1998 DODGE RAM 1500 brake shoes

(12) Rotate rotor to verify that the park brake
shoes are not dragging on the brake drum. If park
brake shoes are dragging, remove rotor and back off
star wheel adjuster one notch and recheck for brake
shoe drag against drum. Continue with the previous
step until brake shoes are not dragging on brake
drum.
(13) Install disc brake caliper on caliper adapter
(Refer to 5 - BRAKES/HYDRAULIC/MECHANICAL/
DISC BRAKE CALIPERS - INSTALLATION).
(14) Install wheel and tire.
(15) Tighten the wheel mounting nuts in the
proper sequence until all nuts are torqued to half the
specified torque. Then repeat the tightening sequence
to the full specified torque of 180 N´m (135 ft. lbs.)
1500 & 2500 Series or 195 N´m (145 ft. lbs.) 3500
Series.
(16) Lower vehicle.
(17) Apply and release the park brake pedal one
time. This will seat and correctly adjust the park
brake cables.
CAUTION: Before moving vehicle, pump brake
pedal several times to ensure the vehicle has a firm
enough pedal to stop the vehicle.
NOTE: On a new vehicle or after parking brake lin-
ing replacement, it is recommended that the park-
ing brake system be conditioned prior to use. This
is done by making one stop from 25 mph on dry
pavement or concrete using light to moderate force
on the parking brake foot pedal.
(18) Road test the vehicle to ensure proper func-
tion of the vehicle's brake system.
ADJUSTMENT - WITH ADJUSTING TOOL
Adjustment can be made with a standard brake
gauge or with adjusting tool. Adjustment is per-
formed with the complete brake assembly installed
on the backing plate.
(1) Be sure parking brake lever is fully released.
(2) Raise vehicle so rear wheels can be rotated
freely.
(3) Remove plug from each access hole in brake
support plates.
(4) Loosen parking brake cable adjustment nut
until there is slack in front cable.
(5) Insert adjusting tool through support plate
access hole and engage tool in teeth of adjusting
screw star wheel (Fig. 82).
(6) Rotate adjuster screw star wheel (move tool
handle upward) until slight drag can be felt when
wheel is rotated.
(7) Back off adjuster screw star wheel until brake
drag is eliminated.(8) Repeat adjustment at opposite wheel. Be sure
adjustment is equal at both wheels.
(9) Install support plate access hole plugs.
(10) Adjust parking brake cable and lower vehicle.
(11) Depress park brake pedal and make sure park
brakes hold the vehicle staionary.
(12) Release park brake pedal.
PEDAL
REMOVAL
(1) Release the parking brake.
(2) Raise the vehicle.
(3) Loosen the cable tensioner nut at the equalizer
to create slack in the front cable.
(4) Lower the vehicle.
(5) Remove the knee bolster, (Refer to 23 - BODY/
INSTRUMENT PANEL/STEERING COLUMN
OPENING COVER - REMOVAL).
(6) Disconnect the brake lamp wire from the
switch on the pedal assembly.
(7) Roll the carpet back, loosen the front cable
grommet from the floorpan and the cable retainer.
(8) Disengage the release rod (Fig. 83) from the
arm on the pedal assembly.
(9) Remove the bolts/nuts from the pedal assembly
and remove the assembly.
INSTALLATION
(1) Position the replacement pedal assembly on the
dash and cowl.
Fig. 82 Brake Adjustment
1 - STAR WHEEL
2 - LEVER
3 - BRAKE SHOE WEB
4 - SCREWDRIVER
5 - ADJUSTING TOOL
6 - ADJUSTER SPRING
5 - 42 BRAKES - BASEDR
SHOES (Continued)

(2) Install the bolts/nuts and tighten to 28 N´m (21
ft. lbs.) (Fig. 84).
(3) Install the park brake release rod.
(4) Connect the front cable to the arm on the pedal
assembly.
(5) Install the front cable grommet into the floor-
pan and the cable retainer, roll the carpet back.
(6) Connect the wires to the brake lamp switch.
(7) Install the knee bolster, (Refer to 23 - BODY/
INSTRUMENT PANEL/STEERING COLUMN
OPENING COVER - INSTALLATION).
(8) Raise the vehicle.
(9) Adjust the parking brake cable tensioner (Refer
to 5 - BRAKES/PARKING BRAKE/CABLE TEN-
SIONER - ADJUSTMENTS).
CABLE TENSIONER
ADJUSTMENTS
ADJUSTMENT
NOTE: Tensioner adjustment is only necessary
when the tensioner, or a cable has been replaced or
disconnected for service. When adjustment is nec-
essary, perform adjustment only as described in the
following procedure. This is necessary to avoid
faulty park brake operation.
(1) Raise the vehicle.
(2) Back off the cable tensioner adjusting nut to
create slack in the cables.
(3) Remove the rear wheel/tire assemblies. Then
remove the brake rotors (Refer to 5 - BRAKES/HY-
DRAULIC/MECHANICAL/ROTORS - REMOVAL).
(4) Verify the brakes are in good condition and
operating properly.
(5) Verify the park brake cables operate freely and
are not binding, or seized.
(6) Check the rear brake shoe adjustment with
standard brake gauge (Refer to 5 - BRAKES/PARK-
ING BRAKE/SHOES - ADJUSTMENTS).
(7) Install the rotors (Refer to 5 - BRAKES/HY-
DRAULIC/MECHANICAL/ROTORS - INSTALLA-
TION) and verify that the rotors rotate freely
without drag.
(8) Install the wheel/tire assemblies, (Refer to 22 -
TIRES/WHEELS/WHEELS - STANDARD PROCE-
DURE).
(9) Lower the vehicle enough for access to the park
brake foot pedal. Then fully apply the park brakes.
NOTE: Leave park brakes applied until adjustment
is complete.
(10) Raise the vehicle again.
(11) Mark the tensioner rod 6.35 mm (1/4 in.) from
edge of the tensioner (Fig. 85).
(12) Tighten the adjusting nut on the tensioner rod
until the mark is no longer visible.
CAUTION: Do not loosen, or tighten the tensioner
adjusting nut for any reason after completing
adjustment.
(13) Lower the vehicle until the rear wheels are
15-20 cm (6-8 in.) off the shop floor.
(14) Release the park brake foot pedal and verify
that rear wheels rotate freely without drag. Then
lower the vehicle.
Fig. 83 PARKING BRAKE PEDAL
1 - RELEASE ROD
2 - PEDAL ASSEMBLY
Fig. 84 PARKING BRAKE ASSEMBLY
1 - PEDAL ASSEMBLY
2 - MOUNTING NUT
DRBRAKES - BASE 5 - 43
PEDAL (Continued)

BLOCK - DIAGNOSIS AND TESTING,
BLOWER MOTOR RESISTOR............24-19
BLOCK - INSPECTION, ENGINE . 9-128,9-205,9-39
BLOCK - INSTALLATION, BLOWER
MOTOR RESISTOR...................24-19
BLOCK - INSTALLATION, BRAKE
JUNCTION...........................5-24
BLOCK - OPERATION, BLOWER MOTOR
RESISTOR..........................24-18
BLOCK - REMOVAL, BLOWER MOTOR
RESISTOR..........................24-19
BLOCK - REMOVAL, BRAKE JUNCTION....5-24
BLOCK HEATER - 5.9L DIESEL -
DESCRIPTION, ENGINE.................7-37
BLOCK HEATER - 5.9L DIESEL -
INSTALLATION, ENGINE................7-38
BLOCK HEATER - 5.9L DIESEL -
OPERATION, ENGINE...................7-38
BLOCK HEATER - 5.9L DIESEL -
REMOVAL, ENGINE....................7-38
BLOCK HEATER - DESCRIPTION, ENGINE . . . 7-36
BLOCK HEATER - DIAGNOSIS AND
TESTING, ENGINE.....................7-36
BLOCK HEATER - INSTALLATION,
ENGINE.............................7-37
BLOCK HEATER - OPERATION, ENGINE....7-36
BLOCK HEATER - REMOVAL, ENGINE......7-37
BLOCK REFACING - STANDARD
PROCEDURE, CYLINDER...............9-264
BLOWER MOTOR - DESCRIPTION.......24-28
BLOWER MOTOR - DIAGNOSIS AND
TESTING.............................24-28
BLOWER MOTOR - INSTALLATION.......24-31
BLOWER MOTOR - OPERATION.........24-28
BLOWER MOTOR - REMOVAL...........24-31
BLOWER MOTOR RESISTOR BLOCK -
DESCRIPTION.......................24-18
BLOWER MOTOR RESISTOR BLOCK -
DIAGNOSIS AND TESTING.............24-19
BLOWER MOTOR RESISTOR BLOCK -
INSTALLATION.......................24-19
BLOWER MOTOR RESISTOR BLOCK -
OPERATION.........................24-18
BLOWER MOTOR RESISTOR BLOCK -
REMOVAL..........................24-19
BLOWER MOTOR SWITCH -
DESCRIPTION.......................24-20
BLOWER MOTOR SWITCH - DIAGNOSIS
AND TESTING.......................24-20
BLOWER MOTOR SWITCH - OPERATION . . 24-20
BODY - ADJUSTMENTS, VALVE........21-310
BODY - ASSEMBLY, VALVE......21-299,21-414
BODY & CABLE - DESCRIPTION,
ANTENNA...........................8A-4
BODY & CABLE - INSTALLATION,
ANTENNA...........................8A-6
BODY & CABLE - OPERATION, ANTENNA . . . 8A-4
BODY & CABLE - REMOVAL, ANTENNA....8A-6
BODY - CLEANING, VALVE......21-298,21-412
BODY - DESCRIPTION, THROTTLE.......14-36
BODY - DESCRIPTION, VALVE....21-267,21-408
BODY - DISASSEMBLY, VALVE . . . 21-287,21-410
BODY - INSPECTION, VALVE.....21-298,21-413
BODY - INSTALLATION, THROTTLE.......14-37
BODY - INSTALLATION, VALVE . . . 21-309,21-414
BODY - OPERATION, THROTTLE.........14-36
BODY - OPERATION, VALVE.....21-272,21-408
BODY - REMOVAL, THROTTLE..........14-36
BODY - REMOVAL, VALVE.......21-286,21-410
BODY AND CABLE - DIAGNOSIS AND
TESTING, ANTENNA
...................8A-4
BODY CODE PLATE - DESCRIPTION
.....Intro.-3
BODY ISOLATORS - INSTALLATION
......23-37
BODY ISOLATORS - REMOVAL
..........23-36
BODY LUBRICATION - STANDARD
PROCEDURE
.........................23-3
BODY OPENING DIMENSIONS -
SPECIFICATIONS
.....................23-99
BODY PANEL REPAIR - STANDARD
PROCEDURE, PLASTIC
.................23-3
BODY SIDE MOLDINGS - INSTALLATION
. . 23-36
BODY SIDE MOLDINGS - REMOVAL
......23-36
BODY, SPECIAL TOOLS
................23-14
BODY VENT - INSTALLATION
...........23-71
BODY VENT - REMOVAL
...............23-71
BOOST PRESSURE - DIAGNOSIS AND
TESTING, TURBOCHARGER
.............11-11BOOSTER - DESCRIPTION, POWER
BRAKE..............................5-29
BOOSTER - DIAGNOSIS AND TESTING,
HYDRAULIC..........................5-30
BOOSTER - DIAGNOSIS AND TESTING,
MASTER CYLINDER/POWER.............5-25
BOOSTER - INSTALLATION, HYDRO-
BOOST BRAKE........................5-32
BOOSTER - INSTALLATION, POWER
BRAKE..............................5-29
BOOSTER - OPERATION, POWER BRAKE . . . 5-29
BOOSTER - REMOVAL, HYDRO-BOOST
BRAKE..............................5-31
BOOSTER - REMOVAL, POWER BRAKE....5-29
BOOT - INSTALLATION, 4WD FLOOR
SHIFT..............................23-62
BOOT - INSTALLATION, EXTENSION
HOUSING SEAL AND DUST......21-476,21-571
BOOT - REMOVAL, 4WD FLOOR SHIFT....23-62
BOOT - REMOVAL, EXTENSION HOUSING
SEAL AND DUST..............21-476,21-571
BORE - DE-GLAZE - STANDARD
PROCEDURE, CYLINDER...............9-264
BORE HONING - STANDARD
PROCEDURE, CYLINDER...........9-128,9-38
BORE REPAIR - STANDARD
PROCEDURE, CAM...................9-267
BORE REPAIR - STANDARD
PROCEDURE, CYLINDER...............9-265
BOX - INSTALLATION, CARGO..........23-37
BOX - INSTALLATION, GLOVE...........23-52
BOX - INSTALLATION, WITH CARGO . 8L-22,8L-23,
8L-24,8L-7,8L-9
BOX - INSTALLATION, WITHOUT CARGO . . 8L-22,
8L-23,8L-24,8L-8,8L-9
BOX - REMOVAL, CARGO..............23-37
BOX - REMOVAL, GLOVE..............23-52
BOX - REMOVAL, WITH CARGO....8L-22,8L-24,
8L-7,8L-9
BOX - REMOVAL, WITHOUT CARGO.....8L-22,
8L-23,8L-24,8L-7,8L-9
BOX - TIE DOWN - INSTALLATION,
CARGO............................23-38
BOX - TIE DOWN - REMOVAL, CARGO....23-38
BOX LAMP/SWITCH - INSTALLATION,
GLOVE.............................8L-28
BOX LAMP/SWITCH - REMOVAL, GLOVE . . 8L-27
BOX LATCH - INSTALLATION, GLOVE.....23-52
BOX LATCH - REMOVAL, GLOVE.........23-52
B-PILLAR GRAB HANDLE -
INSTALLATION.......................23-68
B-PILLAR GRAB HANDLE - REMOVAL....23-68
B-PILLAR LOWER TRIM - INSTALLATION . . 23-64
B-PILLAR LOWER TRIM - REMOVAL.....23-63
B-PILLAR UPPER TRIM - INSTALLATION . . 23-64
B-PILLAR UPPER TRIM - REMOVAL......23-64
BRACKET - INSTALLATION, REAR VIEW
MIRROR SUPPORT...................23-70
BRACKET - INSTALLATION, STEERING
COLUMN OPENING SUPPORT...........23-60
BRACKET - REMOVAL, STEERING
COLUMN OPENING SUPPORT...........23-60
BRACKETS - INSTALLATION, SEAT BACK
REAR - FOOTMANS LOOP..............23-85
BRACKETS - REMOVAL, SEAT BACK
REAR - FOOTMANS LOOP..............23-85
BRAKE - CLEANING, REAR DRUM IN
HAT ................................5-39
BRAKE - DESCRIPTION, CONTROLLER
ANTILOCK...........................8E-3
BRAKE - DESCRIPTION, PARKING........5-36
BRAKE - INSPECTION, REAR DRUM IN
HAT ................................5-39
BRAKE - INSTALLATION, CONTROLLER
ANTILOCK...........................8E-3
BRAKE - OPERATION, CONTROLLER
ANTILOCK...........................8E-3
BRAKE - OPERATION, PARKING..........5-36
BRAKE - REMOVAL, CONTROLLER
ANTILOCK
...........................8E-3
BRAKE BLEEDING - STANDARD
PROCEDURE, ABS
.....................5-46
BRAKE BOOSTER - DESCRIPTION,
POWER
.............................5-29
BRAKE BOOSTER - INSTALLATION,
HYDRO-BOOST
.......................5-32
BRAKE BOOSTER - INSTALLATION,
POWER
.............................5-29BRAKE BOOSTER - OPERATION, POWER . . . 5-29
BRAKE BOOSTER - REMOVAL,
HYDRO-BOOST.......................5-31
BRAKE BOOSTER - REMOVAL, POWER....5-29
BRAKE CABLE - INSTALLATION, FRONT
PARKING............................5-38
BRAKE CABLE - INSTALLATION, REAR
PARK...............................5-38
BRAKE CABLE - REMOVAL, FRONT
PARKING............................5-36
BRAKE CABLE - REMOVAL, REAR PARK . . . 5-37
BRAKE CALIPER ADAPTER MOUNT -
INSTALLATION, DISC...................5-22
BRAKE CALIPERS - DESCRIPTION, DISC . . . 5-16
BRAKE CALIPERS - OPERATION, DISC.....5-16
BRAKE FLUID CONTAMINATION -
DIAGNOSIS AND TESTING..............5-23
BRAKE FLUID LEVEL - STANDARD
PROCEDURE.........................5-23
BRAKE FLUID, SPECIFICATIONS..........5-23
BRAKE HOSE - INSTALLATION, FRONT.....5-13
BRAKE HOSE - INSTALLATION, REAR......5-12
BRAKE HOSE - REMOVAL, REAR.........5-11
BRAKE INDICATOR - DESCRIPTION,
BRAKE/PARK........................8J-19
BRAKE INDICATOR - DIAGNOSIS AND
TESTING...........................8J-20
BRAKE INDICATOR - OPERATION,
BRAKE/PARK........................8J-19
BRAKE JUNCTION BLOCK -
INSTALLATION.........................5-24
BRAKE JUNCTION BLOCK - REMOVAL.....5-24
BRAKE LAMP SWITCH - DESCRIPTION....8L-9
BRAKE LAMP SWITCH - DIAGNOSIS
AND TESTING.......................8L-10
BRAKE LAMP SWITCH - INSTALLATION . . . 8L-11
BRAKE LAMP SWITCH - OPERATION......8L-9
BRAKE LAMP SWITCH - REMOVAL......8L-10
BRAKE PROPORTIONING -
DESCRIPTION, ELECTRONIC VARIABLE....5-49
BRAKE PROPORTIONING - OPERATION,
ELECTRONIC VARIABLE................5-49
BRAKE ROTOR, DIAGNOSIS AND
TESTING - DISC......................5-32
BRAKE SHOES - ADJUSTMENT, PARKING . . 5-41
BRAKE, SPECIFICATIONS - BASE.........5-10
BRAKE SYSTEM - DIAGNOSIS AND
TESTING, BASE........................5-2
BRAKE TRANSMISSION SHIFT
INTERLOCK - ADJUSTMENTS....21-196,21-365
BRAKE TRANSMISSION SHIFT
INTERLOCK - DIAGNOSIS AND
TESTING....................21-196,21-364
BRAKE TRANSMISSION SHIFT
INTERLOCK SYSTEM - DESCRIPTION . . . 21-196,
21-364
BRAKE TRANSMISSION SHIFT
INTERLOCK SYSTEM - OPERATION.....21-196,
21-364
BRAKE/PARK BRAKE INDICATOR -
DESCRIPTION.......................8J-19
BRAKE/PARK BRAKE INDICATOR -
OPERATION.........................8J-19
BRAKES - ABS - DESCRIPTION...........5-45
BRAKES - ABS - OPERATION............5-45
BRAKES, SPECIAL TOOLS - BASE.........5-5
BREAK-IN - STANDARD PROCEDURE,
A/C COMPRESSOR CLUTCH............24-10
BREATHER - INSTALLATION,
CRANKCASE
........................9-243
BREATHER - REMOVAL, CRANKCASE
.....9-242
BUCKLE - INSTALLATION, FRONT
OUTBOARD SEAT BELT
................8O-38
BUCKLE - REMOVAL, FRONT OUTBOARD
SEAT BELT
.........................8O-37
BUILT-IN INDICATOR TEST - STANDARD
PROCEDURE
........................8F-10
BUMPER - INSTALLATION, FRONT
........13-2
BUMPER - INSTALLATION, JOUNCE
.......2-43
BUMPER - INSTALLATION, REAR
.........13-4
BUMPER - REMOVAL, FRONT
............13-2
BUMPER - REMOVAL, JOUNCE
...........2-43
BUMPER - REMOVAL, REAR
.............13-3
BUMPERS (3500) - INSTALLATION,
AUXILIARY SPRING
....................2-43
BUMPERS (3500) - REMOVAL,
AUXILIARY SPRING
....................2-43
4 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

OUTER TIE ROD END - REMOVAL.......19-32
OUTLET - DESCRIPTION, CIGAR
LIGHTER.........................8W-97-2
OUTLET - DESCRIPTION, POWER......8W-97-7
OUTLET - DIAGNOSIS AND TESTING,
CIGAR LIGHTER...................8W-97-2
OUTLET - DIAGNOSIS AND TESTING,
POWER..........................8W-97-7
OUTLET - INSTALLATION, POWER.....8W-97-8
OUTLET - OPERATION, CIGAR LIGHTER . 8W-97-2
OUTLET - OPERATION, POWER.......8W-97-7
OUTLET - REMOVAL, POWER.........8W-97-8
OUTLETS - DESCRIPTION, AIR..........24-26
OUTLETS - INSTALLATION, AIR.........24-27
OUTLETS - REMOVAL, AIR.............24-26
OUTPUT - DESCRIPTION, PCM...........8I-5
OUTPUT - OPERATION, PCM............14-27
OUTPUT - OPERATION, PCM.............8I-5
OUTPUT SHAFT FRONT BEARING -
INSTALLATION......................21-216
OUTPUT SHAFT FRONT BEARING -
REMOVAL.........................21-216
OUTPUT SHAFT REAR BEARING -
INSTALLATION......................21-217
OUTPUT SHAFT REAR BEARING -
REMOVAL.........................21-216
OUTPUT SHAFT SEAL - INSTALLATION,
FRONT....21-442,21-477,21-508,21-538,21-572
OUTPUT SHAFT SEAL - REMOVAL,
FRONT.....21-441,21-477,21-507,21-537,21-572
OUTPUT SPEED SENSOR - DESCRIPTION . 21-391
OUTPUT SPEED SENSOR -
INSTALLATION......................21-392
OUTPUT SPEED SENSOR - OPERATION . . 21-391
OUTPUT SPEED SENSOR - REMOVAL . . . 21-391
OVERDRIVE CLUTCH - DESCRIPTION....21-217
OVERDRIVE CLUTCH - OPERATION.....21-217
OVERDRIVE ELECTRICAL CONTROLS -
DIAGNOSIS AND TESTING............21-262
OVERDRIVE SWITCH - DESCRIPTION,
TOW/HAUL..................21-261,21-392
OVERDRIVE SWITCH - INSTALLATION,
TOW/HAUL..................21-262,21-393
OVERDRIVE SWITCH - OPERATION,
TOW/HAUL..................21-262,21-392
OVERDRIVE SWITCH - REMOVAL,
TOW/HAUL..................21-262,21-392
OVERDRIVE UNIT - ASSEMBLY.........21-226
OVERDRIVE UNIT - CLEANING.........21-225
OVERDRIVE UNIT - DISASSEMBLY......21-218
OVERDRIVE UNIT - INSPECTION.......21-225
OVERDRIVE UNIT - INSTALLATION......21-235
OVERDRIVE UNIT - REMOVAL.........21-218
OVERFLOW VALVE - DESCRIPTION,
CASCADE...........................14-66
OVERFLOW VALVE - OPERATION,
CASCADE...........................14-66
OVERHEAD CONSOLE - DESCRIPTION....8M-1
OVERHEAD CONSOLE - DIAGNOSIS AND
TESTING............................8M-2
OVERHEAD CONSOLE - OPERATION......8M-2
OVERHEAD CONSOLE REMOVAL,
REMOVAL
...........................8M-6
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
ASSEMBLY
.........................21-237
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
CLEANING
.........................21-236
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
DESCRIPTION
......................21-236
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
DISASSEMBLY
......................21-236
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
INSPECTION
.......................21-237
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
OPERATION
........................21-236
OXYGEN SENSOR - DESCRIPTION
.......14-35
OXYGEN SENSOR - INSTALLATION
.......14-36
OXYGEN SENSOR - REMOVAL
..........14-35
PAINT CODE - DESCRIPTION
...........23-73
PAINT CODES - SPECIFICATIONS
........23-73
PAINT TOUCH-UP - DESCRIPTION
.......23-74PAINT TOUCH-UP - STANDARD
PROCEDURE........................23-74
PAN - CLEANING, OIL.............9-293,9-66
PAN - DESCRIPTION, OIL...............9-66
PAN - INSPECTION, OIL...........9-293,9-66
PAN - INSTALLATION, OIL . . . 9-155,9-224,9-293,
9-66
PAN - REMOVAL, OIL . . . 9-155,9-224,9-293,9-66
PANEL - INSTALLATION, TRIM.....23-24,23-33
PANEL - REMOVAL, TRIM.........23-24,23-33
PANEL ANTENNA CABLE -
INSTALLATION, INSTRUMENT............8A-7
PANEL ANTENNA CABLE - REMOVAL,
INSTRUMENT........................8A-7
PANEL ASSEMBLY - INSTALLATION,
INSTRUMENT.......................23-55
PANEL ASSEMBLY - REMOVAL,
INSTRUMENT.......................23-52
PANEL CENTER BEZEL - INSTALLATION,
INSTRUMENT.......................23-57
PANEL CENTER BEZEL - REMOVAL,
INSTRUMENT.......................23-57
PANEL DEMISTER DUCTS -
INSTALLATION, INSTRUMENT...........24-37
PANEL DEMISTER DUCTS - REMOVAL,
INSTRUMENT.......................24-36
PANEL DRIVER SIDE BEZEL -
INSTALLATION, INSTRUMENT...........23-58
PANEL DRIVER SIDE BEZEL - REMOVAL,
INSTRUMENT.......................23-58
PANEL DUCTS - INSTALLATION,
INSTRUMENT.........................24-37
PANEL DUCTS - REMOVAL,
INSTRUMENT.......................24-37
PANEL HEADLAMP SWITCH BEZEL -
INSTALLATION, INSTRUMENT...........23-56
PANEL HEADLAMP SWITCH BEZEL -
REMOVAL, INSTRUMENT..............23-56
PANEL LOWER SURROUND -
INSTALLATION, INSTRUMENT...........23-59
PANEL LOWER SURROUND - REMOVAL,
INSTRUMENT.......................23-59
PANEL REPAIR - STANDARD
PROCEDURE, PLASTIC BODY............23-3
PANEL TOP COVER - INSTALLATION,
INSTRUMENT.......................23-59
PANEL TOP COVER - REMOVAL,
INSTRUMENT.......................23-58
PANEL TRIM - INSTALLATION, REAR
CAB BACK..........................23-69
PANEL TRIM - REMOVAL, REAR CAB
BACK..............................23-68
PARK BRAKE CABLE - INSTALLATION,
REAR...............................5-38
PARK BRAKE CABLE - REMOVAL, REAR . . . 5-37
PARK LAMP RELAY - DESCRIPTION......8L-20
PARK LAMP RELAY - DIAGNOSIS AND
TESTING...........................8L-20
PARK LAMP RELAY - INSTALLATION.....8L-21
PARK LAMP RELAY - OPERATION.......8L-20
PARK LAMP RELAY - REMOVAL.........8L-21
PARKING BRAKE - DESCRIPTION.........5-36
PARKING BRAKE - OPERATION...........5-36
PARKING BRAKE CABLE -
INSTALLATION, FRONT.................5-38
PARKING BRAKE CABLE - REMOVAL,
FRONT..............................5-36
PARKING BRAKE SHOES - ADJUSTMENT
. . . 5-41
PARK/TURN SIGNAL LAMP -
INSTALLATION
.......................8L-21
PARK/TURN SIGNAL LAMP - REMOVAL
. . . 8L-21
PARTS - STANDARD PROCEDURES,
CLEANING FUEL SYSTEM
..............14-47
PASSENGER AIRBAG - DESCRIPTION
....8O-39
PASSENGER AIRBAG - INSTALLATION
....8O-41
PASSENGER AIRBAG - OPERATION
......8O-40
PASSENGER AIRBAG - REMOVAL
........8O-40
PASSENGER AIRBAG ON/OFF SWITCH -
DESCRIPTION
.......................8O-42
PASSENGER AIRBAG ON/OFF SWITCH -
INSTALLATION
......................8O-44
PASSENGER AIRBAG ON/OFF SWITCH -
OPERATION
.........................8O-43
PASSENGER AIRBAG ON/OFF SWITCH -
REMOVAL
..........................8O-43
PASSENGER SEAT SWITCH -
DESCRIPTION
.......................8N-15PASSENGER SEAT SWITCH - DIAGNOSIS
AND TESTING.......................8N-16
PASSENGER SEAT SWITCH -
INSTALLATION......................8N-16
PASSENGER SEAT SWITCH - OPERATION . 8N-15
PASSENGER SEAT SWITCH - REMOVAL . . . 8N-16
PATTERNS - DIAGNOSIS AND TESTING,
TIRE WEAR..........................22-8
PCM - DESCRIPTION...................8E-7
PCM - OPERATION...................8E-10
PCM INPUT - OPERATION, ASD SENSE.....8I-5
PCM OUTPUT - DESCRIPTION............8I-5
PCM OUTPUT - OPERATION............14-27
PCM OUTPUT - OPERATION.............8I-5
PCM/SKIM PROGRAMMING - STANDARD
PROCEDURE........................8E-14
PCV VALVE - 3.7L V-6/ 4.7L V-8 -
DIAGNOSIS AND TESTING.............25-20
PCV VALVE - DESCRIPTION............25-17
PCV VALVE - INSTALLATION............25-21
PCV VALVE - OPERATION..............25-19
PCV VALVE - REMOVAL...............25-21
PEDAL - DESCRIPTION.................5-28
PEDAL - INSTALLATION............5-28,5-42
PEDAL - INSTALLATION, ACCELERATOR . . . 14-21
PEDAL - OPERATION...................5-28
PEDAL - REMOVAL................5-28,5-42
PEDAL - REMOVAL, ACCELERATOR........14-21
PEDAL MOTOR - DESCRIPTION,
ADJUSTABLE..........................5-6
PEDAL MOTOR - INSTALLATION,
ADJUSTABLE..........................5-7
PEDAL MOTOR - REMOVAL,
ADJUSTABLE..........................5-7
PEDAL POSITION SENSOR -
DESCRIPTION, ACCELERATOR.....14-22,14-68
PEDAL POSITION SENSOR -
INSTALLATION, ACCELERATOR.....14-22,14-71
PEDAL POSITION SENSOR - OPERATION,
ACCELERATOR.................14-22,14-68
PEDAL POSITION SENSOR - REMOVAL,
ACCELERATOR.................14-22,14-68
PEDAL POSITION SWITCH -
DESCRIPTION, CLUTCH.................6-13
PEDAL POSITION SWITCH - DIAGNOSIS
AND TESTING, CLUTCH.................6-13
PEDAL POSITION SWITCH - OPERATION,
CLUTCH.............................6-13
PEDAL SWITCH - INSTALLATION,
ADJUSTABLE..........................5-6
PEDAL SWITCH - REMOVAL,
ADJUSTABLE..........................5-6
PER MILE, SPECIFICATIONS - TIRE
REVOLUTIONS.......................22-10
PERFORMANCE - DIAGNOSIS AND
TESTING, A/C........................24-3
PERFORMANCE - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS . . . 9-183,9-4,9-90
PERFORMANCE TEST - DIAGNOSIS AND
TESTING, HEATER.....................24-6
PILOT BEARING - INSTALLATION.........6-12
PILOT BEARING - REMOVAL.............6-11
PINION GEAR/RING GEAR -
INSTALLATION....................3-51,3-77
PINION GEAR/RING GEAR - REMOVAL . 3-49,3-75
PINION GEAR/RING GEAR/TONE RING -
INSTALLATION.............3-108,3-137,3-164
PINION GEAR/RING GEAR/TONE RING -
REMOVAL................3-106,3-134,3-162
PINION SEAL - INSTALLATION . 3-126,3-154,3-45,
3-71,3-96
PINION SEAL - REMOVAL....3-126,3-153,3-44,
3-70,3-95
PIPE - INSPECTION, EXHAUST.......11-7,11-8
PISTON & CONNECTING ROD -
CLEANING.....................9-140,9-212
PISTON & CONNECTING ROD -
DESCRIPTION.........9-139,9-211,9-281,9-48
PISTON & CONNECTING ROD -
INSPECTION
...................9-140,9-213
PISTON & CONNECTING ROD -
INSTALLATION
..................9-140,9-213
PISTON & CONNECTING ROD -
REMOVAL
................9-139,9-212,9-281
PISTON AND CONNECTING ROD -
CLEANING
..........................9-282
PISTON FITTING - STANDARD
PROCEDURE
...............9-139,9-211,9-51
DRINDEX 23
Description Group-Page Description Group-Page Description Group-Page

SENSOR - REMOVAL, LINE PRESSURE
(LP)..............................21-383
SENSOR - REMOVAL, MAP.............14-33
SENSOR - REMOVAL, OUTPUT SPEED . . . 21-391
SENSOR - REMOVAL, OXYGEN..........14-35
SENSOR - REMOVAL, POSITION . . 21-443,21-478
SENSOR - REMOVAL, REAR WHEEL
SPEED..............................5-48
SENSOR - REMOVAL, THROTTLE
POSITION..........................14-41
SENSOR - REMOVAL, TRANSMISSION
RANGE............................21-265
SENSOR - REMOVAL, WATER IN FUEL....14-66
SENSOR CIRCUIT - DIAGNOSIS AND
TESTING, AMBIENT TEMPERATURE......8M-10
SENSOR RETURN - DESCRIPTION.......8E-10
SENSOR (TRS) - DIAGNOSIS AND
TESTING, TRANSMISSION RANGE......21-264
SENSOR/MAP SENSOR - DESCRIPTION,
INTAKE AIR TEMPERATURE............14-82
SENSOR/MAP SENSOR - INSTALLATION,
INTAKE AIR TEMPERATURE............14-82
SENSOR/MAP SENSOR - OPERATION,
INTAKE AIR TEMPERATURE............14-82
SENSOR/MAP SENSOR - REMOVAL,
INTAKE AIR TEMPERATURE............14-82
SENSOR/PRESSURE SENSOR -
DESCRIPTION, INLET AIR
TEMPERATURE......................14-79
SENSOR/PRESSURE SENSOR -
INSTALLATION, INLET AIR
TEMPERATURE......................14-79
SENSOR/PRESSURE SENSOR -
OPERATION, INLET AIR TEMPERATURE . . . 14-79
SENSOR/PRESSURE SENSOR -
REMOVAL, INLET AIR TEMPERATURE....14-79
SENSOR/SWITCH - DESCRIPTION, OIL
PRESSURE..........................9-67
SENSOR/SWITCH - INSTALLATION, OIL
PRESSURE..........................9-67
SENSOR/SWITCH - OPERATION, OIL
PRESSURE..........................9-67
SENSOR/SWITCH - REMOVAL, OIL
PRESSURE..........................9-67
SENTRY KEY IMMOBILIZER MODULE -
DESCRIPTION.......................8E-13
SENTRY KEY IMMOBILIZER MODULE -
INSTALLATION.......................8E-15
SENTRY KEY IMMOBILIZER MODULE -
OPERATION.........................8E-13
SENTRY KEY IMMOBILIZER MODULE -
REMOVAL..........................8E-15
SENTRY KEY IMMOBILIZER MODULE
(SKIM) - DESCRIPTION................8Q-1
SENTRY KEY IMMOBILIZER MODULE
(SKIM) - OPERATION..................8Q-2
SENTRY KEY IMMOBILIZER SYSTEM
INDICATOR LAMP - DESCRIPTION........8Q-5
SENTRY KEY IMMOBILIZER SYSTEM
INDICATOR LAMP - OPERATION..........8Q-5
SENTRY KEY IMMOBILIZER SYSTEM
INITIALIZATION, STANDARD
PROCEDURE.........................8Q-3
SENTRY KEY IMMOBILIZER SYSTEM
(SKIS) - DESCRIPTION.................8Q-1
SENTRY KEY IMMOBILIZER SYSTEM
(SKIS) - OPERATION...................8Q-2
SENTRY KEY IMMOBILIZER SYSTEM
TRANSPONDER PROGRAMMING,
STANDARD PROCEDURE...............8Q-4
SEPARATOR - DESCRIPTION, FUEL
FILTER / WATER .....................14-50
SEPARATOR - INSTALLATION, FUEL
FILTER / WATER .....................14-50
SEPARATOR - OPERATION, FUEL FILTER
/ WATER ...........................14-50
SEPARATOR - REMOVAL, FUEL FILTER /
WATER.............................14-50
SERVO - ASSEMBLY, FRONT...........21-209
SERVO - ASSEMBLY, REAR............21-251
SERVO - CLEANING, FRONT...........21-209
SERVO - CLEANING, REAR............21-251
SERVO - DESCRIPTION.................8P-6
SERVO - DESCRIPTION, FRONT
........21-208
SERVO - DESCRIPTION, REAR
.........21-251
SERVO - DISASSEMBLY, FRONT
........21-209
SERVO - DISASSEMBLY, REAR
.........21-251
SERVO - INSPECTION, FRONT
.........21-209SERVO - INSTALLATION................8P-6
SERVO - OPERATION..................8P-6
SERVO - OPERATION, FRONT..........21-208
SERVO - OPERATION, REAR...........21-251
SERVO - REMOVAL....................8P-6
SETTING TRANSMITTER CODES -
STANDARD PROCEDURE..............8M-12
SHAFT - ASSEMBLY, PLANETARY
GEARTRAIN/OUTPUT.................21-244
SHAFT - CAUTION, HALF................3-20
SHAFT - DESCRIPTION, PLANETARY
GEARTRAIN/OUTPUT.................21-241
SHAFT - DIAGNOSIS AND TESTING,
HALF...............................3-20
SHAFT - DIAGNOSIS AND TESTING,
PROPELLER...........................3-1
SHAFT - DISASSEMBLY, PLANETARY
GEARTRAIN/OUTPUT.................21-242
SHAFT - HD FRONT - INSTALLATION,
PROPELLER...........................3-7
SHAFT - HD FRONT - REMOVAL,
PROPELLER...........................3-7
SHAFT - INSPECTION, PLANETARY
GEARTRAIN/OUTPUT.................21-243
SHAFT - INSTALLATION, BALANCE........9-80
SHAFT - INSTALLATION, HALF...........3-21
SHAFT - INSTALLATION, IDLER.....9-179,9-81
SHAFT - INSTALLATION, REAR
PROPELLER...........................3-8
SHAFT - OPERATION, PLANETARY
GEARTRAIN/OUTPUT..................21-241
SHAFT - REMOVAL, BALANCE...........9-80
SHAFT - REMOVAL, HALF...............3-20
SHAFT - REMOVAL, IDLER.........9-179,9-81
SHAFT - REMOVAL, REAR PROPELLER.....3-8
SHAFT - SPECIAL TOOLS, HALF..........3-21
SHAFT - SPECIAL TOOLS, PROPELLER.....3-6
SHAFT - SPECIFICATIONS, HALF..........3-21
SHAFT - SPECIFICATIONS, PROPELLER.....3-6
SHAFT - STANDARD PROCEDURE,
PROPELLER...........................3-3
SHAFT FRONT BEARING -
INSTALLATION, OUTPUT..............21-216
SHAFT FRONT BEARING - REMOVAL,
OUTPUT...........................21-216
SHAFT- LD FRONT - INSTALLATION,
PROPELLER...........................3-7
SHAFT- LD FRONT - REMOVAL,
PROPELLER...........................3-6
SHAFT REAR BEARING - INSTALLATION,
OUTPUT...........................21-217
SHAFT REAR BEARING - REMOVAL,
OUTPUT...........................21-216
SHAFT SEAL - INSTALLATION, FRONT
OUTPUT . . . 21-442,21-477,21-508,21-538,21-572
SHAFT SEAL - INSTALLATION, STEERING
GEAR INPUT........................19-29
SHAFT SEAL - REMOVAL, FRONT
OUTPUT . . . 21-441,21-477,21-507,21-537,21-572
SHAFT SEAL - REMOVAL, STEERING
GEAR INPUT........................19-27
SHAFT SEALS - INSTALLATION, AXLE . 3-43,3-70,
3-94
SHAFT SEALS - REMOVAL, AXLE . 3-43,3-69,3-94
SHAFTS - ASSEMBLY, AXLE.............3-69
SHAFTS - DISASSEMBLY, AXLE..........3-68
SHAFTS - INSTALLATION, AXLE....3-124,3-152,
3-43,3-69,3-94
SHAFTS - REMOVAL, AXLE . . . 3-124,3-152,3-43,
3-67,3-93
SHIELD - INSTALLATION, FRONT
WHEELHOUSE SPLASH................23-41
SHIELD - INSTALLATION, REAR
WHEELHOUSE SPLASH................23-41
SHIELD - REMOVAL, FRONT
WHEELHOUSE SPLASH................23-41
SHIELD - REMOVAL, REAR
WHEELHOUSE SPLASH................23-41
SHIELDS - DESCRIPTION, HEAT..........11-8
SHIELDS - INSTALLATION, HEAT.........11-8
SHIELDS - REMOVAL, HEAT.............11-8
SHIFT BOOT - INSTALLATION, 4WD
FLOOR
.............................23-62
SHIFT BOOT - REMOVAL, 4WD FLOOR
....23-62
SHIFT COVER - INSTALLATION
....21-129,21-87
SHIFT COVER - REMOVAL
.......21-129,21-87
SHIFT INTERLOCK - ADJUSTMENTS,
BRAKE TRANSMISSION
........21-196,21-365SHIFT INTERLOCK - DIAGNOSIS AND
TESTING, BRAKE TRANSMISSION......21-196,
21-364
SHIFT INTERLOCK SYSTEM -
DESCRIPTION, BRAKE TRANSMISSION . . 21-196,
21-364
SHIFT INTERLOCK SYSTEM -
OPERATION, BRAKE TRANSMISSION....21-196,
21-364
SHIFT LEVER - ADJUSTMENT....21-446,21-481
SHIFT LEVER - INSTALLATION . . . 21-445,21-480
SHIFT LEVER - INSTALLATION, GEAR.....19-12
SHIFT LEVER - REMOVAL.......21-444,21-479
SHIFT LEVER - REMOVAL, GEAR........19-12
SHIFT MECHANISM - DESCRIPTION....21-252,
21-398
SHIFT MECHANISM - INSTALLATION.....21-87
SHIFT MECHANISM - OPERATION......21-252,
21-398
SHIFT MECHANISM - REMOVAL.........21-86
SHIFT MOTOR - DESCRIPTION . . 21-511,21-541,
21-575
SHIFT MOTOR - INSTALLATION . . 21-511,21-541,
21-575
SHIFT MOTOR - OPERATION....21-511,21-541,
21-575
SHIFT MOTOR - REMOVAL.....21-511,21-541,
21-575
SHOCK - DIAGNOSIS AND TESTING . . . 2-24,2-38
SHOCK - DIAGNOSIS AND TESTING,
SPRING.............................2-41
SHOCK - INSTALLATION.............2-38,2-43
SHOCK - REMOVAL................2-38,2-43
SHOES - ADJUSTMENT, PARKING BRAKE . . 5-41
SHOES - INSTALLATION................5-40
SHOES - REMOVAL....................5-39
SIDE - INSTALLATION, LEFT............9-123
SIDE - INSTALLATION, RIGHT...........9-123
SIDE - REMOVAL, LEFT................9-122
SIDE - REMOVAL, RIGHT..............9-122
SIDE BEZEL - INSTALLATION,
INSTRUMENT PANEL DRIVER...........23-58
SIDE BEZEL - REMOVAL, INSTRUMENT
PANEL DRIVER......................23-58
SIDE CURTAIN AIRBAG - DESCRIPTION . . . 8O-56
SIDE CURTAIN AIRBAG - INSTALLATION . . 8O-58
SIDE CURTAIN AIRBAG - OPERATION....8O-56
SIDE CURTAIN AIRBAG - REMOVAL......8O-57
SIDE IMPACT SENSOR - DESCRIPTION . . . 8O-59
SIDE IMPACT SENSOR - OPERATION.....8O-59
SIDE MOLDINGS - INSTALLATION, BODY . . 23-36
SIDE MOLDINGS - REMOVAL, BODY.....23-36
SIDE VIEW MIRROR - INSTALLATION.....23-42
SIDE VIEW MIRROR - REMOVAL........23-41
SIDE VIEW MIRROR FLAG -
INSTALLATION.......................23-27
SIDE VIEW MIRROR FLAG - REMOVAL . . . 23-27
SIDE VIEW MIRROR GLASS -
INSTALLATION.......................23-43
SIDE VIEW MIRROR GLASS - REMOVAL . . 23-42
SIDEVIEW MIRROR - REMOVAL.........8N-12
SIGNAL INDICATOR - DESCRIPTION,
TURN..............................8J-40
SIGNAL INDICATOR - OPERATION, TURN . . 8J-41
SIGNAL LAMP - INSTALLATION,
PARK/TURN.........................8L-21
SIGNAL LAMP - REMOVAL, PARK/TURN . . 8L-21
SIGNAL SYSTEM - DESCRIPTION, TURN . . 8L-18
SIGNAL SYSTEM - OPERATION, TURN....8L-18
SILL TRIM COVER - INSTALLATION,
REAR DOOR........................23-71
SILL TRIM COVER - REMOVAL, REAR
DOOR.............................23-71
SIZE, SPARE WHEEL WITH MATCHING
TIRE - DESCRIPTION, FULL............22-15
SKID PLATE - INSTALLATION, FRONT.....13-23
SKID PLATE - INSTALLATION, TRANSFER
CASE..............................13-26
SKID PLATE - REMOVAL, FRONT........13-23
SKID PLATE - REMOVAL, TRANSFER
CASE..............................13-26
SLEEVE - INSTALLATION, HEADREST.....23-81
SLEEVE - REMOVAL, HEADREST
........23-81
SMOKE DIAGNOSIS CHARTS -
DIAGNOSIS AND TESTING
.............9-236
SNAP RINGS - ASSEMBLY, WITH
.........3-12
SNAP RINGS - DISASSEMBLY, WITH
......3-10
SOLENOID - DESCRIPTION
............21-252
30 INDEXDR
Description Group-Page Description Group-Page Description Group-Page