM...................9-267
BORE REPAIR - STANDARD
PROCEDURE, CYLINDER...............9-265
BOX - INSTALLATION, CARGO..........23-37
BOX - INSTALLATION, GLOVE...........23-52
BOX - INSTALLATION, WITH CARGO . 8L-22,8L-23,
8L-24,8L-7,8L-9
BOX - INSTALLATION, WITHOUT CARGO . . 8L-22,
8L-23,8L-24,8L-8,8L-9
BOX - REMOVAL, CARGO..............23-37
BOX - REMOVAL, GLOVE..............23-52
BOX - REMOVAL, WITH CARGO....8L-22,8L-24,
8L-7,8L-9
BOX - REMOVAL, WITHOUT CARGO.....8L-22,
8L-23,8L-24,8L-7,8L-9
BOX - TIE DOWN - INSTALLATION,
CARGO............................23-38
BOX - TIE DOWN - REMOVAL, CARGO....23-38
BOX LAMP/SWITCH - INSTALLATION,
GLOVE.............................8L-28
BOX LAMP/SWITCH - REMOVAL, GLOVE . . 8L-27
BOX LATCH - INSTALLATION, GLOVE.....23-52
BOX LATCH - REMOVAL, GLOVE.........23-52
B-PILLAR GRAB HANDLE -
INSTALLATION.......................23-68
B-PILLAR GRAB HANDLE - REMOVAL....23-68
B-PILLAR LOWER TRIM - INSTALLATION . . 23-64
B-PILLAR LOWER TRIM - REMOVAL.....23-63
B-PILLAR UPPER TRIM - INSTALLATION . . 23-64
B-PILLAR UPPER TRIM - REMOVAL......23-64
BRACKET - INSTALLATION, REAR VIEW
MIRROR SUPPORT...................23-70
BRACKET - INSTALLATION, STEERING
COLUMN OPENING SUPPORT...........23-60
BRACKET - REMOVAL, STEERING
COLUMN OPENING SUPPORT...........23-60
BRACKETS - INSTALLATION, SEAT BACK
REAR - FOOTMANS LOOP..............23-85
BRACKETS - REMOVAL, SEAT BACK
REAR - FOOTMANS LOOP..............23-85
BRAKE - CLEANING, REAR DRUM IN
HAT ................................5-39
BRAKE - DESCRIPTION, CONTROLLER
ANTILOCK...........................8E-3
BRAKE - DESCRIPTION, PARKING........5-36
BRAKE - INSPECTION, REAR DRUM IN
HAT ................................5-39
BRAKE - INSTALLATION, CONTROLLER
ANTILOCK...........................8E-3
BRAKE - OPERATION, CONTROLLER
ANTILOCK...........................8E-3
BRAKE - OPERATION, PARKING..........5-36
BRAKE - REMOVAL, CONTROLLER
ANTILOCK
...........................8E-3
BRAKE BLEEDING - STANDARD
PROCEDURE, ABS
.....................5-46
BRAKE BOOSTER - DESCRIPTION,
POWER
.............................5-29
BRAKE BOOSTER - INSTALLATION,
HYDRO-BOOST
.......................5-32
BRAKE BOOSTER - INSTALLATION,
POWER
.............................5-29BRAKE BOOSTER - OPERATION, POWER . . . 5-29
BRAKE BOOSTER - REMOVAL,
HYDRO-BOOST.......................5-31
BRAKE BOOSTER - REMOVAL, POWER....5-29
BRAKE CABLE - INSTALLATION, FRONT
PARKING............................5-38
BRAKE CABLE - INSTALLATION, REAR
PARK...............................5-38
BRAKE CABLE - REMOVAL, FRONT
PARKING............................5-36
BRAKE CABLE - REMOVAL, REAR PARK . . . 5-37
BRAKE CALIPER ADAPTER MOUNT -
INSTALLATION, DISC...................5-22
BRAKE CALIPERS - DESCRIPTION, DISC . . . 5-16
BRAKE CALIPERS - OPERATION, DISC.....5-16
BRAKE FLUID CONTAMINATION -
DIAGNOSIS AND TESTING..............5-23
BRAKE FLUID LEVEL - STANDARD
PROCEDURE.........................5-23
BRAKE FLUID, SPECIFICATIONS..........5-23
BRAKE HOSE - INSTALLATION, FRONT.....5-13
BRAKE HOSE - INSTALLATION, REAR......5-12
BRAKE HOSE - REMOVAL, REAR.........5-11
BRAKE INDICATOR - DESCRIPTION,
BRAKE/PARK........................8J-19
BRAKE INDICATOR - DIAGNOSIS AND
TESTING...........................8J-20
BRAKE INDICATOR - OPERATION,
BRAKE/PARK........................8J-19
BRAKE JUNCTION BLOCK -
INSTALLATION.........................5-24
BRAKE JUNCTION BLOCK - REMOVAL.....5-24
BRAKE LAMP SWITCH - DESCRIPTION....8L-9
BRAKE LAMP SWITCH - DIAGNOSIS
AND TESTING.......................8L-10
BRAKE LAMP SWITCH - INSTALLATION . . . 8L-11
BRAKE LAMP SWITCH - OPERATION......8L-9
BRAKE LAMP SWITCH - REMOVAL......8L-10
BRAKE PROPORTIONING -
DESCRIPTION, ELECTRONIC VARIABLE....5-49
BRAKE PROPORTIONING - OPERATION,
ELECTRONIC VARIABLE................5-49
BRAKE ROTOR, DIAGNOSIS AND
TESTING - DISC......................5-32
BRAKE SHOES - ADJUSTMENT, PARKING . . 5-41
BRAKE, SPECIFICATIONS - BASE.........5-10
BRAKE SYSTEM - DIAGNOSIS AND
TESTING, BASE........................5-2
BRAKE TRANSMISSION SHIFT
INTERLOCK - ADJUSTMENTS....21-196,21-365
BRAKE TRANSMISSION SHIFT
INTERLOCK - DIAGNOSIS AND
TESTING....................21-196,21-364
BRAKE TRANSMISSION SHIFT
INTERLOCK SYSTEM - DESCRIPTION . . . 21-196,
21-364
BRAKE TRANSMISSION SHIFT
INTERLOCK SYSTEM - OPERATION.....21-196,
21-364
BRAKE/PARK BRAKE INDICATOR -
DESCRIPTION.......................8J-19
BRAKE/PARK BRAKE INDICATOR -
OPERATION.........................8J-19
BRAKES - ABS - DESCRIPTION...........5-45
BRAKES - ABS - OPERATION............5-45
BRAKES, SPECIAL TOOLS - BASE.........5-5
BREAK-IN - STANDARD PROCEDURE,
A/C COMPRESSOR CLUTCH............24-10
BREATHER - INSTALLATION,
CRANKCASE
........................9-243
BREATHER - REMOVAL, CRANKCASE
.....9-242
BUCKLE - INSTALLATION, FRONT
OUTBOARD SEAT BELT
................8O-38
BUCKLE - REMOVAL, FRONT OUTBOARD
SEAT BELT
.........................8O-37
BUILT-IN INDICATOR TEST - STANDARD
PROCEDURE
........................8F-10
BUMPER - INSTALLATION, FRONT
........13-2
BUMPER - INSTALLATION, JOUNCE
.......2-43
BUMPER - INSTALLATION, REAR
.........13-4
BUMPER - REMOVAL, FRONT
............13-2
BUMPER - REMOVAL, JOUNCE
...........2-43
BUMPER - REMOVAL, REAR
.............13-3
BUMPERS (3500) - INSTALLATION,
AUXILIARY SPRING
....................2-43
BUMPERS (3500) - REMOVAL,
AUXILIARY SPRING
....................2-43
4 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

BURNT FLUID - DIAGNOSIS AND
TESTING, CAUSES OF..........21-201,21-366
BUSHING - INSTALLATION.............19-19
BUSHING - INSTALLATION, TORSION
BAR CROSS MEMBER..................2-15
BUSHING - REMOVAL.................19-19
BUSHING - REMOVAL, TORSION BAR
CROSSMEMBER......................2-13
BUSHING AND SEAL - INSTALLATION,
EXTENSION HOUSING................21-440
BUSHING AND SEAL - REMOVAL,
EXTENSION HOUSING................21-440
BUSHINGS - 2WD (LD) - INSTALLATION,
LOWER CONTROL ARM................2-15
BUSHINGS - 2WD (LD) - REMOVAL,
LOWER CONTROL ARM................2-13
BUSHINGS - 4WD (LD) - INSTALLATION,
LOWER CONTROL ARM................2-14
BUSHINGS - 4WD (LD) - REMOVAL,
LOWER CONTROL ARM................2-13
BUSHINGS - INSTALLATION.............2-43
BUSHINGS - REMOVAL.................2-43
BUZZ, SQUEAK & RATTLE - STANDARD
PROCEDURE........................23-11
BYPASS - DESCRIPTION, WATER PUMP . . . 7-59
BYPASS - OPERATION, WATER PUMP.....7-60
C205F - ADJUSTMENTS, FRONT AXLE.....3-32
C205F - DIAGNOSIS AND TESTING,
FRONT AXLE.........................3-27
C205F - INSTALLATION, FRONT AXLE.....3-31
C205F - REMOVAL, FRONT AXLE...........3-31
C205F - SPECIAL TOOLS, FRONT AXLE....3-40
C205F - SPECIFICATIONS, FRONT AXLE....3-39
CAB - INSTALLATION, QUAD......8O-36,8O-61
CAB - INSTALLATION, STANDARD . . 8O-35,8O-61
CAB - REMOVAL, QUAD..........8O-33,8O-60
CAB - REMOVAL, STANDARD......8O-32,8O-59
CAB BACK PANEL TRIM -
INSTALLATION, REAR.................23-69
CAB BACK PANEL TRIM - REMOVAL,
REAR..............................23-68
CAB CLEARANCE LAMP - INSTALLATION . . 8L-12
CAB CLEARANCE LAMP - REMOVAL.....8L-11
CABLE - ADJUSTMENTS, THROTTLE
VALVE ............................21-254
CABLE - DESCRIPTION.................8P-4
CABLE - DESCRIPTION, ANTENNA BODY . . . 8A-4
CABLE - DESCRIPTION, SPARK PLUG.....8I-21
CABLE - DESCRIPTION, THROTTLE
VALVE ............................21-253
CABLE - DIAGNOSIS AND TESTING,
ANTENNA BODY......................8A-4
CABLE - DIAGNOSIS AND TESTING,
GEARSHIFT..................21-210,21-368
CABLE - INSTALLATION................8P-5
CABLE - INSTALLATION, ANTENNA BODY . . 8A-6
CABLE - INSTALLATION, CHECK.........23-15
CABLE - INSTALLATION, FRONT
PARKING BRAKE......................5-38
CABLE - INSTALLATION, GEARSHIFT....21-211,
21-370
CABLE - INSTALLATION, INSTRUMENT
PANEL ANTENNA......................8A-7
CABLE - INSTALLATION, LEFT REAR......5-39
CABLE - INSTALLATION, REAR PARK
BRAKE..............................5-38
CABLE - INSTALLATION, RIGHT REAR.....5-38
CABLE - INSTALLATION, SPARK PLUG....8I-22
CABLE - INSTALLATION, THROTTLE
CONTROL.....................14-40,14-84
CABLE - OPERATION...................8P-4
CABLE - OPERATION, ANTENNA BODY
.....8A-4
CABLE - OPERATION, SPARK PLUG
.......8I-21
CABLE - REMOVAL
....................8P-4
CABLE - REMOVAL, ANTENNA BODY
......8A-6
CABLE - REMOVAL, CHECK
.............23-15
CABLE - REMOVAL, FRONT PARKING
BRAKE
..............................5-36
CABLE - REMOVAL, GEARSHIFT
. . 21-210,21-369
CABLE - REMOVAL, INSTRUMENT PANEL
ANTENNA
...........................8A-7
CABLE - REMOVAL, LEFT REAR
..........5-38
CABLE - REMOVAL, REAR PARK BRAKE
. . . 5-37
CABLE - REMOVAL, RIGHT REAR
.........5-37
CABLE - REMOVAL, SPARK PLUG
........8I-22
CABLE - REMOVAL, THROTTLE
CONTROL
.....................14-38,14-83CABLE, ADJUSTMENTS - GEARSHIFT . . . 21-212,
21-370
CABLE RESISTANCE, SPECIFICATIONS -
SPARK PLUG.........................8I-4
CABLE ROUTING, 5.7L V-8 ENGINE -
FIRING ORDER........................8I-4
CABLE/HANDLE ASSEMBLY -
INSTALLATION, LATCH RELEASE........23-47
CABLE/HANDLE ASSEMBLY - REMOVAL,
LATCH RELEASE.....................23-47
CABLES - DESCRIPTION, BATTERY.......8F-14
CABLES - DIAGNOSIS AND TESTING,
BATTERY...........................8F-15
CABLES - INSTALLATION, BATTERY......8F-17
CABLES - OPERATION, BATTERY........8F-15
CABLES - REMOVAL, BATTERY..........8F-16
CALIBRATION - STANDARD PROCEDURE,
COMPASS...........................8M-3
CALIPER ADAPTER MOUNT -
INSTALLATION, DISC BRAKE............5-22
CALIPERS - DESCRIPTION, DISC BRAKE . . . 5-16
CALIPERS - OPERATION, DISC BRAKE.....5-16
CAM BORE REPAIR - STANDARD
PROCEDURE........................9-267
CAMBER AND CASTER ADJUSTMENT -
STANDARD PROCEDURE.................2-4
CAMBER, CASTER AND TOE
ADJUSTMENT - STANDARD
PROCEDURE..........................2-4
CAM/OVERDRIVE PISTON RETAINER -
ASSEMBLY, OVERRUNNING CLUTCH....21-237
CAM/OVERDRIVE PISTON RETAINER -
CLEANING, OVERRUNNING CLUTCH.....21-236
CAM/OVERDRIVE PISTON RETAINER -
DESCRIPTION, OVERRUNNING CLUTCH . . 21-236
CAM/OVERDRIVE PISTON RETAINER -
DISASSEMBLY, OVERRUNNING
CLUTCH...........................21-236
CAM/OVERDRIVE PISTON RETAINER -
INSPECTION, OVERRUNNING CLUTCH . . . 21-237
CAM/OVERDRIVE PISTON RETAINER -
OPERATION, OVERRUNNING CLUTCH....21-236
CAMSHAFT - INSTALLATION.......9-206,9-271
CAMSHAFT - REMOVAL..........9-205,9-268
CAMSHAFT BEARINGS - INSTALLATION . . . 9-271
CAMSHAFT BEARINGS - REMOVAL......9-268
CAMSHAFT CORE HOLE PLUG -
INSTALLATION.......................9-206
CAMSHAFT CORE HOLE PLUG -
REMOVAL..........................9-205
CAMSHAFT POSITION SENSOR -
DESCRIPTION.......................14-71
CAMSHAFT POSITION SENSOR -
DESCRIPTION.........................8I-7
CAMSHAFT POSITION SENSOR -
INSTALLATION.......................14-72
CAMSHAFT POSITION SENSOR -
INSTALLATION.......................8I-10
CAMSHAFT POSITION SENSOR -
OPERATION.........................14-71
CAMSHAFT POSITION SENSOR -
OPERATION..........................8I-7
CAMSHAFT POSITION SENSOR -
REMOVAL..........................14-72
CAMSHAFT POSITION SENSOR -
REMOVAL............................8I-9
CAMSHAFT(S) - DESCRIPTION.......9-25,9-35
CAMSHAFT(S) - INSTALLATION......9-27,9-36
CAMSHAFT(S) - LEFT - DESCRIPTION....9-114
CAMSHAFT(S) - LEFT - INSTALLATION....9-116
CAMSHAFT(S) - LEFT - REMOVAL.......9-115
CAMSHAFT(S) - REMOVAL..........9-25,9-35
CAMSHAFT(S) - RIGHT - DESCRIPTION . . . 9-119
CAMSHAFT(S) - RIGHT - INSTALLATION . . 9-120
CAMSHAFT(S) - RIGHT - REMOVAL......9-119
CANISTER - DESCRIPTION, VAPOR......25-22
CANISTER - INSTALLATION, VAPOR......25-22
CANISTER - OPERATION, VAPOR........25-22
CANISTER - REMOVAL, VAPOR..........25-22
CAP - DESCRIPTION, FUEL FILLER.......25-13
CAP - DESCRIPTION, RADIATOR
PRESSURE
..........................7-57
CAP - DIAGNOSIS AND TESTING,
RADIATOR
...........................7-58
CAP - OPERATION, FUEL FILLER
........25-13
CAP - OPERATION, RADIATOR
PRESSURE
..........................7-58
CAPACITIES, SPECIFICATIONS - FLUID
......0-5CAPACITOR - DESCRIPTION, IGNITION
COIL...............................8I-21
CAPACITOR - INSTALLATION, IGNITION
COIL...............................8I-21
CAPACITOR - OPERATION, IGNITION
COIL...............................8I-21
CAPACITOR - REMOVAL, IGNITION COIL . . . 8I-21
CAP-TO-FILLER NECK SEAL -
DIAGNOSIS AND TESTING, RADIATOR.....7-58
CARDAN UNIVERSAL JOINTS -
ASSEMBLY, DOUBLE...................3-17
CARDAN UNIVERSAL JOINTS -
DISASSEMBLY, DOUBLE................3-16
CARGO BOX - INSTALLATION...........23-37
CARGO BOX - INSTALLATION, WITH.....8L-22,
8L-23,8L-24,8L-7,8L-9
CARGO BOX - INSTALLATION, WITHOUT . . 8L-22,
8L-23,8L-24,8L-8,8L-9
CARGO BOX - REMOVAL...............23-37
CARGO BOX - REMOVAL, WITH....8L-22,8L-24,
8L-7,8L-9
CARGO BOX - REMOVAL, WITHOUT.....8L-22,
8L-23,8L-24,8L-7,8L-9
CARGO BOX - TIE DOWN -
INSTALLATION.......................23-38
CARGO BOX - TIE DOWN - REMOVAL....23-38
CARGO LAMP INDICATOR -
DESCRIPTION.......................8J-20
CARGO LAMP INDICATOR - OPERATION . . 8J-20
CARPETS AND FLOOR MATS -
INSTALLATION.......................23-65
CARPETS AND FLOOR MATS - REMOVAL . . . 23-65
CASCADE OVERFLOW VALVE -
DESCRIPTION.......................14-66
CASCADE OVERFLOW VALVE -
OPERATION.........................14-66
CASE - DESCRIPTION, TRANSFER.........0-4
CASE - NV241 GENII - ASSEMBLY,
TRANSFER.........................21-428
CASE - NV241 GENII - CLEANING,
TRANSFER.........................21-426
CASE - NV241 GENII - DESCRIPTION,
TRANSFER.........................21-415
CASE - NV241 GENII - DIAGNOSIS AND
TESTING, TRANSFER.................21-416
CASE - NV241 GENII - DISASSEMBLY,
TRANSFER.........................21-417
CASE - NV241 GENII - INSPECTION,
TRANSFER.........................21-426
CASE - NV241 GENII - INSTALLATION,
TRANSFER.........................21-438
CASE - NV241 GENII - OPERATION,
TRANSFER.........................21-415
CASE - NV241 GENII - REMOVAL,
TRANSFER.........................21-417
CASE - NV243 - ASSEMBLY, TRANSFER . . 21-496
CASE - NV243 - CLEANING, TRANSFER . . 21-493
CASE - NV243 - DESCRIPTION,
TRANSFER.........................21-482
CASE - NV243 - DIAGNOSIS AND
TESTING, TRANSFER.................21-483
CASE - NV243 - DISASSEMBLY,
TRANSFER.........................21-484
CASE - NV243 - INSPECTION, TRANSFER . 21-493
CASE - NV243 - INSTALLATION,
TRANSFER.........................21-505
CASE - NV243 - OPERATION, TRANSFER . 21-483
CASE - NV243 - REMOVAL, TRANSFER . . 21-484
CASE - NV244 - DIAGNOSIS AND
TESTING, TRANSFER.................21-513
CASE - NV244 GENII - ASSEMBLY,
TRANSFER.........................21-525
CASE - NV244 GENII - CLEANING,
TRANSFER.........................21-523
CASE - NV244 GENII - DESCRIPTION,
TRANSFER.........................21-512
CASE - NV244 GENII - DISASSEMBLY,
TRANSFER.........................21-514
CASE - NV244 GENII - INSPECTION,
TRANSFER.........................21-523
CASE - NV244 GENII - INSTALLATION,
TRANSFER
.........................21-534
CASE - NV244 GENII - OPERATION,
TRANSFER
.........................21-513
CASE - NV244 GENII - REMOVAL,
TRANSFER
.........................21-514
CASE - NV271 - ASSEMBLY, TRANSFER
. . 21-461
CASE - NV271 - CLEANING, TRANSFER
. . 21-459
DRINDEX 5
Description Group-Page Description Group-Page Description Group-Page

FIRING ORDER / CABLE ROUTING, 5.7L
V-8 ENGINE..........................8I-4
FIRING ORDER, 3.7L V-6 - ENGINE........8I-4
FIRING ORDER, 4.7L V-8 - ENGINE........8I-4
FIRING ORDER, DIESEL - FUEL
INJECTOR..........................14-48
FITTING - DESCRIPTION, QUICK
CONNECT............................14-8
FITTING - STANDARD PROCEDURE,
CONNECTING ROD BEARING...........9-129
FITTING - STANDARD PROCEDURE,
CRANKSHAFT MAIN BEARING.....9-134,9-207
FITTING - STANDARD PROCEDURE,
PISTON...................9-139,9-211,9-51
FITTING - STANDARD PROCEDURE,
PISTON RING.........9-142,9-213,9-284,9-53
FITTING, STANDARD PROCEDURE -
CONNECTING ROD BEARING............9-49
FITTING, STANDARD PROCEDURE -
MAIN BEARING.......................9-44
FITTINGS - STANDARD PROCEDURE,
HANDLING TUBING...................24-45
FITTINGS - STANDARD PROCEDURE,
QUICK-CONNECT......................14-8
FLAG - INSTALLATION, SIDE VIEW
MIRROR...........................23-27
FLAG - REMOVAL, SIDE VIEW MIRROR . . . 23-27
FLARING - STANDARD PROCEDURE,
DOUBLE INVERTED....................5-10
FLARING - STANDARD PROCEDURE, ISO . . . 5-11
FLEX PLATE - INSTALLATION . . 9-138,9-210,9-48
FLEX PLATE - REMOVAL.......9-138,9-210,9-48
FLOOR - INSTALLATION, LOAD..........23-72
FLOOR - REMOVAL, LOAD.............23-71
FLOOR CONSOLE - INSTALLATION.......23-67
FLOOR CONSOLE - REMOVAL...........23-67
FLOOR DISTRIBUTION DUCT -
INSTALLATION.......................24-34
FLOOR DISTRIBUTION DUCT - REMOVAL . 24-33
FLOOR MATS - INSTALLATION, CARPETS . 23-65
FLOOR MATS - REMOVAL, CARPETS.....23-65
FLOOR SHIFT BOOT - INSTALLATION,
4WD ..............................23-62
FLOOR SHIFT BOOT - REMOVAL, 4WD....23-62
FLOOR SUPPORT CYLINDER -
INSTALLATION, LOAD.................23-72
FLOOR SUPPORT CYLINDER -
REMOVAL, LOAD.....................23-72
FLOW - 5.9L DIESEL - DESCRIPTION,
COOLING SYSTEM.....................7-3
FLOW - DIAGNOSIS AND TESTING,
RADIATOR COOLANT..............7-54,7-56
FLOW 3.7L/4.7L/5.7L ENGINE -
DESCRIPTION, COOLING SYSTEM.........7-1
FLOW AND PRESSURE - DIAGNOSIS
AND TESTING, POWER STEERING........19-4
FLUID - DESCRIPTION................19-43
FLUID - DESCRIPTION, AUTOMATIC
TRANSMISSION.......................0-4
FLUID - DESCRIPTION, POWER
STEERING............................0-3
FLUID - DIAGNOSIS AND TESTING,
CAUSES OF BURNT............21-201,21-366
FLUID - OPERATION, AUTOMATIC
TRANSMISSION.......................0-5
FLUID AND FILTER REPLACEMENT -
STANDARD PROCEDURE........21-203,21-367
FLUID CAPACITIES, SPECIFICATIONS.......0-5
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING................21-202,21-366
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING, BRAKE..................5-23
FLUID COOLER - INSTALLATION.........19-43
FLUID COOLER - REMOVAL............19-43
FLUID DRAIN AND REFILL - STANDARD
PROCEDURE.....21-441,21-476,21-507,21-537,
21-571
FLUID INDICATOR - DESCRIPTION,
WASHER
...........................8J-44
FLUID INDICATOR - OPERATION,
WASHER
...........................8J-44
FLUID LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING
.........21-144,21-318
FLUID LEVEL - DIAGNOSIS AND
TESTING, EFFECTS OF INCORRECT
.....21-201,
21-366
FLUID LEVEL - STANDARD PROCEDURE,
BRAKE
..............................5-23FLUID LEVEL CHECK - STANDARD
PROCEDURE.................21-202,21-366
FLUID LEVEL CHECKING - STANDARD
PROCEDURE, POWER STEERING........19-43
FLUID LEVEL SWITCH - DESCRIPTION,
WASHER............................8R-9
FLUID LEVEL SWITCH - INSTALLATION,
WASHER...........................8R-11
FLUID LEVEL SWITCH - OPERATION,
WASHER............................8R-9
FLUID LEVEL SWITCH - REMOVAL,
WASHER...........................8R-10
FLUID RESERVOIR - INSTALLATION.......5-24
FLUID RESERVOIR - REMOVAL..........5-23
FLUID, SPECIFICATIONS - BRAKE.........5-23
FLUSH - SPECIFICATIONS, GAP.........23-95
FLUSHING - STANDARD PROCEDURE,
COOLING SYSTEM CLEANING/
REVERSE............................7-17
FLUSHING POWER STEERING SYSTEM -
STANDARD PROCEDURE...............19-40
FLYWHEEL - ASSEMBLY................6-11
FLYWHEEL - DIAGNOSIS AND TESTING....6-10
FLYWHEEL - DISASSEMBLY.............6-11
FLYWHEEL - INSTALLATION.............6-11
FLYWHEEL - REMOVAL.................6-11
FOG LAMP - INSTALLATION............8L-12
FOG LAMP - REMOVAL................8L-12
FOG LAMP RELAY - DESCRIPTION.......8L-12
FOG LAMP RELAY - INSTALLATION........8L-13
FOG LAMP RELAY - OPERATION.........8L-13
FOG LAMP RELAY - REMOVAL..........8L-13
FOOTMANS LOOP BRACKETS -
INSTALLATION, SEAT BACK REAR.......23-85
FOOTMANS LOOP BRACKETS -
REMOVAL, SEAT BACK REAR...........23-85
FORM-IN-PLACE GASKETS AND
SEALERS - STANDARD PROCEDURE . . 9-239,9-9,
9-94
FRAME - INSTALLATION, GRILLE........23-40
FRAME - REAR - INSTALLATION, SEAT
CUSHION...........................23-85
FRAME - REAR - REMOVAL, SEAT
CUSHION...........................23-85
FRAME - REMOVAL, GRILLE............23-40
FRAME DIMENSIONS - SPECIFICATIONS . . 13-16
FRAME H-SECTION REPLACEMENT -
STANDARD PROCEDURE, REAR.........13-13
FRAME RAIL TIP REPLACEMENT -
STANDARD PROCEDURE, LIGHT DUTY
FRONT..............................13-4
FREE MODULE - INSTALLATION, HANDS . . . 8T-2
FREE MODULE - REMOVAL, HANDS.......8T-2
FRONT - INSTALLATION....5-16,5-21,5-22,5-34
FRONT - INSTALLATION...............22-14
FRONT - INSTALLATION, CRANKSHAFT
OIL SEAL.............9-136,9-208,9-275,9-46
FRONT - INSTALLATION, PROPELLER
SHAFT - HD...........................3-7
FRONT - INSTALLATION, PROPELLER
SHAFT- LD............................3-7
FRONT - INSTALLATION, SEAT..........23-81
FRONT - INSTALLATION, SEAT BACK
CUSHION / COVER...................23-82
FRONT - INSTALLATION, SEAT CUSHION
/ COVER............................23-83
FRONT - REMOVAL........5-13,5-17,5-21,5-33
FRONT - REMOVAL, CRANKSHAFT OIL
SEAL................9-135,9-208,9-275,9-46
FRONT - REMOVAL, PROPELLER SHAFT
- HD ................................3-7
FRONT - REMOVAL, PROPELLER SHAFT-
LD ..................................3-6
FRONT - REMOVAL, SEAT..............23-81
FRONT - REMOVAL, SEAT BACK
CUSHION / COVER...................23-82
FRONT - REMOVAL, SEAT CUSHION /
COVER.............................23-83
FRONT AIR DAM - INSTALLATION........13-2
FRONT AIR DAM - REMOVAL............13-2
FRONT AXLE - 9 1/4 AA -
ADJUSTMENTS
.......................3-59
FRONT AXLE - 9 1/4 AA - DIAGNOSIS
AND TESTING
........................3-54
FRONT AXLE - 9 1/4 AA - INSTALLATION
. . . 3-58
FRONT AXLE - 9 1/4 AA - REMOVAL
......3-57
FRONT AXLE - 9 1/4 AA - SPECIAL
TOOLS
..............................3-64FRONT AXLE - 9 1/4 AA -
SPECIFICATIONS......................3-63
FRONT AXLE - C205F - ADJUSTMENTS....3-32
FRONT AXLE - C205F - DIAGNOSIS AND
TESTING............................3-27
FRONT AXLE - C205F - INSTALLATION.....3-31
FRONT AXLE - C205F - REMOVAL........3-31
FRONT AXLE - C205F - SPECIAL TOOLS . . . 3-40
FRONT AXLE - C205F - SPECIFICATIONS . . . 3-39
FRONT BEARING - INSTALLATION,
OUTPUT SHAFT.....................21-216
FRONT BEARING - REMOVAL, OUTPUT
SHAFT............................21-216
FRONT BRAKE HOSE - INSTALLATION.....5-13
FRONT BUMPER - INSTALLATION.........13-2
FRONT BUMPER - REMOVAL............13-2
FRONT CENTER SEAT BELT -
INSTALLATION......................8O-31
FRONT CENTER SEAT BELT - REMOVAL . . 8O-30
FRONT CENTER SEAT BELT &
RETRACTOR - INSTALLATION...........8O-29
FRONT CENTER SEAT BELT &
RETRACTOR - REMOVAL..............8O-29
FRONT CLUTCH - ASSEMBLY..........21-207
FRONT CLUTCH - DESCRIPTION........21-205
FRONT CLUTCH - DISASSEMBLY.......21-205
FRONT CLUTCH - INSPECTION.........21-206
FRONT CLUTCH - OPERATION.........21-205
FRONT CONTROL MODULE -
DESCRIPTION.....................8W-97-5
FRONT CONTROL MODULE -
DESCRIPTION........................8E-5
FRONT CONTROL MODULE - DIAGNOSIS
AND TESTING.....................8W-97-5
FRONT CONTROL MODULE - DIAGNOSIS
AND TESTING........................8E-5
FRONT CONTROL MODULE -
INSTALLATION....................8W-97-6
FRONT CONTROL MODULE -
INSTALLATION........................8E-5
FRONT CONTROL MODULE - OPERATION . 8W-97-5
FRONT CONTROL MODULE - OPERATION . . 8E-5
FRONT CONTROL MODULE - REMOVAL . 8W-97-6
FRONT CONTROL MODULE - REMOVAL....8E-5
FRONT CROSSMEMBER - INSTALLATION . . 13-22
FRONT CROSSMEMBER - REMOVAL.....13-22
FRONT DOOR GLASS RUN
WEATHERSTRIP - INSTALLATION........23-92
FRONT DOOR GLASS RUN
WEATHERSTRIP - REMOVAL............23-92
FRONT DOOR INNER BELT MOLDING -
INSTALLATION.......................23-93
FRONT DOOR INNER BELT MOLDING -
REMOVAL..........................23-93
FRONT DOOR OUTER BELT MOLDING -
INSTALLATION.......................23-93
FRONT DOOR OUTER BELT MOLDING -
REMOVAL..........................23-92
FRONT FASCIA - INSTALLATION..........13-3
FRONT FASCIA - REMOVAL..............13-2
FRONT FENDER - INSTALLATION........23-39
FRONT FENDER - REMOVAL............23-39
FRONT FRAME RAIL TIP REPLACEMENT
- STANDARD PROCEDURE, LIGHT
DUTY...............................13-4
FRONT HOSE - REMOVAL...............5-12
FRONT MOUNT - INSTALLATION . . . 9-147,9-218,
9-287,9-59
FRONT MOUNT - REMOVAL . . 9-146,9-217,9-286,
9-58
FRONT OUTBOARD SEAT BELT BUCKLE -
INSTALLATION......................8O-38
FRONT OUTBOARD SEAT BELT BUCKLE -
REMOVAL..........................8O-37
FRONT OUTPUT SHAFT SEAL -
INSTALLATION . . . 21-442,21-477,21-508,21-538,
21-572
FRONT OUTPUT SHAFT SEAL -
REMOVAL . 21-441,21-477,21-507,21-537,21-572
FRONT PARKING BRAKE CABLE -
INSTALLATION........................5-38
FRONT PARKING BRAKE CABLE -
REMOVAL
...........................5-36
FRONT SEAL - INSTALLATION, OIL
PUMP
............................21-391
FRONT SEAL - REMOVAL, OIL PUMP
....21-391
FRONT SERVO - ASSEMBLY
...........21-209
FRONT SERVO - CLEANING
...........21-209
DRINDEX 13
Description Group-Page Description Group-Page Description Group-Page

OUTER TIE ROD END - REMOVAL.......19-32
OUTLET - DESCRIPTION, CIGAR
LIGHTER.........................8W-97-2
OUTLET - DESCRIPTION, POWER......8W-97-7
OUTLET - DIAGNOSIS AND TESTING,
CIGAR LIGHTER...................8W-97-2
OUTLET - DIAGNOSIS AND TESTING,
POWER..........................8W-97-7
OUTLET - INSTALLATION, POWER.....8W-97-8
OUTLET - OPERATION, CIGAR LIGHTER . 8W-97-2
OUTLET - OPERATION, POWER.......8W-97-7
OUTLET - REMOVAL, POWER.........8W-97-8
OUTLETS - DESCRIPTION, AIR..........24-26
OUTLETS - INSTALLATION, AIR.........24-27
OUTLETS - REMOVAL, AIR.............24-26
OUTPUT - DESCRIPTION, PCM...........8I-5
OUTPUT - OPERATION, PCM............14-27
OUTPUT - OPERATION, PCM.............8I-5
OUTPUT SHAFT FRONT BEARING -
INSTALLATION......................21-216
OUTPUT SHAFT FRONT BEARING -
REMOVAL.........................21-216
OUTPUT SHAFT REAR BEARING -
INSTALLATION......................21-217
OUTPUT SHAFT REAR BEARING -
REMOVAL.........................21-216
OUTPUT SHAFT SEAL - INSTALLATION,
FRONT....21-442,21-477,21-508,21-538,21-572
OUTPUT SHAFT SEAL - REMOVAL,
FRONT.....21-441,21-477,21-507,21-537,21-572
OUTPUT SPEED SENSOR - DESCRIPTION . 21-391
OUTPUT SPEED SENSOR -
INSTALLATION......................21-392
OUTPUT SPEED SENSOR - OPERATION . . 21-391
OUTPUT SPEED SENSOR - REMOVAL . . . 21-391
OVERDRIVE CLUTCH - DESCRIPTION....21-217
OVERDRIVE CLUTCH - OPERATION.....21-217
OVERDRIVE ELECTRICAL CONTROLS -
DIAGNOSIS AND TESTING............21-262
OVERDRIVE SWITCH - DESCRIPTION,
TOW/HAUL..................21-261,21-392
OVERDRIVE SWITCH - INSTALLATION,
TOW/HAUL..................21-262,21-393
OVERDRIVE SWITCH - OPERATION,
TOW/HAUL..................21-262,21-392
OVERDRIVE SWITCH - REMOVAL,
TOW/HAUL..................21-262,21-392
OVERDRIVE UNIT - ASSEMBLY.........21-226
OVERDRIVE UNIT - CLEANING.........21-225
OVERDRIVE UNIT - DISASSEMBLY......21-218
OVERDRIVE UNIT - INSPECTION.......21-225
OVERDRIVE UNIT - INSTALLATION......21-235
OVERDRIVE UNIT - REMOVAL.........21-218
OVERFLOW VALVE - DESCRIPTION,
CASCADE...........................14-66
OVERFLOW VALVE - OPERATION,
CASCADE...........................14-66
OVERHEAD CONSOLE - DESCRIPTION....8M-1
OVERHEAD CONSOLE - DIAGNOSIS AND
TESTING............................8M-2
OVERHEAD CONSOLE - OPERATION......8M-2
OVERHEAD CONSOLE REMOVAL,
REMOVAL
...........................8M-6
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
ASSEMBLY
.........................21-237
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
CLEANING
.........................21-236
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
DESCRIPTION
......................21-236
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
DISASSEMBLY
......................21-236
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
INSPECTION
.......................21-237
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
OPERATION
........................21-236
OXYGEN SENSOR - DESCRIPTION
.......14-35
OXYGEN SENSOR - INSTALLATION
.......14-36
OXYGEN SENSOR - REMOVAL
..........14-35
PAINT CODE - DESCRIPTION
...........23-73
PAINT CODES - SPECIFICATIONS
........23-73
PAINT TOUCH-UP - DESCRIPTION
.......23-74PAINT TOUCH-UP - STANDARD
PROCEDURE........................23-74
PAN - CLEANING, OIL.............9-293,9-66
PAN - DESCRIPTION, OIL...............9-66
PAN - INSPECTION, OIL...........9-293,9-66
PAN - INSTALLATION, OIL . . . 9-155,9-224,9-293,
9-66
PAN - REMOVAL, OIL . . . 9-155,9-224,9-293,9-66
PANEL - INSTALLATION, TRIM.....23-24,23-33
PANEL - REMOVAL, TRIM.........23-24,23-33
PANEL ANTENNA CABLE -
INSTALLATION, INSTRUMENT............8A-7
PANEL ANTENNA CABLE - REMOVAL,
INSTRUMENT........................8A-7
PANEL ASSEMBLY - INSTALLATION,
INSTRUMENT.......................23-55
PANEL ASSEMBLY - REMOVAL,
INSTRUMENT.......................23-52
PANEL CENTER BEZEL - INSTALLATION,
INSTRUMENT.......................23-57
PANEL CENTER BEZEL - REMOVAL,
INSTRUMENT.......................23-57
PANEL DEMISTER DUCTS -
INSTALLATION, INSTRUMENT...........24-37
PANEL DEMISTER DUCTS - REMOVAL,
INSTRUMENT.......................24-36
PANEL DRIVER SIDE BEZEL -
INSTALLATION, INSTRUMENT...........23-58
PANEL DRIVER SIDE BEZEL - REMOVAL,
INSTRUMENT.......................23-58
PANEL DUCTS - INSTALLATION,
INSTRUMENT.........................24-37
PANEL DUCTS - REMOVAL,
INSTRUMENT.......................24-37
PANEL HEADLAMP SWITCH BEZEL -
INSTALLATION, INSTRUMENT...........23-56
PANEL HEADLAMP SWITCH BEZEL -
REMOVAL, INSTRUMENT..............23-56
PANEL LOWER SURROUND -
INSTALLATION, INSTRUMENT...........23-59
PANEL LOWER SURROUND - REMOVAL,
INSTRUMENT.......................23-59
PANEL REPAIR - STANDARD
PROCEDURE, PLASTIC BODY............23-3
PANEL TOP COVER - INSTALLATION,
INSTRUMENT.......................23-59
PANEL TOP COVER - REMOVAL,
INSTRUMENT.......................23-58
PANEL TRIM - INSTALLATION, REAR
CAB BACK..........................23-69
PANEL TRIM - REMOVAL, REAR CAB
BACK..............................23-68
PARK BRAKE CABLE - INSTALLATION,
REAR...............................5-38
PARK BRAKE CABLE - REMOVAL, REAR . . . 5-37
PARK LAMP RELAY - DESCRIPTION......8L-20
PARK LAMP RELAY - DIAGNOSIS AND
TESTING...........................8L-20
PARK LAMP RELAY - INSTALLATION.....8L-21
PARK LAMP RELAY - OPERATION.......8L-20
PARK LAMP RELAY - REMOVAL.........8L-21
PARKING BRAKE - DESCRIPTION.........5-36
PARKING BRAKE - OPERATION...........5-36
PARKING BRAKE CABLE -
INSTALLATION, FRONT.................5-38
PARKING BRAKE CABLE - REMOVAL,
FRONT..............................5-36
PARKING BRAKE SHOES - ADJUSTMENT
. . . 5-41
PARK/TURN SIGNAL LAMP -
INSTALLATION
.......................8L-21
PARK/TURN SIGNAL LAMP - REMOVAL
. . . 8L-21
PARTS - STANDARD PROCEDURES,
CLEANING FUEL SYSTEM
..............14-47
PASSENGER AIRBAG - DESCRIPTION
....8O-39
PASSENGER AIRBAG - INSTALLATION
....8O-41
PASSENGER AIRBAG - OPERATION
......8O-40
PASSENGER AIRBAG - REMOVAL
........8O-40
PASSENGER AIRBAG ON/OFF SWITCH -
DESCRIPTION
.......................8O-42
PASSENGER AIRBAG ON/OFF SWITCH -
INSTALLATION
......................8O-44
PASSENGER AIRBAG ON/OFF SWITCH -
OPERATION
.........................8O-43
PASSENGER AIRBAG ON/OFF SWITCH -
REMOVAL
..........................8O-43
PASSENGER SEAT SWITCH -
DESCRIPTION
.......................8N-15PASSENGER SEAT SWITCH - DIAGNOSIS
AND TESTING.......................8N-16
PASSENGER SEAT SWITCH -
INSTALLATION......................8N-16
PASSENGER SEAT SWITCH - OPERATION . 8N-15
PASSENGER SEAT SWITCH - REMOVAL . . . 8N-16
PATTERNS - DIAGNOSIS AND TESTING,
TIRE WEAR..........................22-8
PCM - DESCRIPTION...................8E-7
PCM - OPERATION...................8E-10
PCM INPUT - OPERATION, ASD SENSE.....8I-5
PCM OUTPUT - DESCRIPTION............8I-5
PCM OUTPUT - OPERATION............14-27
PCM OUTPUT - OPERATION.............8I-5
PCM/SKIM PROGRAMMING - STANDARD
PROCEDURE........................8E-14
PCV VALVE - 3.7L V-6/ 4.7L V-8 -
DIAGNOSIS AND TESTING.............25-20
PCV VALVE - DESCRIPTION............25-17
PCV VALVE - INSTALLATION............25-21
PCV VALVE - OPERATION..............25-19
PCV VALVE - REMOVAL...............25-21
PEDAL - DESCRIPTION.................5-28
PEDAL - INSTALLATION............5-28,5-42
PEDAL - INSTALLATION, ACCELERATOR . . . 14-21
PEDAL - OPERATION...................5-28
PEDAL - REMOVAL................5-28,5-42
PEDAL - REMOVAL, ACCELERATOR........14-21
PEDAL MOTOR - DESCRIPTION,
ADJUSTABLE..........................5-6
PEDAL MOTOR - INSTALLATION,
ADJUSTABLE..........................5-7
PEDAL MOTOR - REMOVAL,
ADJUSTABLE..........................5-7
PEDAL POSITION SENSOR -
DESCRIPTION, ACCELERATOR.....14-22,14-68
PEDAL POSITION SENSOR -
INSTALLATION, ACCELERATOR.....14-22,14-71
PEDAL POSITION SENSOR - OPERATION,
ACCELERATOR.................14-22,14-68
PEDAL POSITION SENSOR - REMOVAL,
ACCELERATOR.................14-22,14-68
PEDAL POSITION SWITCH -
DESCRIPTION, CLUTCH.................6-13
PEDAL POSITION SWITCH - DIAGNOSIS
AND TESTING, CLUTCH.................6-13
PEDAL POSITION SWITCH - OPERATION,
CLUTCH.............................6-13
PEDAL SWITCH - INSTALLATION,
ADJUSTABLE..........................5-6
PEDAL SWITCH - REMOVAL,
ADJUSTABLE..........................5-6
PER MILE, SPECIFICATIONS - TIRE
REVOLUTIONS.......................22-10
PERFORMANCE - DIAGNOSIS AND
TESTING, A/C........................24-3
PERFORMANCE - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS . . . 9-183,9-4,9-90
PERFORMANCE TEST - DIAGNOSIS AND
TESTING, HEATER.....................24-6
PILOT BEARING - INSTALLATION.........6-12
PILOT BEARING - REMOVAL.............6-11
PINION GEAR/RING GEAR -
INSTALLATION....................3-51,3-77
PINION GEAR/RING GEAR - REMOVAL . 3-49,3-75
PINION GEAR/RING GEAR/TONE RING -
INSTALLATION.............3-108,3-137,3-164
PINION GEAR/RING GEAR/TONE RING -
REMOVAL................3-106,3-134,3-162
PINION SEAL - INSTALLATION . 3-126,3-154,3-45,
3-71,3-96
PINION SEAL - REMOVAL....3-126,3-153,3-44,
3-70,3-95
PIPE - INSPECTION, EXHAUST.......11-7,11-8
PISTON & CONNECTING ROD -
CLEANING.....................9-140,9-212
PISTON & CONNECTING ROD -
DESCRIPTION.........9-139,9-211,9-281,9-48
PISTON & CONNECTING ROD -
INSPECTION
...................9-140,9-213
PISTON & CONNECTING ROD -
INSTALLATION
..................9-140,9-213
PISTON & CONNECTING ROD -
REMOVAL
................9-139,9-212,9-281
PISTON AND CONNECTING ROD -
CLEANING
..........................9-282
PISTON FITTING - STANDARD
PROCEDURE
...............9-139,9-211,9-51
DRINDEX 23
Description Group-Page Description Group-Page Description Group-Page

SENSOR - REMOVAL, LINE PRESSURE
(LP)..............................21-383
SENSOR - REMOVAL, MAP.............14-33
SENSOR - REMOVAL, OUTPUT SPEED . . . 21-391
SENSOR - REMOVAL, OXYGEN..........14-35
SENSOR - REMOVAL, POSITION . . 21-443,21-478
SENSOR - REMOVAL, REAR WHEEL
SPEED..............................5-48
SENSOR - REMOVAL, THROTTLE
POSITION..........................14-41
SENSOR - REMOVAL, TRANSMISSION
RANGE............................21-265
SENSOR - REMOVAL, WATER IN FUEL....14-66
SENSOR CIRCUIT - DIAGNOSIS AND
TESTING, AMBIENT TEMPERATURE......8M-10
SENSOR RETURN - DESCRIPTION.......8E-10
SENSOR (TRS) - DIAGNOSIS AND
TESTING, TRANSMISSION RANGE......21-264
SENSOR/MAP SENSOR - DESCRIPTION,
INTAKE AIR TEMPERATURE............14-82
SENSOR/MAP SENSOR - INSTALLATION,
INTAKE AIR TEMPERATURE............14-82
SENSOR/MAP SENSOR - OPERATION,
INTAKE AIR TEMPERATURE............14-82
SENSOR/MAP SENSOR - REMOVAL,
INTAKE AIR TEMPERATURE............14-82
SENSOR/PRESSURE SENSOR -
DESCRIPTION, INLET AIR
TEMPERATURE......................14-79
SENSOR/PRESSURE SENSOR -
INSTALLATION, INLET AIR
TEMPERATURE......................14-79
SENSOR/PRESSURE SENSOR -
OPERATION, INLET AIR TEMPERATURE . . . 14-79
SENSOR/PRESSURE SENSOR -
REMOVAL, INLET AIR TEMPERATURE....14-79
SENSOR/SWITCH - DESCRIPTION, OIL
PRESSURE..........................9-67
SENSOR/SWITCH - INSTALLATION, OIL
PRESSURE..........................9-67
SENSOR/SWITCH - OPERATION, OIL
PRESSURE..........................9-67
SENSOR/SWITCH - REMOVAL, OIL
PRESSURE..........................9-67
SENTRY KEY IMMOBILIZER MODULE -
DESCRIPTION.......................8E-13
SENTRY KEY IMMOBILIZER MODULE -
INSTALLATION.......................8E-15
SENTRY KEY IMMOBILIZER MODULE -
OPERATION.........................8E-13
SENTRY KEY IMMOBILIZER MODULE -
REMOVAL..........................8E-15
SENTRY KEY IMMOBILIZER MODULE
(SKIM) - DESCRIPTION................8Q-1
SENTRY KEY IMMOBILIZER MODULE
(SKIM) - OPERATION..................8Q-2
SENTRY KEY IMMOBILIZER SYSTEM
INDICATOR LAMP - DESCRIPTION........8Q-5
SENTRY KEY IMMOBILIZER SYSTEM
INDICATOR LAMP - OPERATION..........8Q-5
SENTRY KEY IMMOBILIZER SYSTEM
INITIALIZATION, STANDARD
PROCEDURE.........................8Q-3
SENTRY KEY IMMOBILIZER SYSTEM
(SKIS) - DESCRIPTION.................8Q-1
SENTRY KEY IMMOBILIZER SYSTEM
(SKIS) - OPERATION...................8Q-2
SENTRY KEY IMMOBILIZER SYSTEM
TRANSPONDER PROGRAMMING,
STANDARD PROCEDURE...............8Q-4
SEPARATOR - DESCRIPTION, FUEL
FILTER / WATER .....................14-50
SEPARATOR - INSTALLATION, FUEL
FILTER / WATER .....................14-50
SEPARATOR - OPERATION, FUEL FILTER
/ WATER ...........................14-50
SEPARATOR - REMOVAL, FUEL FILTER /
WATER.............................14-50
SERVO - ASSEMBLY, FRONT...........21-209
SERVO - ASSEMBLY, REAR............21-251
SERVO - CLEANING, FRONT...........21-209
SERVO - CLEANING, REAR............21-251
SERVO - DESCRIPTION.................8P-6
SERVO - DESCRIPTION, FRONT
........21-208
SERVO - DESCRIPTION, REAR
.........21-251
SERVO - DISASSEMBLY, FRONT
........21-209
SERVO - DISASSEMBLY, REAR
.........21-251
SERVO - INSPECTION, FRONT
.........21-209SERVO - INSTALLATION................8P-6
SERVO - OPERATION..................8P-6
SERVO - OPERATION, FRONT..........21-208
SERVO - OPERATION, REAR...........21-251
SERVO - REMOVAL....................8P-6
SETTING TRANSMITTER CODES -
STANDARD PROCEDURE..............8M-12
SHAFT - ASSEMBLY, PLANETARY
GEARTRAIN/OUTPUT.................21-244
SHAFT - CAUTION, HALF................3-20
SHAFT - DESCRIPTION, PLANETARY
GEARTRAIN/OUTPUT.................21-241
SHAFT - DIAGNOSIS AND TESTING,
HALF...............................3-20
SHAFT - DIAGNOSIS AND TESTING,
PROPELLER...........................3-1
SHAFT - DISASSEMBLY, PLANETARY
GEARTRAIN/OUTPUT.................21-242
SHAFT - HD FRONT - INSTALLATION,
PROPELLER...........................3-7
SHAFT - HD FRONT - REMOVAL,
PROPELLER...........................3-7
SHAFT - INSPECTION, PLANETARY
GEARTRAIN/OUTPUT.................21-243
SHAFT - INSTALLATION, BALANCE........9-80
SHAFT - INSTALLATION, HALF...........3-21
SHAFT - INSTALLATION, IDLER.....9-179,9-81
SHAFT - INSTALLATION, REAR
PROPELLER...........................3-8
SHAFT - OPERATION, PLANETARY
GEARTRAIN/OUTPUT..................21-241
SHAFT - REMOVAL, BALANCE...........9-80
SHAFT - REMOVAL, HALF...............3-20
SHAFT - REMOVAL, IDLER.........9-179,9-81
SHAFT - REMOVAL, REAR PROPELLER.....3-8
SHAFT - SPECIAL TOOLS, HALF..........3-21
SHAFT - SPECIAL TOOLS, PROPELLER.....3-6
SHAFT - SPECIFICATIONS, HALF..........3-21
SHAFT - SPECIFICATIONS, PROPELLER.....3-6
SHAFT - STANDARD PROCEDURE,
PROPELLER...........................3-3
SHAFT FRONT BEARING -
INSTALLATION, OUTPUT..............21-216
SHAFT FRONT BEARING - REMOVAL,
OUTPUT...........................21-216
SHAFT- LD FRONT - INSTALLATION,
PROPELLER...........................3-7
SHAFT- LD FRONT - REMOVAL,
PROPELLER...........................3-6
SHAFT REAR BEARING - INSTALLATION,
OUTPUT...........................21-217
SHAFT REAR BEARING - REMOVAL,
OUTPUT...........................21-216
SHAFT SEAL - INSTALLATION, FRONT
OUTPUT . . . 21-442,21-477,21-508,21-538,21-572
SHAFT SEAL - INSTALLATION, STEERING
GEAR INPUT........................19-29
SHAFT SEAL - REMOVAL, FRONT
OUTPUT . . . 21-441,21-477,21-507,21-537,21-572
SHAFT SEAL - REMOVAL, STEERING
GEAR INPUT........................19-27
SHAFT SEALS - INSTALLATION, AXLE . 3-43,3-70,
3-94
SHAFT SEALS - REMOVAL, AXLE . 3-43,3-69,3-94
SHAFTS - ASSEMBLY, AXLE.............3-69
SHAFTS - DISASSEMBLY, AXLE..........3-68
SHAFTS - INSTALLATION, AXLE....3-124,3-152,
3-43,3-69,3-94
SHAFTS - REMOVAL, AXLE . . . 3-124,3-152,3-43,
3-67,3-93
SHIELD - INSTALLATION, FRONT
WHEELHOUSE SPLASH................23-41
SHIELD - INSTALLATION, REAR
WHEELHOUSE SPLASH................23-41
SHIELD - REMOVAL, FRONT
WHEELHOUSE SPLASH................23-41
SHIELD - REMOVAL, REAR
WHEELHOUSE SPLASH................23-41
SHIELDS - DESCRIPTION, HEAT..........11-8
SHIELDS - INSTALLATION, HEAT.........11-8
SHIELDS - REMOVAL, HEAT.............11-8
SHIFT BOOT - INSTALLATION, 4WD
FLOOR
.............................23-62
SHIFT BOOT - REMOVAL, 4WD FLOOR
....23-62
SHIFT COVER - INSTALLATION
....21-129,21-87
SHIFT COVER - REMOVAL
.......21-129,21-87
SHIFT INTERLOCK - ADJUSTMENTS,
BRAKE TRANSMISSION
........21-196,21-365SHIFT INTERLOCK - DIAGNOSIS AND
TESTING, BRAKE TRANSMISSION......21-196,
21-364
SHIFT INTERLOCK SYSTEM -
DESCRIPTION, BRAKE TRANSMISSION . . 21-196,
21-364
SHIFT INTERLOCK SYSTEM -
OPERATION, BRAKE TRANSMISSION....21-196,
21-364
SHIFT LEVER - ADJUSTMENT....21-446,21-481
SHIFT LEVER - INSTALLATION . . . 21-445,21-480
SHIFT LEVER - INSTALLATION, GEAR.....19-12
SHIFT LEVER - REMOVAL.......21-444,21-479
SHIFT LEVER - REMOVAL, GEAR........19-12
SHIFT MECHANISM - DESCRIPTION....21-252,
21-398
SHIFT MECHANISM - INSTALLATION.....21-87
SHIFT MECHANISM - OPERATION......21-252,
21-398
SHIFT MECHANISM - REMOVAL.........21-86
SHIFT MOTOR - DESCRIPTION . . 21-511,21-541,
21-575
SHIFT MOTOR - INSTALLATION . . 21-511,21-541,
21-575
SHIFT MOTOR - OPERATION....21-511,21-541,
21-575
SHIFT MOTOR - REMOVAL.....21-511,21-541,
21-575
SHOCK - DIAGNOSIS AND TESTING . . . 2-24,2-38
SHOCK - DIAGNOSIS AND TESTING,
SPRING.............................2-41
SHOCK - INSTALLATION.............2-38,2-43
SHOCK - REMOVAL................2-38,2-43
SHOES - ADJUSTMENT, PARKING BRAKE . . 5-41
SHOES - INSTALLATION................5-40
SHOES - REMOVAL....................5-39
SIDE - INSTALLATION, LEFT............9-123
SIDE - INSTALLATION, RIGHT...........9-123
SIDE - REMOVAL, LEFT................9-122
SIDE - REMOVAL, RIGHT..............9-122
SIDE BEZEL - INSTALLATION,
INSTRUMENT PANEL DRIVER...........23-58
SIDE BEZEL - REMOVAL, INSTRUMENT
PANEL DRIVER......................23-58
SIDE CURTAIN AIRBAG - DESCRIPTION . . . 8O-56
SIDE CURTAIN AIRBAG - INSTALLATION . . 8O-58
SIDE CURTAIN AIRBAG - OPERATION....8O-56
SIDE CURTAIN AIRBAG - REMOVAL......8O-57
SIDE IMPACT SENSOR - DESCRIPTION . . . 8O-59
SIDE IMPACT SENSOR - OPERATION.....8O-59
SIDE MOLDINGS - INSTALLATION, BODY . . 23-36
SIDE MOLDINGS - REMOVAL, BODY.....23-36
SIDE VIEW MIRROR - INSTALLATION.....23-42
SIDE VIEW MIRROR - REMOVAL........23-41
SIDE VIEW MIRROR FLAG -
INSTALLATION.......................23-27
SIDE VIEW MIRROR FLAG - REMOVAL . . . 23-27
SIDE VIEW MIRROR GLASS -
INSTALLATION.......................23-43
SIDE VIEW MIRROR GLASS - REMOVAL . . 23-42
SIDEVIEW MIRROR - REMOVAL.........8N-12
SIGNAL INDICATOR - DESCRIPTION,
TURN..............................8J-40
SIGNAL INDICATOR - OPERATION, TURN . . 8J-41
SIGNAL LAMP - INSTALLATION,
PARK/TURN.........................8L-21
SIGNAL LAMP - REMOVAL, PARK/TURN . . 8L-21
SIGNAL SYSTEM - DESCRIPTION, TURN . . 8L-18
SIGNAL SYSTEM - OPERATION, TURN....8L-18
SILL TRIM COVER - INSTALLATION,
REAR DOOR........................23-71
SILL TRIM COVER - REMOVAL, REAR
DOOR.............................23-71
SIZE, SPARE WHEEL WITH MATCHING
TIRE - DESCRIPTION, FULL............22-15
SKID PLATE - INSTALLATION, FRONT.....13-23
SKID PLATE - INSTALLATION, TRANSFER
CASE..............................13-26
SKID PLATE - REMOVAL, FRONT........13-23
SKID PLATE - REMOVAL, TRANSFER
CASE..............................13-26
SLEEVE - INSTALLATION, HEADREST.....23-81
SLEEVE - REMOVAL, HEADREST
........23-81
SMOKE DIAGNOSIS CHARTS -
DIAGNOSIS AND TESTING
.............9-236
SNAP RINGS - ASSEMBLY, WITH
.........3-12
SNAP RINGS - DISASSEMBLY, WITH
......3-10
SOLENOID - DESCRIPTION
............21-252
30 INDEXDR
Description Group-Page Description Group-Page Description Group-Page