1998 DODGE RAM 1500 Vacuum leak

Check the vapor/vacuum lines at the LDP, LDP
filter and EVAP canister purge solenoid for
damage or leaks. If a leak is present, a Diagnos-
tic Trouble Code (DTC) may be set.
(4) Connect electrical connector to LDP.
ORVR
DESCRIPTION
The ORVR (On-Board Refueling Vapor Recovery)
system consists of a unique fuel tank, flow manage-
ment valve, fluid control valve, one-way check valve
and vapor canister.
OPERATION
The ORVR (On-Board Refueling Vapor Recovery)
system is used to remove excess fuel tank vapors.
This is done while the vehicle is being refueled.
Fuel flowing into the fuel filler tube (approx. 1º
I.D.) creates an aspiration effect drawing air into the
fuel fill tube. During refueling, the fuel tank is
vented to the EVAP canister to capture escaping
vapors. With air flowing into the filler tube, there are
no fuel vapors escaping to the atmosphere. Once the
refueling vapors are captured by the EVAP canister,
the vehicle's computer controlled purge system draws
vapor out of the canister for the engine to burn. The
vapor flow is metered by the purge solenoid so that
there is no, or minimal impact on driveability or
tailpipe emissions.
As fuel starts to flow through the fuel fill tube, it
opens the normally closed check valve and enters the
fuel tank. Vapor or air is expelled from the tank
through the control valve and on to the vapor canis-
ter. Vapor is absorbed in the EVAP canister until
vapor flow in the lines stops. This stoppage occurs
following fuel shut-off, or by having the fuel level in
the tank rise high enough to close the control valve.
This control valve contains a float that rises to seal
the large diameter vent path to the EVAP canister.
At this point in the refueling process, fuel tank pres-
sure increases, the check valve closes (preventing liq-
uid fuel from spiting back at the operator), and fuel
then rises up the fuel filler tube to shut off the dis-
pensing nozzle.
PCV VALVE
DESCRIPTION
3.7L V-6 / 4.7L V-8
The 3.7L V-6 and 4.7L V-8 engines are equipped
with a closed crankcase ventilation system and a
Positive Crankcase Ventilation (PCV) valve.
This system consists of:
²a PCV valve mounted to the oil filler housing
(Fig. 10). The PCV valve is sealed to the oil filler
housing with an o-ring.
²the air cleaner housing
²two interconnected breathers threaded into the
rear of each cylinder head (Fig. 11).
²tubes and hoses to connect the system compo-
nents.
Fig. 10 PCV VALVE - 3.7L V-6 / 4.7L V-8
1 - O-RING
2 - LOCATING TABS
3 - CAM LOCK
4 - OIL FILLER TUBE
5 - PCV LINE/HOSE
6 - P C V VA LV E
DREVAPORATIVE EMISSIONS 25 - 17
LEAK DETECTION PUMP (Continued)

5.7L V-8
(1) Clean out intake manifold opening.
(2) Check condition of 2 o-rings on PCV valve.
(3) Apply engine oil to 2 o-rings.
(4) Place PCV valve into intake manifold and
rotate 90 degrees clockwise for installation.
VACUUM LINES
DESCRIPTION
A vacuum schematic for emission related items can
be found on the vehicles VECI label. Refer to Vehicle
Emission Control Information (VECI) Label for label
location.
VAPOR CANISTER
DESCRIPTION
Two, maintenance free, EVAP canisters are used.
Both canisters are mounted into a two-piece support
bracket located near the front of the fuel tank (Fig.
23).
OPERATION
Two, maintenance free, EVAP canisters are
used.The EVAP canisters are filled with granules of
an activated carbon mixture. Fuel vapors entering
the EVAP canisters are absorbed by the charcoal
granules.
Fuel tank pressure vents into the EVAP canisters.
Fuel vapors are temporarily held in the canisters
until they can be drawn into the intake manifold.
The duty cycle EVAP canister purge solenoid allows
the EVAP canisters to be purged at predetermined
times and at certain engine operating conditions.
REMOVAL
Two, maintenance free, EVAP canisters are used.
Both canisters are mounted into a two-piece support
bracket located near the front of the fuel tank (Fig.
23).
(1) Raise and support vehicle.
(2) Remove fuel tubes/lines at each EVAP canister.
Note location of tubes/lines before removal for easier
installation.
(3) Remove lower support bracket (Fig. 24).
(4) Remove mounting nuts at top of each canister
(Fig. 24).
(5) Remove each canister from upper support
bracket.
INSTALLATION
(1) Place each canister into upper support bracket
and install nuts. Refer to Torque Specifications.
(2) Install lower support bracket. Refer to Torque
Specifications.
(3) Carefully install vapor/vacuum lines.The
vapor/vacuum lines and hoses must be firmly
connected. Also check the vapor/vacuum lines
at the LDP, LDP filter and EVAP canister purge
solenoid for damage or leaks. If a leak is
present, a Diagnostic Trouble Code (DTC) may
be set.
Fig. 23 LOCATION, EVAP CANISTERS
1 - LDP
2 - LDP MOUNTING BOLT
3 - ELEC. CONNEC.
4 - FILTER MOUNTING BOLT
5 - LDP FILTER
6 - CONNECTING HOSE
7 - EVAP CANISTER MOUNTING BRACKET
8 - EVAP CANISTERS (2)
25 - 22 EVAPORATIVE EMISSIONSDR
PCV VALVE (Continued)

NATURAL VAC LEAK
DETECTION ASSY
DESCRIPTION
Vehicles equipped with NGC engine control mod-
ules use an NVLD pump and system.Vehicles
equipped with JTEC engine control modules use an
LDP (leak detection pump). Refer to Leak Detection
Pump (LDP) for additional information.
The NVLD pump is located in the same area as the
leak detection pump. Refer to NVLD Removal /
Installation for additional information.
OPERATION
Vehicles equipped with NGC engine control mod-
ules use an NVLD pump and system.Vehicles
equipped with JTEC engine control modules use a
leak detection pump. Refer to Leak Detection Pump
(LDP) for additional information.
The Natural Vacuum Leak Detection (NVLD) sys-
tem is the next generation evaporative leak detection
system that will first be used on vehicles equipped
with the Next Generation Controller (NGC). This
new system replaces the leak detection pump as the
method of evaporative system leak detection. This isto detect a leak equivalent to a 0.0209(0.5 mm) hole.
This system has the capability to detect holes of this
size very dependably.
The basic leak detection theory employed with
NVLD is the9Gas Law9. This is to say that the pres-
sure in a sealed vessel will change if the temperature
of the gas in the vessel changes. The vessel will only
see this effect if it is indeed sealed. Even small leaks
will allow the pressure in the vessel to come to equi-
librium with the ambient pressure. In addition to the
detection of very small leaks, this system has the
capability of detecting medium as well as large evap-
orative system leaks.
A vent valve seals the canister vent during engine
off conditions. If the vapor system has a leak of less
than the failure threshold, the evaporative system
will be pulled into a vacuum, either due to the cool
down from operating temperature or diurnal ambient
temperature cycling. The diurnal effect is considered
one of the primary contributors to the leak determi-
nation by this diagnostic. When the vacuum in the
system exceeds about 19H2O (0.25 KPA), a vacuum
switch closes. The switch closure sends a signal to
the NGC. The NGC, via appropriate logic strategies,
utilizes the switch signal, or lack thereof, to make a
determination of whether a leak is present.
Fig. 24 EVAP CANISTERS - REMOVAL / INSTALLATION
1 - CANISTER MOUNTING NUTS
2 - CONNECTING HOSE
3 - UPPER SUPPORT BRACKET4 - LOWER SUPPORT BRACKET
5 - OUTER CANISTER
6 - INNER CANISTER
DREVAPORATIVE EMISSIONS 25 - 23
VAPOR CANISTER (Continued)

The NVLD device is designed with a normally open
vacuum switch, a normally closed solenoid, and a
seal, which is actuated by both the solenoid and a
diaphragm. The NVLD is located on the atmospheric
vent side of the canister. The NVLD assembly may
be mounted on top of the canister outlet, or in-line
between the canister and atmospheric vent filter. The
normally open vacuum switch will close with about 19
H2O (0.25 KPA) vacuum in the evaporative system.
The diaphragm actuates the switch. This is above the
opening point of the fuel inlet check valve in the fill
tube so cap off leaks can be detected. Submerged fill
systems must have recirculation lines that do not
have the in-line normally closed check valve that pro-
tects the system from failed nozzle liquid ingestion,
in order to detect cap off conditions.
The normally closed valve in the NVLD is intended
to maintain the seal on the evaporative system dur-
ing the engine off condition. If vacuum in the evapo-
rative system exceeds 39to 69H2O (0.75 to 1.5 KPA),
the valve will be pulled off the seat, opening the seal.
This will protect the system from excessive vacuum
as well as allowing sufficient purge flow in the event
that the solenoid was to become inoperative.
The solenoid actuates the valve to unseal the can-
ister vent while the engine is running. It also will be
used to close the vent during the medium and large
leak tests and during the purge flow check. This sole-
noid requires initial 1.5 amps of current to pull the
valve open but after 100 ms. will be duty cycled down
to an average of about 150 mA for the remainder of
the drive cycle.
Another feature in the device is a diaphragm that
will open the seal in the NVLD with pressure in the
evaporative system. The device will9blow off9at
about 0.59H2O (0.12 KPA) pressure to permit the
venting of vapors during refueling. An added benefit
to this is that it will also allow the tank to9breathe9
during increasing temperatures, thus limiting the
pressure in the tank to this low level. This is benefi-
cial because the induced vacuum during a subse-
quent declining temperature will achieve the switch
closed (pass threshold) sooner than if the tank had to
decay from a built up pressure.
The device itself has 3 wires: Switch sense, sole-
noid driver and ground. It also includes a resistor to
protect the switch from a short to battery or a short
to ground. The NGC utilizes a high-side driver to
energize and duty-cycle the solenoid.REMOVAL
The NVLD pump and filter are attached to the
front of the EVAP canister mounting bracket (Fig.
25). This is located near the front of the fuel tank.
The pump and filter are replaced (serviced) as one
unit.
(1) Raise and support vehicle.
(2) Carefully remove pump hose clamp and hose at
filter.
(3) Carefully remove other vapor/vacuum hose at
pump.
(4) Disconnect 3±way electrical connector at pump.
(5) The NVLD pump snaps onto the EVAP canister
mounting bracket. Press on release tab (Fig. 26)
while sliding pump from bracket.
Fig. 25 NVLD PUMP LOCATION
1 - EVAP CANISTER MOUNTING BRACKET
2 - NVLD PUMP
3 - FILTER
25 - 24 EVAPORATIVE EMISSIONSDR
NATURAL VAC LEAK DETECTION ASSY (Continued)

INSTALLATION
(1) Install NVLD pump to EVAP canister mount-
ing bracket (snaps on).
(2) Install NVLD filter and bolt to EVAP canister
mounting bracket. Refer to Torque Specifications.
(3) Carefully install vapor/vacuum lines to NVLD
pump, and install hose to filter.The vapor/vacuum
lines and hoses must be firmly connected.
Check the vapor/vacuum lines at the NVLD
pump, filter and EVAP canister purge solenoid
for damage or leaks. If a leak is present, a Diag-
nostic Trouble Code (DTC) may be set.
(4) Connect 3±way electrical connector to pump.
Fig. 26 REMOVE / INSTALL NVLD PUMP
1 - NVLD PUMP
2 - RELEASE TAB
DREVAPORATIVE EMISSIONS 25 - 25
NATURAL VAC LEAK DETECTION ASSY (Continued)

LATCH STRIKER - INSTALLATION . . 23-17,23-23,
23-33
LATCH STRIKER - REMOVAL . 23-16,23-23,23-33
LATCH STRIKER / SECONDARY CATCH -
INSTALLATION.......................23-48
LATCH STRIKER / SECONDARY CATCH -
REMOVAL..........................23-47
LD & HD EXCEPT 4X4 HD -
INSTALLATION, ALL..................19-14
LD & HD EXCEPT 4X4 HD - REMOVAL,
ALL ...............................19-14
LD FRONT - INSTALLATION, PROPELLER
SHAFT...............................3-7
LD FRONT - REMOVAL, PROPELLER
SHAFT...............................3-6
LEAD - DIAGNOSIS AND TESTING,
TIRE/VEHICLE........................22-8
LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING FLUID....21-144,21-318
LEAK - DIAGNOSIS AND TESTING,
ENGINE OIL................9-152,9-220,9-64
LEAK DETECTION ASSY - DESCRIPTION,
NATURAL VAC.......................25-23
LEAK DETECTION ASSY - INSTALLATION,
NATURAL VAC.......................25-25
LEAK DETECTION ASSY - OPERATION,
NATURAL VAC.......................25-23
LEAK DETECTION ASSY - REMOVAL,
NATURAL VAC.......................25-24
LEAK DETECTION PUMP - DESCRIPTION . . 25-13
LEAK DETECTION PUMP - INSTALLATION . 25-16
LEAK DETECTION PUMP - OPERATION....25-14
LEAK DETECTION PUMP - REMOVAL.....25-16
LEAKAGE - DIAGNOSIS AND TESTING,
CYLINDER COMBUSTION PRESSURE . 9-186,9-8,
9-93
LEAKAGE - DIAGNOSIS AND TESTING,
INTAKE MANIFOLD..............9-159,9-225
LEAKAGE - DIAGNOSIS AND TESTING,
PUMP.............................19-40
LEAKS - DIAGNOSIS AND TESTING,
CHARGE AIR COOLER SYSTEM.........11-16
LEAKS - DIAGNOSIS AND TESTING,
COOLING SYSTEM - TESTING.............7-5
LEAKS - DIAGNOSIS AND TESTING,
HIGH-PRESSURE FUEL LINE............14-58
LEAKS - DIAGNOSIS AND TESTING,
INTAKE MANIFOLD....................9-72
LEAKS - DIAGNOSIS AND TESTING,
REAR SEAL AREA...........9-137,9-209,9-65
LEAKS - DIAGNOSIS AND TESTING,
REFRIGERANT SYSTEM...............24-44
LEAKS - DIAGNOSIS AND TESTING,
WATER .............................23-1
LEAKS - STANDARD PROCEDURE,
REPAIRING.........................22-10
LEARN - STANDARD PROCEDURE,
DRIVE.............................8E-23
LEARN - STANDARD PROCEDURE, TCM
QUICK.............................8E-23
LEFT CYLINDER HEAD - INSTALLATION . . . 9-112
LEFT CYLINDER HEAD - REMOVAL.......9-108
LEFT REAR CABLE - INSTALLATION.......5-39
LEFT REAR CABLE - REMOVAL...........5-38
LENS REPLACEMENT - STANDARD
PROCEDURE, MODULE................8M-3
LEVEL - DIAGNOSIS AND TESTING,
EFFECTS OF INCORRECT FLUID . . 21-201,21-366
LEVEL - STANDARD PROCEDURE,
BRAKE FLUID........................5-23
LEVEL - STANDARD PROCEDURE,
ENGINE OIL.........................9-292
LEVEL - STANDARD PROCEDURE,
REFRIGERANT OIL...................24-69
LEVEL CHECK - STANDARD
PROCEDURE, COOLANT................7-17
LEVEL CHECK - STANDARD
PROCEDURE, FLUID...........21-202,21-366
LEVEL CHECKING - STANDARD
PROCEDURE, POWER STEERING FLUID
. . . 19-43
LEVEL SENDING UNIT / SENSOR -
DESCRIPTION, FUEL
..............14-57,14-6
LEVEL SENDING UNIT / SENSOR -
INSTALLATION, FUEL
..................14-7
LEVEL SENDING UNIT / SENSOR -
OPERATION, FUEL
................14-57,14-6
LEVEL SENDING UNIT / SENSOR -
REMOVAL, FUEL
......................14-7LEVEL SWITCH - DESCRIPTION,
WASHER FLUID......................8R-9
LEVEL SWITCH - INSTALLATION,
WASHER FLUID.....................8R-11
LEVEL SWITCH - OPERATION, WASHER
FLUID..............................8R-9
LEVEL SWITCH - REMOVAL, WASHER
FLUID.............................8R-10
LEVER - ADJUSTMENT, SHIFT . . . 21-446,21-481
LEVER - INSTALLATION, GEAR SHIFT.....19-12
LEVER - INSTALLATION, SHIFT . . . 21-445,21-480
LEVER - REMOVAL, GEAR SHIFT........19-12
LEVER - REMOVAL, SHIFT......21-444,21-479
LEVER KNOB RELEASE - INSTALLATION,
TILT ...............................19-16
LEVER KNOB RELEASE - REMOVAL, TILT . . 19-16
LICENSE PLATE LAMP - INSTALLATION . . . 8L-17
LICENSE PLATE LAMP - REMOVAL.......8L-17
LICENSE PLATE LAMP UNIT -
INSTALLATION.......................8L-17
LICENSE PLATE LAMP UNIT - REMOVAL . . 8L-17
LID - INSTALLATION, CENTER SEAT
BACK..............................23-79
LID - INSTALLATION, UNDER SEAT
STORAGE BIN.......................23-80
LID - REMOVAL, CENTER SEAT BACK....23-79
LID - REMOVAL, UNDER SEAT STORAGE
BIN ...............................23-80
LIFTERS/TAPPETS - CLEANING, SOLID....9-279
LIFTERS/TAPPETS - INSPECTION, SOLID . . . 9-279
LIFTERS/TAPPETS - INSTALLATION,
SOLID.............................9-280
LIFTERS/TAPPETS - REMOVAL, SOLID....9-279
LIGHT DUTY FRONT FRAME RAIL TIP
REPLACEMENT - STANDARD
PROCEDURE.........................13-4
LIGHTER OUTLET - DESCRIPTION,
CIGAR...........................8W-97-2
LIGHTER OUTLET - DIAGNOSIS AND
TESTING, CIGAR...................8W-97-2
LIGHTER OUTLET - OPERATION, CIGAR . 8W-97-2
LIMITING VALVE - DESCRIPTION, FUEL
PRESSURE.........................14-61
LIMITING VALVE - INSTALLATION, FUEL
PRESSURE.........................14-61
LIMITING VALVE - OPERATION, FUEL
PRESSURE.........................14-61
LIMITING VALVE - REMOVAL, FUEL
PRESSURE.........................14-61
LINE - DESCRIPTION, A/C DISCHARGE....24-56
LINE - DESCRIPTION, LIQUID...........24-65
LINE - DESCRIPTION, REFRIGERANT.....24-42
LINE - DESCRIPTION, SUCTION.........24-70
LINE - INSTALLATION, LIQUID..........24-66
LINE - REMOVAL, LIQUID..............24-65
LINE AND TERMINAL REPAIR -
STANDARD PROCEDURE, GRID..........8G-4
LINE COUPLER - DESCRIPTION,
REFRIGERANT.......................24-67
LINE COUPLER - INSTALLATION,
REFRIGERANT.......................24-68
LINE COUPLER - OPERATION,
REFRIGERANT.......................24-67
LINE COUPLER - REMOVAL,
REFRIGERANT.......................24-68
LINE LEAKS - DIAGNOSIS AND TESTING,
HIGH-PRESSURE FUEL................14-58
LINE PRESSURE (LP) SENSOR -
DESCRIPTION......................21-382
LINE PRESSURE (LP) SENSOR -
INSTALLATION......................21-383
LINE PRESSURE (LP) SENSOR -
OPERATION........................21-383
LINE PRESSURE (LP) SENSOR -
REMOVAL.........................21-383
LINES - DESCRIPTION, FUEL.......14-57,14-7
LINES - DESCRIPTION, VACUUM........25-22
LINES - INSTALLATION, FUEL...........14-60
LINES - OPERATION, FUEL.............14-57
LINES - OPERATION, REFRIGERANT......24-42
LINES - REMOVAL, FUEL..............14-58
LINK - INSTALLATION, DRAG...........19-36
LINK - REMOVAL, DRAG...............19-36
LINK CONNECTOR - DESCRIPTION, DATA
. . 8E-3
LINK CONNECTOR - OPERATION, DATA
....8E-3
LINKAGE - INSTALLATION
...............6-12
LINKAGE - LINK/COIL - DESCRIPTION
....19-34
LINKAGE - REMOVAL
..................6-12LINKAGE, SPECIAL TOOLS - STEERING . . . 19-35
LINK/COIL - DESCRIPTION, GEAR........19-20
LINK/COIL - DESCRIPTION, LINKAGE.....19-34
LINK/COIL - INSTALLATION, GEAR.......19-21
LINK/COIL - OPERATION, GEAR.........19-20
LINK/COIL - REMOVAL, GEAR...........19-20
LINK/COIL SUSPENSION - STANDARD
PROCEDURE, ALIGNMENT...............2-5
LIQUID LINE - DESCRIPTION...........24-65
LIQUID LINE - INSTALLATION...........24-66
LIQUID LINE - REMOVAL..............24-65
LOAD FLOOR - INSTALLATION..........23-72
LOAD FLOOR - REMOVAL..............23-71
LOAD FLOOR SUPPORT CYLINDER -
INSTALLATION.......................23-72
LOAD FLOOR SUPPORT CYLINDER -
REMOVAL..........................23-72
LOCATION - DESCRIPTION, CONNECTOR/
GROUND/SPLICE...................8W-91-1
LOCATIONS - SPECIFICATIONS, SEALER . 23-102
LOCATIONS - SPECIFICATIONS,
STRUCTURAL ADHESIVE..............23-112
LOCATIONS - SPECIFICATIONS, WELD . . . 23-120
LOCK - STANDARD PROCEDURE,
HYDROSTATIC..................9-190,9-240
LOCK CYLINDER - DIAGNOSIS AND
TESTING, IGNITION SWITCH AND KEY....19-11
LOCK CYLINDER - INSTALLATION.......23-24
LOCK CYLINDER - REMOVAL.............23-24
LOCK MOTOR - DESCRIPTION, DOOR.....8N-4
LOCK MOTOR - DIAGNOSIS AND
TESTING, DOOR......................8N-4
LOCK MOTOR - OPERATION, DOOR.......8N-4
LOCK SWITCH - DIAGNOSIS AND
TESTING, POWER.....................8N-4
LOCK SWITCH - INSTALLATION, POWER . . . 8N-4
LOCK SWITCH - REMOVAL, POWER......8N-4
LOCKING RETRACTOR - DESCRIPTION,
AUTOMATIC........................8O-14
LOCKING RETRACTOR - OPERATION,
AUTOMATIC........................8O-14
LOCKS - DESCRIPTION, POWER.........8N-1
LOCKS - DIAGNOSIS AND TESTING,
POWER.............................8N-3
LOCKS - OPERATION, POWER...........8N-2
LOOP ADJUSTER - INSTALLATION, SEAT
BELT TURNING......................8O-55
LOOP ADJUSTER - REMOVAL, SEAT
BELT TURNING......................8O-55
LOOP BRACKETS - INSTALLATION, SEAT
BACK REAR - FOOTMANS..............23-85
LOOP BRACKETS - REMOVAL, SEAT
BACK REAR - FOOTMANS..............23-85
LOW FUEL INDICATOR - DESCRIPTION . . . 8J-30
LOW FUEL INDICATOR - OPERATION.....8J-30
LOWER BALL JOINT - DIAGNOSIS AND
TESTING........................2-19,2-34
LOWER BALL JOINT - INSTALLATION . 2-20,2-35
LOWER BALL JOINT - REMOVAL.....2-19,2-35
LOWER CONTROL ARM BUSHINGS -
2WD (LD) - INSTALLATION..............2-15
LOWER CONTROL ARM BUSHINGS -
2WD (LD) - REMOVAL.................2-13
LOWER CONTROL ARM BUSHINGS -
4WD (LD) - INSTALLATION..............2-14
LOWER CONTROL ARM BUSHINGS -
4WD (LD) - REMOVAL.................2-13
LOWER SURROUND - INSTALLATION,
INSTRUMENT PANEL..................23-59
LOWER SURROUND - REMOVAL,
INSTRUMENT PANEL..................23-59
LOWER SUSPENSION ARM -
INSTALLATION........................2-38
LOWER SUSPENSION ARM - REMOVAL....2-38
LOWER TRIM - INSTALLATION,
B-PILLAR...........................23-64
LOWER TRIM - INSTALLATION,
C-PILLAR...........................23-67
LOWER TRIM - REMOVAL, B-PILLAR.....23-63
LOWER TRIM - REMOVAL, C-PILLAR.....23-66
LOW/REVERSE CLUTCH - ASSEMBLY....21-385
LOW/REVERSE CLUTCH - CLEANING
....21-385
LOW/REVERSE CLUTCH - DISASSEMBLY
. 21-384
LOW/REVERSE CLUTCH - INSPECTION
. . 21-385
LUBRICANTS - DESCRIPTION, ENGINE
OIL
.................................0-1
LUBRICATION - DESCRIPTION
.....9-150,9-220,
9-289,9-61
DRINDEX 19
Description Group-Page Description Group-Page Description Group-Page

RELAY - DESCRIPTION, STARTER
MOTOR............................8F-35
RELAY - DESCRIPTION, TRANSMISSION
CONTROL.........................21-405
RELAY - DESCRIPTION, WIPER
HIGH/LOW..........................8R-20
RELAY - DESCRIPTION, WIPER ON/OFF . . . 8R-24
RELAY - DIAGNOSIS AND TESTING,
PARK LAMP.........................8L-20
RELAY - DIAGNOSIS AND TESTING,
STARTER ...........................8F-36
RELAY - DIAGNOSIS AND TESTING,
WIPER HIGH/LOW...................8R-21
RELAY - DIAGNOSIS AND TESTING,
WIPER ON/OFF......................8R-25
RELAY - INSTALLATION, A/C
COMPRESSOR CLUTCH...............24-14
RELAY - INSTALLATION, FOG LAMP......8L-13
RELAY - INSTALLATION, FUEL HEATER . . . 14-53
RELAY - INSTALLATION, FUEL PUMP.....14-28
RELAY - INSTALLATION, INTAKE AIR
HEATER ............................14-82
RELAY - INSTALLATION, PARK LAMP.....8L-21
RELAY - INSTALLATION, REAR WINDOW
DEFOGGER..........................8G-4
RELAY - INSTALLATION, STARTER
MOTOR............................8F-37
RELAY - INSTALLATION, WIPER
HIGH/LOW..........................8R-22
RELAY - INSTALLATION, WIPER ON/OFF . . 8R-26
RELAY - OPERATION, A/C COMPRESSOR
CLUTCH.............................24-13
RELAY - OPERATION, FOG LAMP........8L-13
RELAY - OPERATION, FUEL HEATER......14-52
RELAY - OPERATION, FUEL PUMP.......14-27
RELAY - OPERATION, INTAKE AIR
HEATER ............................14-82
RELAY - OPERATION, PARK LAMP.......8L-20
RELAY - OPERATION, REAR WINDOW
DEFOGGER..........................8G-3
RELAY - OPERATION, STARTER MOTOR . . . 8F-36
RELAY - OPERATION, TRANSMISSION
CONTROL.........................21-405
RELAY - OPERATION, WIPER HIGH/LOW . . 8R-20
RELAY - OPERATION, WIPER ON/OFF....8R-25
RELAY - REMOVAL, A/C COMPRESSOR
CLUTCH............................24-14
RELAY - REMOVAL, FOG LAMP.........8L-13
RELAY - REMOVAL, FUEL HEATER.......14-52
RELAY - REMOVAL, FUEL PUMP........14-28
RELAY - REMOVAL, INTAKE AIR HEATER . . 14-82
RELAY - REMOVAL, PARK LAMP........8L-21
RELAY - REMOVAL, REAR WINDOW
DEFOGGER..........................8G-3
RELAY - REMOVAL, STARTER MOTOR....8F-37
RELAY - REMOVAL, WIPER HIGH/LOW . . . 8R-21
RELAY - REMOVAL, WIPER ON/OFF......8R-26
RELAYS - DIAGNOSIS AND TESTING,
ASD AND FUEL PUMP..................8I-5
RELEASE - INSTALLATION, TILT LEVER
KNOB..............................19-16
RELEASE - REMOVAL, TILT LEVER KNOB . . 19-16
RELEASE - STANDARD PROCEDURE,
FUEL SYSTEM PRESSURE..............14-2
RELEASE BEARING - INSTALLATION,
CLUTCH
.............................6-10
RELEASE BEARING - REMOVAL, CLUTCH
...6-9
RELEASE CABLE/HANDLE ASSEMBLY -
INSTALLATION, LATCH
................23-47
RELEASE CABLE/HANDLE ASSEMBLY -
REMOVAL, LATCH
....................23-47
RELEASE HANDLE - INSTALLATION
.......5-44
RELEASE HANDLE - REMOVAL
...........5-44
RELEASE HANDLE/LATCH REMOTE -
INSTALLATION
.......................23-17
RELEASE HANDLE/LATCH REMOTE -
REMOVAL
..........................23-17
RELIEF VALVE - CLEANING, OIL
PRESSURE
.........................9-294
RELIEF VALVE - DESCRIPTION, HIGH
PRESSURE
.........................24-48
RELIEF VALVE - INSPECTION, OIL
PRESSURE
.........................9-294
RELIEF VALVE - INSTALLATION, OIL
PRESSURE
.........................9-294
RELIEF VALVE - OPERATION, HIGH
PRESSURE
.........................24-48RELIEF VALVE - REMOVAL, OIL
PRESSURE.........................9-294
REMINDER PROGRAMMING -
STANDARD PROCEDURE, ENHANCED
SEATBELT..........................8J-35
REMOTE - INSTALLATION, RELEASE
HANDLE/LATCH......................23-17
REMOTE - REMOVAL, RELEASE
HANDLE/LATCH......................23-17
REMOTE KEYLESS ENTRY MODULE -
DESCRIPTION........................8N-7
REMOTE KEYLESS ENTRY MODULE -
DIAGNOSIS AND TESTING..............8N-7
REMOTE KEYLESS ENTRY MODULE -
INSTALLATION.......................8N-8
REMOTE KEYLESS ENTRY MODULE -
OPERATION..........................8N-7
REMOTE KEYLESS ENTRY MODULE -
REMOVAL...........................8N-7
REMOTE KEYLESS ENTRY
TRANSMITTER - DIAGNOSIS AND
TESTING............................8N-8
REMOTE KEYLESS ENTRY
TRANSMITTER - SPECIFICATIONS........8N-9
REMOTE SWITCHES - DESCRIPTION.....8A-10
REMOTE SWITCHES - DIAGNOSIS AND
TESTING...........................8A-11
REMOTE SWITCHES - INSTALLATION.....8A-12
REMOTE SWITCHES - OPERATION.......8A-11
REMOTE SWITCHES - REMOVAL........8A-12
REMOVAL/INSTALLATION, REMOVAL.....25-13
REMOVAL/INSTALLATION, REMOVAL.....14-52,
14-57,14-66
REPAIR - DESCRIPTION, THREADED
HOLE.............................Intro.-8
REPAIR - STANDARD PROCEDURE,
ALUMINUM THREAD...........21-158,21-318
REPAIR - STANDARD PROCEDURE, CAM
BORE..............................9-267
REPAIR - STANDARD PROCEDURE,
CYLINDER BORE.....................9-265
REPAIR - STANDARD PROCEDURE, GRID
LINE AND TERMINAL..................8G-4
REPAIR - STANDARD PROCEDURE,
HYDROFORM FENDER RAIL............13-11
REPAIR - STANDARD PROCEDURE,
PLASTIC BODY PANEL.................23-3
REPAIR DAMAGED OR WORN THREADS
- STANDARD PROCEDURE . 9-190,9-240,9-9,9-94
REPAIRING LEAKS - STANDARD
PROCEDURE........................22-10
REQUIREMENTS - DESCRIPTION,
ENGINE COOLING SYSTEM..............24-1
REQUIREMENTS - DIESEL ENGINE -
DESCRIPTION, FUEL....................0-1
RESERVOIR - DESCRIPTION, VACUUM....8P-9
RESERVOIR - DESCRIPTION, WASHER . . . 8R-14
RESERVOIR - DIAGNOSIS AND TESTING,
VACUUM............................8P-9
RESERVOIR - INSTALLATION...........19-47
RESERVOIR - INSTALLATION, FLUID......5-24
RESERVOIR - INSTALLATION, VACUUM . . . 8P-10
RESERVOIR - OPERATION, VACUUM......8P-9
RESERVOIR - OPERATION, WASHER.....8R-15
RESERVOIR - REMOVAL...............19-47
RESERVOIR - REMOVAL, FLUID..........5-23
RESERVOIR - REMOVAL, VACUUM........8P-9
RESERVOIR TO COOLER -
INSTALLATION, RETURN HOSE.....19-44,19-45
RESERVOIR TO COOLER - REMOVAL,
RETURN HOSE.................19-44,19-45
RESISTANCE, 3.7L V-6 - IGNITION COIL....8I-5
RESISTANCE, 4.7L V-8 - IGNITION COIL....8I-5
RESISTANCE, 5.7L V-8 - IGNITION COIL....8I-5
RESISTANCE, SPECIFICATIONS - SPARK
PLUG CABLE.........................8I-4
RESISTOR BLOCK - DESCRIPTION,
BLOWER MOTOR....................24-18
RESISTOR BLOCK - DIAGNOSIS AND
TESTING, BLOWER MOTOR
............24-19
RESISTOR BLOCK - INSTALLATION,
BLOWER MOTOR
....................24-19
RESISTOR BLOCK - OPERATION,
BLOWER MOTOR
....................24-18
RESISTOR BLOCK - REMOVAL, BLOWER
MOTOR
............................24-19
RESTRAINT ANCHOR - DESCRIPTION,
CHILD
.............................8O-15RESTRAINT ANCHOR - INSTALLATION,
CHILD.............................8O-18
RESTRAINT ANCHOR - OPERATION,
CHILD.............................8O-17
RESTRAINT ANCHOR - REMOVAL, CHILD . 8O-17
RESTRAINT DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER A
SUPPLEMENTAL......................8O-7
RESTRAINT SYSTEM - DIAGNOSIS AND
TESTING, SUPPLEMENTAL..............8O-6
RESTRAINT SYSTEM - WARNINGS.......8O-5
RESTRAINTS - DESCRIPTION............8O-2
RESTRAINTS - OPERATION.............8O-4
RESTRAINTS - STANDARD PROCEDURE,
HANDLING NON-DEPLOYED
SUPPLEMENTAL......................8O-6
RETAINER - ASSEMBLY, OVERRUNNING
CLUTCH CAM/OVERDRIVE PISTON......21-237
RETAINER - CLEANING, OVERRUNNING
CLUTCH CAM/OVERDRIVE PISTON......21-236
RETAINER - DESCRIPTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON.................21-236
RETAINER - DISASSEMBLY,
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON.................21-236
RETAINER - INSPECTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON.................21-237
RETAINER - INSTALLATION, A-PILLAR
WEATHERSTRIP.....................23-91
RETAINER - INSTALLATION,
CRANKSHAFT REAR OIL SEAL.....9-210,9-277
RETAINER - INSTALLATION, DRIP RAIL
WEATHERSTRIP.....................23-92
RETAINER - OPERATION, OVERRUNNING
CLUTCH CAM/OVERDRIVE PISTON......21-236
RETAINER - REMOVAL, A-PILLAR
WEATHERSTRIP.....................23-91
RETAINER - REMOVAL, CRANKSHAFT
REAR OIL SEAL.................9-209,9-277
RETAINER - REMOVAL, DRIP RAIL
WEATHERSTRIP.....................23-92
RETAINER/BULKHEAD - ASSEMBLY, 4C . . 21-363
RETAINER/BULKHEAD - DISASSEMBLY,
4C ...............................21-362
RETRACTOR - DESCRIPTION,
AUTOMATIC LOCKING.................8O-14
RETRACTOR - INSTALLATION, FRONT
CENTER SEAT BELT..................8O-29
RETRACTOR - INSTALLATION, REAR
CENTER SEAT BELT..................8O-45
RETRACTOR - INSTALLATION, REAR
OUTBOARD SEAT BELT................8O-47
RETRACTOR - OPERATION, AUTOMATIC
LOCKING...........................8O-14
RETRACTOR - REMOVAL, FRONT
CENTER SEAT BELT..................8O-29
RETRACTOR - REMOVAL, REAR CENTER
SEAT BELT .........................8O-44
RETRACTOR - REMOVAL, REAR
OUTBOARD SEAT BELT................8O-46
RETURN - DESCRIPTION, SENSOR.......8E-10
RETURN HOSE - GEAR TO COOLER -
INSTALLATION..................19-44,19-45
RETURN HOSE - GEAR TO COOLER -
REMOVAL.....................19-44,19-45
RETURN HOSE - INSTALLATION, HEATER . 24-65
RETURN HOSE - REMOVAL, HEATER.....24-64
RETURN HOSE - RESERVOIR TO
COOLER - INSTALLATION.........19-44,19-45
RETURN HOSE - RESERVOIR TO
COOLER - REMOVAL.............19-44,19-45
REVOLUTIONS PER MILE,
SPECIFICATIONS - TIRE...............22-10
RFE TRANSMISSION, SPECIAL TOOLS . . . 21-359
RING - INSTALLATION, PINION
GEAR/RING GEAR/TONE.....3-108,3-137,3-164
RING - REMOVAL, PINION GEAR/RING
GEAR/TONE...............3-106,3-134,3-162
RING FITTING - STANDARD
PROCEDURE, PISTON . . . 9-142,9-213,9-284,9-53
RINGS - ASSEMBLY, WITH INJECTED
......3-13
RINGS - ASSEMBLY, WITH SNAP
.........3-12
RINGS - DISASSEMBLY, WITH INJECTED
. . . 3-11
RINGS - DISASSEMBLY, WITH SNAP
......3-10
RKE TRANSMITTER BATTERIES -
STANDARD PROCEDURE
...............8N-8
DRINDEX 27
Description Group-Page Description Group-Page Description Group-Page

TEMPERATURE SENSOR -
INSTALLATION, EVAPORATOR...........24-22
TEMPERATURE SENSOR -
INSTALLATION, INTAKE AIR............14-31
TEMPERATURE SENSOR - OPERATION,
BATTERY...........................8F-21
TEMPERATURE SENSOR - OPERATION,
ENGINE COOLANT.....................7-38
TEMPERATURE SENSOR - OPERATION,
EVAPORATOR.......................24-22
TEMPERATURE SENSOR - OPERATION,
INTAKE AIR .........................14-30
TEMPERATURE SENSOR - OPERATION,
TRANSMISSION...............21-267,21-408
TEMPERATURE SENSOR - REMOVAL,
BATTERY...........................8F-21
TEMPERATURE SENSOR - REMOVAL,
ENGINE COOLANT.....................7-39
TEMPERATURE SENSOR - REMOVAL,
EVAPORATOR.......................24-22
TEMPERATURE SENSOR - REMOVAL,
INTAKE AIR .........................14-30
TEMPERATURE SENSOR CIRCUIT -
DIAGNOSIS AND TESTING, AMBIENT....8M-10
TEMPERATURE SENSOR/MAP SENSOR -
DESCRIPTION, INTAKE AIR.............14-82
TEMPERATURE SENSOR/MAP SENSOR -
INSTALLATION, INTAKE AIR............14-82
TEMPERATURE SENSOR/MAP SENSOR -
OPERATION, INTAKE AIR...............14-82
TEMPERATURE SENSOR/MAP SENSOR -
REMOVAL, INTAKE AIR................14-82
TEMPERATURE SENSOR/PRESSURE
SENSOR - DESCRIPTION, INLET AIR.......14-79
TEMPERATURE SENSOR/PRESSURE
SENSOR - INSTALLATION, INLET AIR.....14-79
TEMPERATURE SENSOR/PRESSURE
SENSOR - OPERATION, INLET AIR.......14-79
TEMPERATURE SENSOR/PRESSURE
SENSOR - REMOVAL, INLET AIR........14-79
TEMPORARY - DESCRIPTION, SPARE
TIRE................................22-6
TEMPORARY TIRE - DESCRIPTION,
SPARE .............................22-15
TENSION REDUCER - DESCRIPTION,
SEAT BELT .........................8O-53
TENSION REDUCER - DIAGNOSIS AND
TESTING, SEAT BELT.................8O-54
TENSION REDUCER - OPERATION, SEAT
BELT ..............................8O-54
TENSIONER - 3.7L / 4.7L -
DESCRIPTION, BELT...................7-21
TENSIONER - 3.7L / 4.7L -
INSTALLATION, BELT...................7-22
TENSIONER - 3.7L / 4.7L - OPERATION,
BELT ...............................7-21
TENSIONER - 3.7L / 4.7L - REMOVAL,
BELT ...............................7-21
TENSIONER - 5.9L DIESEL -
DESCRIPTION, BELT...................7-23
TENSIONER - 5.9L DIESEL -
INSTALLATION, BELT...................7-24
TENSIONER - 5.9L DIESEL - OPERATION,
BELT ...............................7-23
TENSIONER - 5.9L DIESEL - REMOVAL,
BELT ...............................7-23
TENSIONER - DESCRIPTION, SEAT BELT . . 8O-52
TENSIONER - OPERATION, SEAT BELT....8O-53
TENSIONER-5.7L - DESCRIPTION, BELT
....7-22
TENSIONER-5.7L - INSTALLATION, BELT
. . . 7-23
TENSIONER-5.7L - OPERATION, BELT
......7-22
TENSIONER-5.7L - REMOVAL, BELT
.......7-22
TERMINAL - INSTALLATION
.........8W-01-14
TERMINAL - REMOVAL
.............8W-01-14
TERMINAL REPAIR - STANDARD
PROCEDURE, GRID LINE
...............8G-4
TEST - DIAGNOSIS AND TESTING,
HEATER PERFORMANCE
................24-6
TEST - DIAGNOSIS AND TESTING,
HYDRAULIC PRESSURE
........21-141,21-316
TEST - DIAGNOSIS AND TESTING, ROAD
. . . 8P-3
TEST - DIAGNOSIS AND TESTING,
VACUUM SUPPLY
.....................8P-2
TEST - STANDARD PROCEDURE,
BUILT-IN INDICATOR
..................8F-10
TEST - STANDARD PROCEDURE,
IGNITION-OFF DRAW
..................8F-11TEST - STANDARD PROCEDURE,
OPEN-CIRCUIT VOLTAGE...............8F-10
TEST - STANDARD PROCEDURE,
VERIFICATION........................8O-9
TEST MODE - DESCRIPTION, CIRCUIT
ACTUATION..........................25-1
TEST MODE - DESCRIPTION, STATE
DISPLAY............................25-1
TESTER - STANDARD PROCEDURE,
USING MICRO 420 BATTERY............8F-12
TESTS - DIAGNOSIS AND TESTING,
CYLINDER COMPRESSION/LEAKAGE.....9-239
THEFT SECURITY SYSTEM, DIAGNOSIS
AND TESTING - VEHICLE...............8Q-3
THEFT/SECURITY SYSTEM -
DESCRIPTION, VEHICLE................8Q-1
THEFT/SECURITY SYSTEM - OPERATION,
VEHICLE............................8Q-1
THERMOSTAT - 3.7L/4.7L -
DESCRIPTION, ENGINE COOLANT.........7-44
THERMOSTAT - 3.7L/4.7L -
INSTALLATION, ENGINE COOLANT........7-45
THERMOSTAT - 3.7L/4.7L - OPERATION,
ENGINE COOLANT.....................7-44
THERMOSTAT - 3.7L/4.7L - REMOVAL,
ENGINE COOLANT.....................7-45
THERMOSTAT - 5.9L DIESEL -
DESCRIPTION, ENGINE COOLANT.........7-46
THERMOSTAT - 5.9L DIESEL -
INSTALLATION, ENGINE COOLANT........7-47
THERMOSTAT - 5.9L DIESEL -
OPERATION, ENGINE COOLANT..........7-46
THERMOSTAT - 5.9L DIESEL -
REMOVAL, ENGINE COOLANT.............7-47
THERMOSTAT - 8.0L - DESCRIPTION,
ENGINE COOLANT.....................7-48
THERMOSTAT - 8.0L - INSTALLATION,
ENGINE COOLANT.....................7-49
THERMOSTAT - 8.0L - OPERATION,
ENGINE COOLANT.....................7-48
THERMOSTAT - 8.0L - REMOVAL,
ENGINE COOLANT.....................7-49
THERMOSTAT - DIAGNOSIS AND
TESTING................7-42,7-44,7-47,7-48
THERMOSTAT-5.7L - DESCRIPTION,
ENGINE COOLANT.....................7-41
THERMOSTAT-5.7L - INSTALLATION,
ENGINE COOLANT.....................7-43
THERMOSTAT-5.7L - OPERATION,
ENGINE COOLANT.....................7-41
THERMOSTAT-5.7L - REMOVAL, ENGINE
COOLANT............................7-42
THREAD REPAIR - STANDARD
PROCEDURE, ALUMINUM.......21-158,21-318
THREADED HOLE REPAIR -
DESCRIPTION......................Intro.-8
THREADS - STANDARD PROCEDURE,
REPAIR DAMAGED OR WORN . . 9-190,9-240,9-9,
9-94
THROTTLE BODY - DESCRIPTION........14-36
THROTTLE BODY - INSTALLATION.......14-37
THROTTLE BODY - OPERATION.........14-36
THROTTLE BODY - REMOVAL...........14-36
THROTTLE CONTROL CABLE -
INSTALLATION..................14-40,14-84
THROTTLE CONTROL CABLE - REMOVAL . 14-38,
14-83
THROTTLE POSITION SENSOR -
DESCRIPTION.......................14-41
THROTTLE POSITION SENSOR -
INSTALLATION.......................14-43
THROTTLE POSITION SENSOR -
OPERATION.........................14-41
THROTTLE POSITION SENSOR -
REMOVAL..........................14-41
THROTTLE VALVE CABLE -
ADJUSTMENTS.....................21-254
THROTTLE VALVE CABLE - DESCRIPTION . 21-253
TIE DOWN - INSTALLATION, CARGO BOX . 23-38
TIE DOWN - REMOVAL, CARGO BOX.....23-38
TIE ROD END - DIAGNOSIS AND
TESTING, OUTER.....................19-32
TIE ROD END - INSTALLATION
..........19-37
TIE ROD END - INSTALLATION, OUTER
. . . 19-33
TIE ROD END - REMOVAL
..............19-37
TIE ROD END - REMOVAL, OUTER
.......19-32
TILT LEVER KNOB RELEASE -
INSTALLATION
.......................19-16TILT LEVER KNOB RELEASE - REMOVAL . . 19-16
TIMING - DESCRIPTION, VALVE..........9-76
TIMING - DIAGNOSIS AND TESTING,
FUEL INJECTION PUMP...............14-53
TIMING - OPERATION, VALVE............9-76
TIMING - VERIFICATION - STANDARD
PROCEDURE, ENGINE.................9-167
TIMING BELT / CHAIN COVER(S) -
INSTALLATION...................9-171,9-81
TIMING BELT / CHAIN COVER(S) -
REMOVAL......................9-170,9-81
TIMING BELT/CHAIN AND SPROCKETS -
INSPECTION....................9-174,9-84
TIMING BELT/CHAIN AND SPROCKETS -
INSTALLATION...................9-176,9-85
TIMING BELT/CHAIN AND SPROCKETS -
REMOVAL......................9-172,9-83
TIMING CHAIN WEAR - STANDARD
PROCEDURE, MEASURING.............9-167
TIMING CHAIN WEAR, STANDARD
PROCEDURE - MEASURING.............9-77
TIMING CHAIN/TENSIONER -
DESCRIPTION.......................9-229
TIMING CHAIN/TENSIONER - OPERATION . 9-229
TIMING DRIVE SYSTEM - DESCRIPTION . . 9-166
TIMING DRIVE SYSTEM - OPERATION....9-166
TIMING, SPECIFICATIONS - IGNITION......8I-5
TIMING VERIFICATION - SERVICE
PROCEDURE.........................9-77
TIMING VERIFICATION - STANDARD
PROCEDURE........................9-299
TIMING/CHAIN AND SPROCKETS -
INSTALLATION.......................9-228
TIMING/CHAIN AND SPROCKETS -
REMOVAL..........................9-228
TIMING/CHAIN COVER - INSTALLATION . . . 9-227
TIMING/CHAIN COVER - REMOVAL.......9-227
TIP INSERTS - INSTALLATION, SPRING....2-45
TIP INSERTS - REMOVAL, SPRING........2-44
TIP REPLACEMENT - STANDARD
PROCEDURE, LIGHT DUTY FRONT
FRAME RAIL.........................13-4
TIRE - DESCRIPTION, FULL SIZE, SPARE
WHEEL WITH MATCHING..............22-15
TIRE - DESCRIPTION, SPARE /
TEMPORARY........................22-15
TIRE / TEMPORARY - DESCRIPTION,
SPARE..............................22-6
TIRE AND WHEEL BALANCE -
STANDARD PROCEDURE................22-4
TIRE AND WHEEL RUNOUT - DIAGNOSIS
AND TESTING........................22-1
TIRE INFLATION PRESSURES -
DESCRIPTION........................22-7
TIRE NOISE OR VIBRATION - DIAGNOSIS
AND TESTING........................22-7
TIRE PRESSURE FOR HIGH SPEEDS -
DESCRIPTION........................22-7
TIRE REVOLUTIONS PER MILE,
SPECIFICATIONS.....................22-10
TIRE ROTATION - STANDARD
PROCEDURE.........................22-3
TIRE WEAR PATTERNS - DIAGNOSIS
AND TESTING........................22-8
TIRES - DESCRIPTION.................22-6
TIRES - DESCRIPTION, RADIAL - PLY.....22-6
TIRES - DESCRIPTION, REPLACEMENT....22-7
TIRE/VEHICLE LEAD - DIAGNOSIS AND
TESTING............................22-8
TOE ADJUSTMENT - STANDARD
PROCEDURE..........................2-4
TOE ADJUSTMENT - STANDARD
PROCEDURE, CAMBER, CASTER
..........2-4
TOOL - ADJUSTMENT, WITH ADJUSTING
. . . 5-42
TOOLS - 4.7L ENGINE, SPECIAL
.........9-103
TOOLS - 5.7L ENGINE, SPECIAL
.........9-196
TOOLS - 5.9L DIESEL ENGINE, SPECIAL
. . 9-246
TOOLS - 9 1/4 AA, SPECIAL
.............2-30
TOOLS - BASE BRAKES, SPECIAL
.........5-5
TOOLS - BATTERY SYSTEM SPECIAL
TOOLS, SPECIAL
......................8F-7
TOOLS - BODY, SPECIAL
...............23-14
TOOLS - COOLING, SPECIAL
.............7-20
TOOLS - DIESEL FUEL SYSTEM,
SPECIAL
...........................14-49
TOOLS - FRONT SUSPENSION, SPECIAL
. . . 2-12
TOOLS - FUEL SYSTEM, SPECIAL
........14-5
DRINDEX 33
Description Group-Page Description Group-Page Description Group-Page