1998 DODGE RAM 1500 Speed sensor

OPERATION
OPERATION
The Powertrain Control Module (PCM) monitors
many different circuits in the fuel injection, ignition,
emission and engine systems. If the PCM senses a
problem with a monitored circuit often enough to
indicate an actual problem, it stores a Diagnostic
Trouble Code (DTC) in the PCM's memory. If the
problem is repaired or ceases to exist, the PCM can-
cels the code after 40 warm-up cycles. Diagnostic
trouble codes that affect vehicle emissions illuminate
the Malfunction Indicator Lamp (MIL). The MIL is
displayed as an engine icon (graphic) on the instru-
ment panel. Refer to Malfunction Indicator Lamp in
this section.
Certain criteria must be met before the PCM
stores a DTC in memory. The criteria may be a spe-
cific range of engine RPM, engine temperature,
and/or input voltage to the PCM.
The PCM might not store a DTC for a monitored
circuit even though a malfunction has occurred. This
may happen because one of the DTC criteria for the
circuit has not been met.For example,assume the
diagnostic trouble code criteria requires the PCM to
monitor the circuit only when the engine operates
between 750 and 2000 RPM. Suppose the sensor's
output circuit shorts to ground when engine operates
above 2400 RPM (resulting in 0 volt input to the
PCM). Because the condition happens at an engine
speed above the maximum threshold (2000 rpm), the
PCM will not store a DTC.
There are several operating conditions for which
the PCM monitors and sets DTC's. Refer to Moni-
tored Systems, Components, and Non-Monitored Cir-
cuits in this section.
Technicians must retrieve stored DTC's by connect-
ing the DRB scan tool (or an equivalent scan tool) to
the 16±way data link connector. The connector is
located on the bottom edge of the instrument panel
near the steering column (Fig. 1).
NOTE: Various diagnostic procedures may actually
cause a diagnostic monitor to set a DTC. For
instance, pulling a spark plug wire to perform a
spark test may set the misfire code. When a repair
is completed and verified, connect the DRB scan
tool to the 16±way data link connector to erase all
DTC's and extinguish the MIL.
OPERATION - TASK MANAGER
The Task Manager determines which tests happen
when and which functions occur when. Many of the
diagnostic steps required by OBD II must be per-
formed under specific operating conditions. The TaskManager software organizes and prioritizes the diag-
nostic procedures. The job of the Task Manager is to
determine if conditions are appropriate for tests to be
run, monitor the parameters for a trip for each test,
and record the results of the test. Following are the
responsibilities of the Task Manager software:
²Test Sequence
²MIL Illumination
²Diagnostic Trouble Codes (DTCs)
²Trip Indicator
²Freeze Frame Data Storage
²Similar Conditions Window
Test Sequence
In many instances, emissions systems must fail
diagnostic tests more than once before the PCM illu-
minates the MIL. These tests are know as 'two trip
monitors.' Other tests that turn the MIL lamp on
after a single failure are known as 'one trip moni-
tors.' A trip is defined as 'start the vehicle and oper-
ate it to meet the criteria necessary to run the given
monitor.'
Many of the diagnostic tests must be performed
under certain operating conditions. However, there
are times when tests cannot be run because another
test is in progress (conflict), another test has failed
(pending) or the Task Manager has set a fault that
may cause a failure of the test (suspend).
²Pending
Under some situations the Task Manager will not
run a monitor if the MIL is illuminated and a fault is
stored from another monitor. In these situations, the
Task Manager postpones monitorspendingresolu-
tion of the original fault. The Task Manager does not
run the test until the problem is remedied.
Fig. 1 DATA LINK CONNECTOR LOCATION - TYPICAL
1 - 16-WAY DATA LINK CONNECTOR
DREMISSIONS CONTROL 25 - 5
EMISSIONS CONTROL (Continued)

FRONT SERVO - DESCRIPTION.........21-208
FRONT SERVO - DISASSEMBLY........21-209
FRONT SERVO - INSPECTION..........21-209
FRONT SERVO - OPERATION..........21-208
FRONT SKID PLATE - INSTALLATION.....13-23
FRONT SKID PLATE - REMOVAL.........13-23
FRONT SUSPENSION - DESCRIPTION,
GEAR - INDEPENDENT................19-17
FRONT SUSPENSION - INSTALLATION,
GEAR - INDEPENDENT................19-18
FRONT SUSPENSION - REMOVAL, GEAR
- INDEPENDENT.....................19-17
FRONT SUSPENSION, SPECIAL TOOLS....2-12
FRONT TOW HOOK ASSEMBLY -
INSTALLATION.......................13-23
FRONT TOW HOOK ASSEMBLY -
REMOVAL..........................13-23
FRONT WHEEL SPEED SENSOR -
DESCRIPTION........................5-47
FRONT WHEEL SPEED SENSOR -
INSTALLATION........................5-48
FRONT WHEEL SPEED SENSOR -
OPERATION..........................5-47
FRONT WHEEL SPEED SENSOR -
REMOVAL...........................5-48
FRONT WHEELHOUSE SPLASH SHIELD -
INSTALLATION.......................23-41
FRONT WHEELHOUSE SPLASH SHIELD -
REMOVAL..........................23-41
FUEL CONTROL ACTUATOR -
DESCRIPTION.......................14-74
FUEL CONTROL ACTUATOR -
OPERATION.........................14-74
FUEL CONTROL ACTUATOR - REMOVAL . . . 14-74
FUEL DELIVERY - GAS - DESCRIPTION....14-1
FUEL DELIVERY - GAS - OPERATION......14-2
FUEL DRAIN CIRCUIT - OPERATION......14-67
FUEL FILL DOOR - INSTALLATION.......23-39
FUEL FILL DOOR - REMOVAL...........23-39
FUEL FILLER CAP - DESCRIPTION.......25-13
FUEL FILLER CAP - OPERATION.........25-13
FUEL FILTER - STANDARD
PROCEDURES, WATER DRAINING AT.....14-47
FUEL FILTER / WATER SEPARATOR -
DESCRIPTION.......................14-50
FUEL FILTER / WATER SEPARATOR -
INSTALLATION.......................14-50
FUEL FILTER / WATER SEPARATOR -
OPERATION.........................14-50
FUEL FILTER / WATER SEPARATOR -
REMOVAL..........................14-50
FUEL FILTER/PRESSURE REGULATOR -
DESCRIPTION........................14-5
FUEL FILTER/PRESSURE REGULATOR -
OPERATION..........................14-6
FUEL GAUGE - DESCRIPTION...........8J-26
FUEL GAUGE - OPERATION.............8J-26
FUEL HEATER - DESCRIPTION..........14-51
FUEL HEATER - DIAGNOSIS AND
TESTING...........................14-52
FUEL HEATER - OPERATION............14-51
FUEL HEATER RELAY - DESCRIPTION....14-52
FUEL HEATER RELAY - INSTALLATION....14-53
FUEL HEATER RELAY - OPERATION......14-52
FUEL HEATER RELAY - REMOVAL........14-52
FUEL INDICATOR - DESCRIPTION, LOW . . . 8J-30
FUEL INDICATOR - OPERATION, LOW.....8J-30
FUEL INJECTION PUMP - DESCRIPTION . . 14-53
FUEL INJECTION PUMP - INSTALLATION . . 14-55
FUEL INJECTION PUMP - OPERATION....14-53
FUEL INJECTION PUMP - REMOVAL......14-54
FUEL INJECTION PUMP TIMING -
DIAGNOSIS AND TESTING.............14-53
FUEL INJECTOR - DESCRIPTION....14-26,14-74
FUEL INJECTOR - INSTALLATION........14-77
FUEL INJECTOR - OPERATION.....14-26,14-74
FUEL INJECTOR - REMOVAL............14-75
FUEL INJECTOR FIRING ORDER, DIESEL . . 14-48
FUEL INJECTOR RAIL - DESCRIPTION....14-78
FUEL INJECTOR RAIL - INSTALLATION....14-78
FUEL INJECTOR RAIL - OPERATION
......14-78
FUEL INJECTOR RAIL - REMOVAL
.......14-78
FUEL LEVEL SENDING UNIT / SENSOR -
DESCRIPTION
...................14-57,14-6
FUEL LEVEL SENDING UNIT / SENSOR -
INSTALLATION
........................14-7
FUEL LEVEL SENDING UNIT / SENSOR -
OPERATION
.....................14-57,14-6FUEL LEVEL SENDING UNIT / SENSOR -
REMOVAL...........................14-7
FUEL LINE LEAKS - DIAGNOSIS AND
TESTING, HIGH-PRESSURE.............14-58
FUEL LINES - DESCRIPTION........14-57,14-7
FUEL LINES - INSTALLATION...........14-60
FUEL LINES - OPERATION..............14-57
FUEL LINES - REMOVAL...............14-58
FUEL PRESSURE LIMITING VALVE -
DESCRIPTION.......................14-61
FUEL PRESSURE LIMITING VALVE -
INSTALLATION.......................14-61
FUEL PRESSURE LIMITING VALVE -
OPERATION.........................14-61
FUEL PRESSURE LIMITING VALVE -
REMOVAL..........................14-61
FUEL PRESSURE SENSOR -
DESCRIPTION.......................14-60
FUEL PRESSURE SENSOR -
INSTALLATION.......................14-61
FUEL PRESSURE SENSOR - OPERATION . . 14-60
FUEL PRESSURE SENSOR - REMOVAL....14-60
FUEL PUMP - DESCRIPTION............14-11
FUEL PUMP - OPERATION.............14-11
FUEL PUMP MODULE - DESCRIPTION....14-11
FUEL PUMP MODULE - INSTALLATION . . . 14-12
FUEL PUMP MODULE - OPERATION......14-11
FUEL PUMP MODULE - REMOVAL.......14-12
FUEL PUMP RELAY - DESCRIPTION......14-27
FUEL PUMP RELAY - INSTALLATION.....14-28
FUEL PUMP RELAY - OPERATION........14-27
FUEL PUMP RELAY - REMOVAL.........14-28
FUEL PUMP RELAYS - DIAGNOSIS AND
TESTING, ASD........................8I-5
FUEL RAIL - DESCRIPTION.............14-12
FUEL RAIL - INSTALLATION............14-15
FUEL RAIL - OPERATION...............14-12
FUEL RAIL - REMOVAL................14-13
FUEL REQUIREMENTS - DIESEL ENGINE
- DESCRIPTION........................0-1
FUEL SENSOR - DESCRIPTION, WATER
IN ................................14-66
FUEL SENSOR - OPERATION, WATER IN . . 14-66
FUEL SENSOR - REMOVAL, WATER IN....14-66
FUEL SYSTEM - DESCRIPTION, DIESEL . . . 14-45
FUEL SYSTEM - DIESEL ENGINE -
TORQUE............................14-48
FUEL SYSTEM - EXCEPT DIESEL -
TORQUE............................14-3
FUEL SYSTEM PARTS - STANDARD
PROCEDURES, CLEANING..............14-47
FUEL SYSTEM PRESSURE RELEASE -
STANDARD PROCEDURE................14-2
FUEL SYSTEM PRESSURE,
SPECIFICATIONS......................14-3
FUEL SYSTEM PRIMING - STANDARD
PROCEDURE........................14-47
FUEL SYSTEM, SPECIAL TOOLS..........14-5
FUEL SYSTEM, SPECIAL TOOLS -
DIESEL............................14-49
FUEL TANK - DESCRIPTION............14-17
FUEL TANK - OPERATION..............14-17
FUEL TANK MODULE - DESCRIPTION.....14-63
FUEL TANK MODULE - INSTALLATION....14-64
FUEL TANK MODULE - OPERATION......14-63
FUEL TANK MODULE - REMOVAL........14-63
FUEL TRANSFER PUMP - DESCRIPTION . . 14-64
FUEL TRANSFER PUMP - INSTALLATION . . 14-65
FUEL TRANSFER PUMP - OPERATION....14-64
FUEL TRANSFER PUMP - REMOVAL......14-64
FULL SIZE, SPARE WHEEL WITH
MATCHING TIRE - DESCRIPTION........22-15
FUNCTIONS - DESCRIPTION, CIRCUIT . . 8W-01-6
FUSE - DESCRIPTION, IOD...........8W-97-6
FUSE - INSTALLATION, IOD..........8W-97-7
FUSE - OPERATION, IOD.............8W-97-6
FUSE - REMOVAL, IOD..............8W-97-7
FUSES POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON......8W-01-10
GAP AND FLUSH - SPECIFICATIONS......23-95
GAS ENGINE - DIAGNOSIS AND TESTING
. . 11-4
GAS ENGINE - INSTALLATION
...........19-26
GAS ENGINE - REMOVAL
..............19-25
GAS ENGINES - CLEANING, RADIATOR
FAN
................................7-34
GAS ENGINES - DESCRIPTION, COOLANT
RECOVERY CONTAINER
................7-33GAS ENGINES - INSPECTION, RADIATOR
FAN ................................7-34
GAS ENGINES - INSTALLATION,
COOLANT RECOVERY CONTAINER........7-33
GAS ENGINES - INSTALLATION,
RADIATOR FAN.......................7-34
GAS ENGINES - OPERATION, COOLANT
RECOVERY CONTAINER................7-33
GAS ENGINES - REMOVAL, COOLANT
RECOVERY CONTAINER................7-33
GAS ENGINES - REMOVAL, RADIATOR
FAN ................................7-33
GAS ENGINES - STANDARD
PROCEDURE, DRAINING COOLING
SYSTEM - ALL........................7-17
GAS ENGINES - STANDARD
PROCEDURE, REFILLING COOLING
SYSTEM - ALL........................7-18
GASKET - DIAGNOSIS AND TESTING,
CYLINDER HEAD......................9-21
GASKET FAILURE - DIAGNOSIS AND
TESTING, CYLINDER HEAD.............9-199
GASKET SELECTION - STANDARD
PROCEDURE, HEAD...................9-281
GASKET SURFACE PREPARATION -
STANDARD PROCEDURE, ENGINE........9-10
GASKETS AND SEALERS - STANDARD
PROCEDURE, FORM-IN-PLACE . . . 9-239,9-9,9-94
GAUGE - DESCRIPTION, ENGINE
TEMPERATURE......................8J-24
GAUGE - DESCRIPTION, FUEL...........8J-26
GAUGE - DESCRIPTION, OIL PRESSURE . . 8J-33
GAUGE - DESCRIPTION, VOLTAGE.......8J-42
GAUGE - OPERATION, ENGINE
TEMPERATURE......................8J-24
GAUGE - OPERATION, FUEL............8J-26
GAUGE - OPERATION, OIL PRESSURE....8J-33
GAUGE - OPERATION, VOLTAGE.........8J-43
GAUGES - DIAGNOSIS AND TESTING,
PRESSURE..........................22-7
GAUGES INDICATOR - DESCRIPTION,
CHECK.............................8J-21
GAUGES INDICATOR - OPERATION,
CHECK.............................8J-21
GEAR - DESCRIPTION, CRANKSHAFT.....9-273
GEAR - INDEPENDENT FRONT
SUSPENSION - DESCRIPTION...........19-17
GEAR - INDEPENDENT FRONT
SUSPENSION - INSTALLATION..........19-18
GEAR - INDEPENDENT FRONT
SUSPENSION - REMOVAL..............19-17
GEAR - INSTALLATION................9-273
GEAR - INSTALLATION, PINION
GEAR/RING......................3-51,3-77
GEAR - LINK/COIL - DESCRIPTION.......19-20
GEAR - LINK/COIL - INSTALLATION......19-21
GEAR - LINK/COIL - OPERATION........19-20
GEAR - LINK/COIL - REMOVAL..........19-20
GEAR - REMOVAL....................9-273
GEAR - REMOVAL, PINION GEAR/RING....3-49,
3-75
GEAR HOUSING - INSTALLATION........9-300
GEAR HOUSING - REMOVAL............9-299
GEAR HOUSING COVER - INSTALLATION . . 9-301
GEAR HOUSING COVER - REMOVAL
.....9-301
GEAR INPUT SHAFT SEAL -
INSTALLATION, STEERING
.............19-29
GEAR INPUT SHAFT SEAL - REMOVAL,
STEERING
..........................19-27
GEAR SELECTOR INDICATOR -
DESCRIPTION
.......................8J-27
GEAR SELECTOR INDICATOR -
OPERATION
.........................8J-27
GEAR SHIFT LEVER - INSTALLATION
.....19-12
GEAR SHIFT LEVER - REMOVAL
.........19-12
GEAR, SPECIAL TOOLS - POWER
STEERING
..........................19-23
GEAR, SPECIFICATIONS - POWER
STEERING
..........................19-22
GEAR TO COOLER - INSTALLATION,
RETURN HOSE
.................19-44,19-45
GEAR TO COOLER - REMOVAL, RETURN
HOSE
.........................19-44,19-45
GEAR/RING GEAR - INSTALLATION,
PINION
.........................3-51,3-77
GEAR/RING GEAR - REMOVAL, PINION
....3-49,
3-75
14 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

HEATED SEAT MODULE - INSTALLATION . . . 8E-7
HEATED SEAT MODULE - INSTALLATION . . 8G-15
HEATED SEAT MODULE - OPERATION.....8E-6
HEATED SEAT MODULE - OPERATION....8G-14
HEATED SEAT MODULE - REMOVAL.......8E-7
HEATED SEAT MODULE - REMOVAL.....8G-15
HEATED SEAT SENSOR - DESCRIPTION . . . 8G-11
HEATED SEAT SENSOR - DIAGNOSIS
AND TESTING.......................8G-11
HEATED SEAT SENSOR - OPERATION....8G-11
HEATED SEAT SENSOR - REMOVAL......8G-11
HEATED SEAT SWITCH - DESCRIPTION . . . 8G-11
HEATED SEAT SWITCH - DIAGNOSIS
AND TESTING.......................8G-12
HEATED SEAT SWITCH - INSTALLATION . . 8G-13
HEATED SEAT SWITCH - OPERATION.....8G-12
HEATED SEAT SWITCH - REMOVAL......8G-13
HEATED SEAT SYSTEM - DESCRIPTION....8G-7
HEATED SEAT SYSTEM - DIAGNOSIS
AND TESTING........................8G-8
HEATED SEAT SYSTEM - OPERATION.....8G-8
HEATER - 5.9L DIESEL - DESCRIPTION,
ENGINE BLOCK.......................7-37
HEATER - 5.9L DIESEL - INSTALLATION,
ENGINE BLOCK.......................7-38
HEATER - 5.9L DIESEL - OPERATION,
ENGINE BLOCK.......................7-38
HEATER - 5.9L DIESEL - REMOVAL,
ENGINE BLOCK.........................7-38
HEATER - DESCRIPTION, ENGINE BLOCK . . . 7-36
HEATER - DESCRIPTION, FUEL..........14-51
HEATER - DESCRIPTION, INTAKE AIR.....14-80
HEATER - DIAGNOSIS AND TESTING,
ENGINE BLOCK.......................7-36
HEATER - DIAGNOSIS AND TESTING,
FUEL..............................14-52
HEATER - INSTALLATION, ENGINE
BLOCK..............................7-37
HEATER - INSTALLATION, INTAKE AIR....14-80
HEATER - OPERATION, ENGINE BLOCK....7-36
HEATER - OPERATION, FUEL............14-51
HEATER - OPERATION, INTAKE AIR......14-80
HEATER - REMOVAL, ENGINE BLOCK......7-37
HEATER - REMOVAL, INTAKE AIR........14-80
HEATER AND AIR CONDITIONER -
DESCRIPTION........................24-1
HEATER AND AIR CONDITIONER -
OPERATION..........................24-1
HEATER CONTROL - DESCRIPTION, A/C . . . 24-14
HEATER CONTROL - INSTALLATION, A/C . . 24-15
HEATER CONTROL - REMOVAL, A/C......24-15
HEATER CORE - DESCRIPTION..........24-63
HEATER CORE - INSTALLATION.........24-63
HEATER CORE - OPERATION............24-63
HEATER CORE - REMOVAL.............24-63
HEATER INLET HOSE - INSTALLATION....24-64
HEATER INLET HOSE - REMOVAL........24-64
HEATER PERFORMANCE TEST -
DIAGNOSIS AND TESTING..............24-6
HEATER RELAY - DESCRIPTION, FUEL....14-52
HEATER RELAY - DESCRIPTION, INTAKE
AIR ...............................14-82
HEATER RELAY - INSTALLATION, FUEL . . . 14-53
HEATER RELAY - INSTALLATION, INTAKE
AIR ...............................14-82
HEATER RELAY - OPERATION, FUEL......14-52
HEATER RELAY - OPERATION, INTAKE
AIR ...............................14-82
HEATER RELAY - REMOVAL, FUEL.......14-52
HEATER RELAY - REMOVAL, INTAKE AIR . . 14-82
HEATER RETURN HOSE - INSTALLATION . . 24-65
HEATER RETURN HOSE - REMOVAL......24-64
HEIGHT ADJUSTMENT - 4WD (LD) -
STANDARD PROCEDURE.................2-3
HEIGHT MEASUREMENT - 4WD (LD) -
STANDARD PROCEDURE.................2-3
HEMI ENGINE - INSTALLATION, 3.7L/4.7L
AND 5.7L......................24-59,24-73
HEMI ENGINE - REMOVAL, 3.7L/4.7L
AND 5.7L......................24-57,24-71
HIGH BEAM INDICATOR - DESCRIPTION
. . 8J-28
HIGH BEAM INDICATOR - OPERATION
....8J-28
HIGH MOUNTED STOP LAMP -
INSTALLATION, CENTER
...............8L-11
HIGH MOUNTED STOP LAMP -
REMOVAL, CENTER
...................8L-11
HIGH MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER
...............8L-11HIGH MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER...................8L-11
HIGH PRESSURE RELIEF VALVE -
DESCRIPTION.......................24-48
HIGH PRESSURE RELIEF VALVE -
OPERATION.........................24-48
HIGH SPEEDS - DESCRIPTION, TIRE
PRESSURE..........................22-7
HIGH/LOW RELAY - DESCRIPTION,
WIPER.............................8R-20
HIGH/LOW RELAY - DIAGNOSIS AND
TESTING, WIPER.....................8R-21
HIGH/LOW RELAY - INSTALLATION,
WIPER.............................8R-22
HIGH/LOW RELAY - OPERATION, WIPER . . 8R-20
HIGH/LOW RELAY - REMOVAL, WIPER . . . 8R-21
HIGH-PRESSURE FUEL LINE LEAKS -
DIAGNOSIS AND TESTING.............14-58
HINGE - INSTALLATION.....23-16,23-22,23-31,
23-46
HINGE - INSTALLATION, CENTER SEAT
BACK..............................23-79
HINGE - REMOVAL....23-16,23-22,23-31,23-46
HINGE - REMOVAL, CENTER SEAT BACK . . 23-78
HINGE COVER - INSTALLATION, CENTER
SEAT BACK INERTIA..................23-77
HINGE COVER - REMOVAL, CENTER
SEAT BACK INERTIA..................23-77
HITCH - INSTALLATION, TRAILER........13-25
HITCH - REMOVAL, TRAILER...........13-25
HOAT COOLANT - DESCRIPTION..........7-32
HOISTING - STANDARD PROCEDURE......0-20
HOLDDOWN - DESCRIPTION, BATTERY . . . 8F-14
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-14
HOLDDOWN - OPERATION, BATTERY.....8F-14
HOLDDOWN - REMOVAL, BATTERY......8F-14
HOLDER - INSTALLATION, CUP.........23-51
HOLDER - REMOVAL, CUP.............23-51
HOLDING CLUTCHES - DESCRIPTION....21-371
HOLDING CLUTCHES - OPERATION.....21-372
HOLE PLUG - INSTALLATION, CAMSHAFT
CORE..............................9-206
HOLE PLUG - REMOVAL, CAMSHAFT
CORE..............................9-205
HOLE REPAIR - DESCRIPTION,
THREADED........................Intro.-8
HONING - STANDARD PROCEDURE,
CYLINDER BORE.................9-128,9-38
HOOD - INSTALLATION................23-47
HOOD - REMOVAL....................23-46
HOOK - INSTALLATION, COAT...........23-66
HOOK - REMOVAL, COAT..............23-66
HOOK ASSEMBLY - INSTALLATION,
FRONT TOW........................13-23
HOOK ASSEMBLY - REMOVAL, FRONT
TOW ..............................13-23
HORN - DIAGNOSIS AND TESTING.......8H-1
HORN - INSTALLATION.................8H-2
HORN - REMOVAL....................8H-2
HORN SWITCH - DESCRIPTION..........8H-2
HORN SWITCH - DIAGNOSIS AND
TESTING............................8H-2
HORN SYSTEM - DESCRIPTION..........8H-1
HORN SYSTEM - DIAGNOSIS AND
TESTING............................8H-1
HORN SYSTEM - OPERATION............8H-1
HOSE - GEAR TO COOLER -
INSTALLATION, RETURN..........19-44,19-45
HOSE - GEAR TO COOLER - REMOVAL,
RETURN......................19-44,19-45
HOSE - INSTALLATION, FRONT BRAKE.....5-13
HOSE - INSTALLATION, HEATER INLET....24-64
HOSE - INSTALLATION, HEATER RETURN . 24-65
HOSE - INSTALLATION, PRESSURE . 19-44,19-45
HOSE - INSTALLATION, REAR BRAKE......5-12
HOSE - REMOVAL, FRONT..............5-12
HOSE - REMOVAL, HEATER INLET.......24-64
HOSE - REMOVAL, HEATER RETURN.....24-64
HOSE - REMOVAL, PRESSURE.....19-44,19-45
HOSE - REMOVAL, REAR BRAKE
.........5-11
HOSE - RESERVOIR TO COOLER -
INSTALLATION, RETURN
..........19-44,19-45
HOSE - RESERVOIR TO COOLER -
REMOVAL, RETURN
.............19-44,19-45
HOSE ASSEMBLY - INSTALLATION, REAR
TUBE
...............................5-13
HOSE ASSEMBLY - REMOVAL, REAR
TUBE
...............................5-12HOSE CLAMPS - DESCRIPTION...........7-3
HOSE CLAMPS - OPERATION.............7-5
HOSES/TUBES - DESCRIPTION, WASHER . 8R-11
HOSES/TUBES - OPERATION, WASHER . . . 8R-11
HOUSING - ASSEMBLY, HVAC...........24-35
HOUSING - DIAGNOSIS AND TESTING,
CLUTCH..............................6-7
HOUSING - DISASSEMBLY, HVAC........24-35
HOUSING - INSTALLATION, CLUTCH.......6-9
HOUSING - INSTALLATION, GEAR........9-300
HOUSING - INSTALLATION, HVAC........24-36
HOUSING - INSTALLATION, ROCKER.....9-255
HOUSING - REMOVAL, CLUTCH...........6-9
HOUSING - REMOVAL, GEAR...........9-299
HOUSING - REMOVAL, HVAC...........24-34
HOUSING - REMOVAL, ROCKER.........9-255
HOUSING BUSHING AND SEAL -
INSTALLATION, EXTENSION...........21-440
HOUSING BUSHING AND SEAL -
REMOVAL, EXTENSION...............21-440
HOUSING COVER - INSTALLATION, GEAR . 9-301
HOUSING COVER - REMOVAL, GEAR.....9-301
HOUSING FLUID LEAK - DIAGNOSIS AND
TESTING, CONVERTER.........21-144,21-318
HOUSING SEAL - INSTALLATION,
ADAPTER...............21-128,21-364,21-85
HOUSING SEAL - INSTALLATION,
EXTENSION . 21-128,21-201,21-507,21-536,21-85
HOUSING SEAL - REMOVAL, ADAPTER . . 21-128,
21-364,21-85
HOUSING SEAL - REMOVAL,
EXTENSION . 21-128,21-201,21-507,21-536,21-85
HOUSING SEAL AND DUST BOOT -
INSTALLATION, EXTENSION.....21-476,21-571
HOUSING SEAL AND DUST BOOT -
REMOVAL, EXTENSION.........21-476,21-571
HOW TO USE WIRING DIAGRAMS -
DESCRIPTION.....................8W-01-1
H-SECTION REPLACEMENT - STANDARD
PROCEDURE, REAR FRAME............13-13
HUB / BEARING - INSTALLATION.........2-32
HUB / BEARING - REMOVAL.............2-31
HVAC HOUSING - ASSEMBLY...........24-35
HVAC HOUSING - DISASSEMBLY........24-35
HVAC HOUSING - INSTALLATION........24-36
HVAC HOUSING - REMOVAL............24-34
HYDRAULIC BOOSTER - DIAGNOSIS
AND TESTING........................5-30
HYDRAULIC LASH ADJUSTER -
DIAGNOSIS AND TESTING.........9-125,9-32
HYDRAULIC PRESSURE TEST -
DIAGNOSIS AND TESTING......21-141,21-316
HYDRAULIC SCHEMATICS, SCHEMATICS
AND DIAGRAMS..............21-176,21-337
HYDRAULIC TAPPETS - DIAGNOSIS AND
TESTING...........................9-210
HYDRAULIC TAPPETS - INSTALLATION . . . 9-211
HYDRAULIC TAPPETS - REMOVAL.......9-211
HYDROBOOST - INSTALLATION..........5-27
HYDROBOOST - INSTALLATION, ALL
EXCEPT.............................5-27
HYDROBOOST - REMOVAL..............5-26
HYDROBOOST - REMOVAL, ALL EXCEPT . . . 5-26
HYDRO-BOOST BRAKE BOOSTER -
INSTALLATION........................5-32
HYDRO-BOOST BRAKE BOOSTER -
REMOVAL
...........................5-31
HYDROFORM FENDER RAIL REPAIR -
STANDARD PROCEDURE
...............13-11
HYDROSTATIC LOCK - STANDARD
PROCEDURE
...................9-190,9-240
IDENTIFICATION - DESCRIPTION,
FASTENER
.........................Intro.-5
IDENTIFICATION AND INFORMATION -
DESCRIPTION, SECTION
.............8W-01-6
IDENTIFICATION NUMBER -
DESCRIPTION, VEHICLE
..............Intro.-1
IDLE AIR CONTROL MOTOR -
DESCRIPTION
.......................14-28
IDLE AIR CONTROL MOTOR -
INSTALLATION
.......................14-29
IDLE AIR CONTROL MOTOR -
OPERATION
.........................14-28
IDLE AIR CONTROL MOTOR - REMOVAL
. . 14-29
IDLER SHAFT - INSTALLATION
......9-179,9-81
IDLER SHAFT - REMOVAL
..........9-179,9-81
IGNITION - SPECIFICATIONS, TORQUE
.....8I-3
16 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

IGNITION CIRCUIT SENSE -
DESCRIPTION.......................8E-10
IGNITION CIRCUIT SENSE - OPERATION . . 8E-11
IGNITION COIL - DESCRIPTION..........8I-11
IGNITION COIL - INSTALLATION.........8I-14
IGNITION COIL - OPERATION............8I-12
IGNITION COIL - REMOVAL.............8I-13
IGNITION COIL CAPACITOR -
DESCRIPTION........................8I-21
IGNITION COIL CAPACITOR -
INSTALLATION.......................8I-21
IGNITION COIL CAPACITOR - OPERATION . . 8I-21
IGNITION COIL CAPACITOR - REMOVAL . . . 8I-21
IGNITION COIL RESISTANCE, 3.7L V-6.....8I-5
IGNITION COIL RESISTANCE, 4.7L V-8.....8I-5
IGNITION COIL RESISTANCE, 5.7L V-8.....8I-5
IGNITION CONTROL - DESCRIPTION.......8I-1
IGNITION SWITCH - DESCRIPTION........19-9
IGNITION SWITCH - DESCRIPTION,
KEY-IN.............................19-11
IGNITION SWITCH - DIAGNOSIS AND
TESTING............................19-9
IGNITION SWITCH - INSTALLATION......19-11
IGNITION SWITCH - OPERATION.........19-9
IGNITION SWITCH - REMOVAL..........19-10
IGNITION SWITCH AND KEY LOCK
CYLINDER - DIAGNOSIS AND TESTING . . . 19-11
IGNITION TIMING, SPECIFICATIONS.......8I-5
IGNITION-OFF DRAW TEST - STANDARD
PROCEDURE........................8F-11
IMMOBILIZER MODULE - DESCRIPTION,
SENTRY KEY........................8E-13
IMMOBILIZER MODULE - INSTALLATION,
SENTRY KEY........................8E-15
IMMOBILIZER MODULE - OPERATION,
SENTRY KEY........................8E-13
IMMOBILIZER MODULE - REMOVAL,
SENTRY KEY........................8E-15
IMMOBILIZER MODULE (SKIM) -
DESCRIPTION, SENTRY KEY.............8Q-1
IMMOBILIZER MODULE (SKIM) -
OPERATION, SENTRY KEY..............8Q-2
IMMOBILIZER SYSTEM INDICATOR
LAMP - DESCRIPTION, SENTRY KEY......8Q-5
IMMOBILIZER SYSTEM INDICATOR
LAMP - OPERATION, SENTRY KEY........8Q-5
IMMOBILIZER SYSTEM INITIALIZATION,
STANDARD PROCEDURE - SENTRY
KEY................................8Q-3
IMMOBILIZER SYSTEM (SKIS) -
DESCRIPTION, SENTRY KEY.............8Q-1
IMMOBILIZER SYSTEM (SKIS) -
OPERATION, SENTRY KEY..............8Q-2
IMMOBILIZER SYSTEM TRANSPONDER
PROGRAMMING, STANDARD
PROCEDURE - SENTRY KEY.............8Q-4
IMPACT SENSOR - DESCRIPTION, SIDE . . 8O-59
IMPACT SENSOR - OPERATION, SIDE....8O-59
INCORRECT FLUID LEVEL - DIAGNOSIS
AND TESTING, EFFECTS OF......21-201,21-366
INDEPENDENT FRONT SUSPENSION -
DESCRIPTION, GEAR..................19-17
INDEPENDENT FRONT SUSPENSION -
INSTALLATION, GEAR.................19-18
INDEPENDENT FRONT SUSPENSION -
REMOVAL, GEAR.....................19-17
INDICATOR - DESCRIPTION, ABS........8J-17
INDICATOR - DESCRIPTION, AIRBAG.....8J-18
INDICATOR - DESCRIPTION, BRAKE/
PARK BRAKE........................8J-19
INDICATOR - DESCRIPTION, CARGO
LAMP
..............................8J-20
INDICATOR - DESCRIPTION, CHECK
GAUGES
............................8J-21
INDICATOR - DESCRIPTION, CRUISE
.....8J-22
INDICATOR - DESCRIPTION, DOOR AJAR
. . 8J-23
INDICATOR - DESCRIPTION, ETC
........8J-25
INDICATOR - DESCRIPTION, GEAR
SELECTOR
..........................8J-27
INDICATOR - DESCRIPTION, HIGH BEAM
. . 8J-28
INDICATOR - DESCRIPTION, LAMP OUT
. . . 8J-29
INDICATOR - DESCRIPTION, LOW FUEL
. . . 8J-30
INDICATOR - DESCRIPTION, SEATBELT
. . . 8J-34
INDICATOR - DESCRIPTION, SECURITY
. . . 8J-35
INDICATOR - DESCRIPTION, SERVICE
4WD
...............................8J-36
INDICATOR - DESCRIPTION, TOW/HAUL
. . . 8J-39INDICATOR - DESCRIPTION, TRANS
TEMP..............................8J-40
INDICATOR - DESCRIPTION, TURN
SIGNAL............................8J-40
INDICATOR - DESCRIPTION, UPSHIFT....8J-41
INDICATOR - DESCRIPTION, WAIT-TO-
START .............................8J-44
INDICATOR - DESCRIPTION, WASHER
FLUID..............................8J-44
INDICATOR - DESCRIPTION, WATER-IN-
FUEL..............................8J-45
INDICATOR - DIAGNOSIS AND TESTING,
BRAKE.............................8J-20
INDICATOR - OPERATION, ABS..........8J-17
INDICATOR - OPERATION, AIRBAG.......8J-18
INDICATOR - OPERATION, BRAKE/PARK
BRAKE.............................8J-19
INDICATOR - OPERATION, CARGO LAMP . . 8J-20
INDICATOR - OPERATION, CHECK
GAUGES............................8J-21
INDICATOR - OPERATION, CRUISE.......8J-22
INDICATOR - OPERATION, DOOR AJAR . . . 8J-23
INDICATOR - OPERATION, ETC..........8J-25
INDICATOR - OPERATION, GEAR
SELECTOR..........................8J-27
INDICATOR - OPERATION, HIGH BEAM....8J-28
INDICATOR - OPERATION, LAMP OUT....8J-29
INDICATOR - OPERATION, LOW FUEL.....8J-30
INDICATOR - OPERATION, SEATBELT.....8J-34
INDICATOR - OPERATION, SECURITY......8J-36
INDICATOR - OPERATION, SERVICE 4WD . . 8J-37
INDICATOR - OPERATION, TOW/HAUL....8J-39
INDICATOR - OPERATION, TRANS TEMP . . 8J-40
INDICATOR - OPERATION, TURN SIGNAL . . 8J-41
INDICATOR - OPERATION, UPSHIFT......8J-42
INDICATOR - OPERATION, WAIT-TO-
START .............................8J-44
INDICATOR - OPERATION, WASHER
FLUID..............................8J-44
INDICATOR - OPERATION, WATER-IN-
FUEL..............................8J-45
INDICATOR LAMP - DESCRIPTION,
SENTRY KEY IMMOBILIZER SYSTEM......8Q-5
INDICATOR LAMP - OPERATION,
SENTRY KEY IMMOBILIZER SYSTEM......8Q-5
INDICATOR LAMP (MIL) - DESCRIPTION,
MALFUNCTION.......................8J-31
INDICATOR LAMP (MIL) - OPERATION,
MALFUNCTION.......................8J-31
INDICATOR TEST - STANDARD
PROCEDURE, BUILT-IN................8F-10
INDICATORS - DIAGNOSIS AND
TESTING, TREAD WEAR................22-8
INERTIA HINGE COVER - INSTALLATION,
CENTER SEAT BACK..................23-77
INERTIA HINGE COVER - REMOVAL,
CENTER SEAT BACK..................23-77
INFLATION PRESSURES - DESCRIPTION,
TIRE................................22-7
INFO CENTER - DESCRIPTION,
ELECTRONIC VEHICLE.................8M-7
INFO CENTER - INSTALLATION,
ELECTRONIC VEHICLE.................8M-9
INFO CENTER - OPERATION,
ELECTRONIC VEHICLE.................8M-7
INFO CENTER - REMOVAL, ELECTRONIC
VEHICLE............................8M-9
INITIAL OPERATION - STANDARD
PROCEDURE, POWER STEERING
PUMP.............................19-40
INITIALIZATION, STANDARD PROCEDURE
- SENTRY KEY IMMOBILIZER SYSTEM....8Q-3
INJECTED RINGS - ASSEMBLY, WITH......3-13
INJECTED RINGS - DISASSEMBLY, WITH . . . 3-11
INJECTION PUMP - DESCRIPTION, FUEL . . 14-53
INJECTION PUMP - INSTALLATION, FUEL . 14-55
INJECTION PUMP - OPERATION, FUEL....14-53
INJECTION PUMP - REMOVAL, FUEL.....14-54
INJECTION PUMP TIMING - DIAGNOSIS
AND TESTING, FUEL..................14-53
INJECTOR - DESCRIPTION, FUEL . . . 14-26,14-74
INJECTOR - INSTALLATION, FUEL........14-77
INJECTOR - OPERATION, FUEL
.....14-26,14-74
INJECTOR - REMOVAL, FUEL
...........14-75
INJECTOR FIRING ORDER, DIESEL -
FUEL
..............................14-48
INJECTOR RAIL - DESCRIPTION, FUEL
....14-78
INJECTOR RAIL - INSTALLATION, FUEL
. . . 14-78INJECTOR RAIL - OPERATION, FUEL.....14-78
INJECTOR RAIL - REMOVAL, FUEL.......14-78
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - DESCRIPTION.....14-79
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - INSTALLATION.....14-79
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - OPERATION.......14-79
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - REMOVAL........14-79
INLET FILTER - INSTALLATION..........14-20
INLET FILTER - REMOVAL..............14-20
INLET HOSE - INSTALLATION, HEATER....24-64
INLET HOSE - REMOVAL, HEATER.......24-64
INNER BELT MOLDING - INSTALLATION,
FRONT DOOR.......................23-93
INNER BELT MOLDING - INSTALLATION,
REAR DOOR........................23-94
INNER BELT MOLDING - REMOVAL,
FRONT DOOR.......................23-93
INNER BELT MOLDING - REMOVAL,
REAR DOOR........................23-94
INPUT - OPERATION, ASD SENSE - PCM . . . 8I-5
INPUT CLUTCH ASSEMBLY - ASSEMBLY . 21-378
INPUT CLUTCH ASSEMBLY -
DESCRIPTION......................21-373
INPUT CLUTCH ASSEMBLY -
DISASSEMBLY......................21-374
INPUT CLUTCH ASSEMBLY - OPERATION . 21-373
INPUT SHAFT SEAL - INSTALLATION,
STEERING GEAR.......................19-29
INPUT SHAFT SEAL - REMOVAL,
STEERING GEAR.....................19-27
INPUT SPEED SENSOR - DESCRIPTION . . 21-382
INPUT SPEED SENSOR - INSTALLATION . 21-382
INPUT SPEED SENSOR - OPERATION....21-382
INPUT SPEED SENSOR - REMOVAL.....21-382
INSERTS - INSTALLATION, SPRING TIP....2-45
INSERTS - REMOVAL, SPRING TIP........2-44
INSIDE HANDLE ACTUATOR -
INSTALLATION..................23-22,23-32
INSIDE HANDLE ACTUATOR - REMOVAL . . 23-22,
23-31
INSTRUMENT CLUSTER - ASSEMBLY.....8J-15
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-2
INSTRUMENT CLUSTER - DIAGNOSIS
AND TESTING.......................8J-10
INSTRUMENT CLUSTER - DISASSEMBLY . . 8J-14
INSTRUMENT CLUSTER - INSTALLATION . . 8J-16
INSTRUMENT CLUSTER - OPERATION.....8J-6
INSTRUMENT CLUSTER - REMOVAL.....8J-14
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-7
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-7
INSTRUMENT PANEL ASSEMBLY -
INSTALLATION.......................23-55
INSTRUMENT PANEL ASSEMBLY -
REMOVAL..........................23-52
INSTRUMENT PANEL CENTER BEZEL -
INSTALLATION.......................23-57
INSTRUMENT PANEL CENTER BEZEL -
REMOVAL..........................23-57
INSTRUMENT PANEL DEMISTER DUCTS
- INSTALLATION.....................24-37
INSTRUMENT PANEL DEMISTER DUCTS
- REMOVAL.........................24-36
INSTRUMENT PANEL DRIVER SIDE
BEZEL - INSTALLATION................23-58
INSTRUMENT PANEL DRIVER SIDE
BEZEL - REMOVAL...................23-58
INSTRUMENT PANEL DUCTS -
INSTALLATION.......................24-37
INSTRUMENT PANEL DUCTS - REMOVAL . 24-37
INSTRUMENT PANEL HEADLAMP
SWITCH BEZEL - INSTALLATION.........23-56
INSTRUMENT PANEL HEADLAMP
SWITCH BEZEL - REMOVAL............23-56
INSTRUMENT PANEL LOWER
SURROUND - INSTALLATION...........23-59
INSTRUMENT PANEL LOWER
SURROUND - REMOVAL
...............23-59
INSTRUMENT PANEL TOP COVER -
INSTALLATION
.......................23-59
INSTRUMENT PANEL TOP COVER -
REMOVAL
..........................23-58
INTAKE AIR HEATER - DESCRIPTION
.....14-80
INTAKE AIR HEATER - INSTALLATION
.....14-80
DRINDEX 17
Description Group-Page Description Group-Page Description Group-Page

OUTER TIE ROD END - REMOVAL.......19-32
OUTLET - DESCRIPTION, CIGAR
LIGHTER.........................8W-97-2
OUTLET - DESCRIPTION, POWER......8W-97-7
OUTLET - DIAGNOSIS AND TESTING,
CIGAR LIGHTER...................8W-97-2
OUTLET - DIAGNOSIS AND TESTING,
POWER..........................8W-97-7
OUTLET - INSTALLATION, POWER.....8W-97-8
OUTLET - OPERATION, CIGAR LIGHTER . 8W-97-2
OUTLET - OPERATION, POWER.......8W-97-7
OUTLET - REMOVAL, POWER.........8W-97-8
OUTLETS - DESCRIPTION, AIR..........24-26
OUTLETS - INSTALLATION, AIR.........24-27
OUTLETS - REMOVAL, AIR.............24-26
OUTPUT - DESCRIPTION, PCM...........8I-5
OUTPUT - OPERATION, PCM............14-27
OUTPUT - OPERATION, PCM.............8I-5
OUTPUT SHAFT FRONT BEARING -
INSTALLATION......................21-216
OUTPUT SHAFT FRONT BEARING -
REMOVAL.........................21-216
OUTPUT SHAFT REAR BEARING -
INSTALLATION......................21-217
OUTPUT SHAFT REAR BEARING -
REMOVAL.........................21-216
OUTPUT SHAFT SEAL - INSTALLATION,
FRONT....21-442,21-477,21-508,21-538,21-572
OUTPUT SHAFT SEAL - REMOVAL,
FRONT.....21-441,21-477,21-507,21-537,21-572
OUTPUT SPEED SENSOR - DESCRIPTION . 21-391
OUTPUT SPEED SENSOR -
INSTALLATION......................21-392
OUTPUT SPEED SENSOR - OPERATION . . 21-391
OUTPUT SPEED SENSOR - REMOVAL . . . 21-391
OVERDRIVE CLUTCH - DESCRIPTION....21-217
OVERDRIVE CLUTCH - OPERATION.....21-217
OVERDRIVE ELECTRICAL CONTROLS -
DIAGNOSIS AND TESTING............21-262
OVERDRIVE SWITCH - DESCRIPTION,
TOW/HAUL..................21-261,21-392
OVERDRIVE SWITCH - INSTALLATION,
TOW/HAUL..................21-262,21-393
OVERDRIVE SWITCH - OPERATION,
TOW/HAUL..................21-262,21-392
OVERDRIVE SWITCH - REMOVAL,
TOW/HAUL..................21-262,21-392
OVERDRIVE UNIT - ASSEMBLY.........21-226
OVERDRIVE UNIT - CLEANING.........21-225
OVERDRIVE UNIT - DISASSEMBLY......21-218
OVERDRIVE UNIT - INSPECTION.......21-225
OVERDRIVE UNIT - INSTALLATION......21-235
OVERDRIVE UNIT - REMOVAL.........21-218
OVERFLOW VALVE - DESCRIPTION,
CASCADE...........................14-66
OVERFLOW VALVE - OPERATION,
CASCADE...........................14-66
OVERHEAD CONSOLE - DESCRIPTION....8M-1
OVERHEAD CONSOLE - DIAGNOSIS AND
TESTING............................8M-2
OVERHEAD CONSOLE - OPERATION......8M-2
OVERHEAD CONSOLE REMOVAL,
REMOVAL
...........................8M-6
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
ASSEMBLY
.........................21-237
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
CLEANING
.........................21-236
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
DESCRIPTION
......................21-236
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
DISASSEMBLY
......................21-236
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
INSPECTION
.......................21-237
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
OPERATION
........................21-236
OXYGEN SENSOR - DESCRIPTION
.......14-35
OXYGEN SENSOR - INSTALLATION
.......14-36
OXYGEN SENSOR - REMOVAL
..........14-35
PAINT CODE - DESCRIPTION
...........23-73
PAINT CODES - SPECIFICATIONS
........23-73
PAINT TOUCH-UP - DESCRIPTION
.......23-74PAINT TOUCH-UP - STANDARD
PROCEDURE........................23-74
PAN - CLEANING, OIL.............9-293,9-66
PAN - DESCRIPTION, OIL...............9-66
PAN - INSPECTION, OIL...........9-293,9-66
PAN - INSTALLATION, OIL . . . 9-155,9-224,9-293,
9-66
PAN - REMOVAL, OIL . . . 9-155,9-224,9-293,9-66
PANEL - INSTALLATION, TRIM.....23-24,23-33
PANEL - REMOVAL, TRIM.........23-24,23-33
PANEL ANTENNA CABLE -
INSTALLATION, INSTRUMENT............8A-7
PANEL ANTENNA CABLE - REMOVAL,
INSTRUMENT........................8A-7
PANEL ASSEMBLY - INSTALLATION,
INSTRUMENT.......................23-55
PANEL ASSEMBLY - REMOVAL,
INSTRUMENT.......................23-52
PANEL CENTER BEZEL - INSTALLATION,
INSTRUMENT.......................23-57
PANEL CENTER BEZEL - REMOVAL,
INSTRUMENT.......................23-57
PANEL DEMISTER DUCTS -
INSTALLATION, INSTRUMENT...........24-37
PANEL DEMISTER DUCTS - REMOVAL,
INSTRUMENT.......................24-36
PANEL DRIVER SIDE BEZEL -
INSTALLATION, INSTRUMENT...........23-58
PANEL DRIVER SIDE BEZEL - REMOVAL,
INSTRUMENT.......................23-58
PANEL DUCTS - INSTALLATION,
INSTRUMENT.........................24-37
PANEL DUCTS - REMOVAL,
INSTRUMENT.......................24-37
PANEL HEADLAMP SWITCH BEZEL -
INSTALLATION, INSTRUMENT...........23-56
PANEL HEADLAMP SWITCH BEZEL -
REMOVAL, INSTRUMENT..............23-56
PANEL LOWER SURROUND -
INSTALLATION, INSTRUMENT...........23-59
PANEL LOWER SURROUND - REMOVAL,
INSTRUMENT.......................23-59
PANEL REPAIR - STANDARD
PROCEDURE, PLASTIC BODY............23-3
PANEL TOP COVER - INSTALLATION,
INSTRUMENT.......................23-59
PANEL TOP COVER - REMOVAL,
INSTRUMENT.......................23-58
PANEL TRIM - INSTALLATION, REAR
CAB BACK..........................23-69
PANEL TRIM - REMOVAL, REAR CAB
BACK..............................23-68
PARK BRAKE CABLE - INSTALLATION,
REAR...............................5-38
PARK BRAKE CABLE - REMOVAL, REAR . . . 5-37
PARK LAMP RELAY - DESCRIPTION......8L-20
PARK LAMP RELAY - DIAGNOSIS AND
TESTING...........................8L-20
PARK LAMP RELAY - INSTALLATION.....8L-21
PARK LAMP RELAY - OPERATION.......8L-20
PARK LAMP RELAY - REMOVAL.........8L-21
PARKING BRAKE - DESCRIPTION.........5-36
PARKING BRAKE - OPERATION...........5-36
PARKING BRAKE CABLE -
INSTALLATION, FRONT.................5-38
PARKING BRAKE CABLE - REMOVAL,
FRONT..............................5-36
PARKING BRAKE SHOES - ADJUSTMENT
. . . 5-41
PARK/TURN SIGNAL LAMP -
INSTALLATION
.......................8L-21
PARK/TURN SIGNAL LAMP - REMOVAL
. . . 8L-21
PARTS - STANDARD PROCEDURES,
CLEANING FUEL SYSTEM
..............14-47
PASSENGER AIRBAG - DESCRIPTION
....8O-39
PASSENGER AIRBAG - INSTALLATION
....8O-41
PASSENGER AIRBAG - OPERATION
......8O-40
PASSENGER AIRBAG - REMOVAL
........8O-40
PASSENGER AIRBAG ON/OFF SWITCH -
DESCRIPTION
.......................8O-42
PASSENGER AIRBAG ON/OFF SWITCH -
INSTALLATION
......................8O-44
PASSENGER AIRBAG ON/OFF SWITCH -
OPERATION
.........................8O-43
PASSENGER AIRBAG ON/OFF SWITCH -
REMOVAL
..........................8O-43
PASSENGER SEAT SWITCH -
DESCRIPTION
.......................8N-15PASSENGER SEAT SWITCH - DIAGNOSIS
AND TESTING.......................8N-16
PASSENGER SEAT SWITCH -
INSTALLATION......................8N-16
PASSENGER SEAT SWITCH - OPERATION . 8N-15
PASSENGER SEAT SWITCH - REMOVAL . . . 8N-16
PATTERNS - DIAGNOSIS AND TESTING,
TIRE WEAR..........................22-8
PCM - DESCRIPTION...................8E-7
PCM - OPERATION...................8E-10
PCM INPUT - OPERATION, ASD SENSE.....8I-5
PCM OUTPUT - DESCRIPTION............8I-5
PCM OUTPUT - OPERATION............14-27
PCM OUTPUT - OPERATION.............8I-5
PCM/SKIM PROGRAMMING - STANDARD
PROCEDURE........................8E-14
PCV VALVE - 3.7L V-6/ 4.7L V-8 -
DIAGNOSIS AND TESTING.............25-20
PCV VALVE - DESCRIPTION............25-17
PCV VALVE - INSTALLATION............25-21
PCV VALVE - OPERATION..............25-19
PCV VALVE - REMOVAL...............25-21
PEDAL - DESCRIPTION.................5-28
PEDAL - INSTALLATION............5-28,5-42
PEDAL - INSTALLATION, ACCELERATOR . . . 14-21
PEDAL - OPERATION...................5-28
PEDAL - REMOVAL................5-28,5-42
PEDAL - REMOVAL, ACCELERATOR........14-21
PEDAL MOTOR - DESCRIPTION,
ADJUSTABLE..........................5-6
PEDAL MOTOR - INSTALLATION,
ADJUSTABLE..........................5-7
PEDAL MOTOR - REMOVAL,
ADJUSTABLE..........................5-7
PEDAL POSITION SENSOR -
DESCRIPTION, ACCELERATOR.....14-22,14-68
PEDAL POSITION SENSOR -
INSTALLATION, ACCELERATOR.....14-22,14-71
PEDAL POSITION SENSOR - OPERATION,
ACCELERATOR.................14-22,14-68
PEDAL POSITION SENSOR - REMOVAL,
ACCELERATOR.................14-22,14-68
PEDAL POSITION SWITCH -
DESCRIPTION, CLUTCH.................6-13
PEDAL POSITION SWITCH - DIAGNOSIS
AND TESTING, CLUTCH.................6-13
PEDAL POSITION SWITCH - OPERATION,
CLUTCH.............................6-13
PEDAL SWITCH - INSTALLATION,
ADJUSTABLE..........................5-6
PEDAL SWITCH - REMOVAL,
ADJUSTABLE..........................5-6
PER MILE, SPECIFICATIONS - TIRE
REVOLUTIONS.......................22-10
PERFORMANCE - DIAGNOSIS AND
TESTING, A/C........................24-3
PERFORMANCE - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS . . . 9-183,9-4,9-90
PERFORMANCE TEST - DIAGNOSIS AND
TESTING, HEATER.....................24-6
PILOT BEARING - INSTALLATION.........6-12
PILOT BEARING - REMOVAL.............6-11
PINION GEAR/RING GEAR -
INSTALLATION....................3-51,3-77
PINION GEAR/RING GEAR - REMOVAL . 3-49,3-75
PINION GEAR/RING GEAR/TONE RING -
INSTALLATION.............3-108,3-137,3-164
PINION GEAR/RING GEAR/TONE RING -
REMOVAL................3-106,3-134,3-162
PINION SEAL - INSTALLATION . 3-126,3-154,3-45,
3-71,3-96
PINION SEAL - REMOVAL....3-126,3-153,3-44,
3-70,3-95
PIPE - INSPECTION, EXHAUST.......11-7,11-8
PISTON & CONNECTING ROD -
CLEANING.....................9-140,9-212
PISTON & CONNECTING ROD -
DESCRIPTION.........9-139,9-211,9-281,9-48
PISTON & CONNECTING ROD -
INSPECTION
...................9-140,9-213
PISTON & CONNECTING ROD -
INSTALLATION
..................9-140,9-213
PISTON & CONNECTING ROD -
REMOVAL
................9-139,9-212,9-281
PISTON AND CONNECTING ROD -
CLEANING
..........................9-282
PISTON FITTING - STANDARD
PROCEDURE
...............9-139,9-211,9-51
DRINDEX 23
Description Group-Page Description Group-Page Description Group-Page

PISTON RETAINER - ASSEMBLY,
OVERRUNNING CLUTCH CAM/
OVERDRIVE........................21-237
PISTON RETAINER - CLEANING,
OVERRUNNING CLUTCH CAM/
OVERDRIVE........................21-236
PISTON RETAINER - DESCRIPTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE........................21-236
PISTON RETAINER - DISASSEMBLY,
OVERRUNNING CLUTCH CAM/
OVERDRIVE........................21-236
PISTON RETAINER - INSPECTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE........................21-237
PISTON RETAINER - OPERATION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE........................21-236
PISTON RING FITTING - STANDARD
PROCEDURE..........9-142,9-213,9-284,9-53
PISTONS - DESCRIPTION.......21-239,21-393
PISTONS - INSPECTION...............9-282
PISTONS - OPERATION.........21-239,21-393
PITMAN ARM - INSTALLATION..........19-37
PITMAN ARM - REMOVAL.............19-36
PLANETARY GEARTRAIN - ASSEMBLY . . . 21-397
PLANETARY GEARTRAIN - CLEANING....21-396
PLANETARY GEARTRAIN - DESCRIPTION . 21-395
PLANETARY GEARTRAIN -
DISASSEMBLY......................21-396
PLANETARY GEARTRAIN - INSPECTION . . 21-397
PLANETARY GEARTRAIN - OPERATION . . 21-396
PLANETARY GEARTRAIN/OUTPUT SHAFT
- ASSEMBLY.......................21-244
PLANETARY GEARTRAIN/OUTPUT SHAFT
- DESCRIPTION.....................21-241
PLANETARY GEARTRAIN/OUTPUT SHAFT
- DISASSEMBLY....................21-242
PLANETARY GEARTRAIN/OUTPUT SHAFT
- INSPECTION......................21-243
PLANETARY GEARTRAIN/OUTPUT SHAFT
- OPERATION.......................21-241
PLASTIC BODY PANEL REPAIR -
STANDARD PROCEDURE................23-3
PLATE - DESCRIPTION, BODY CODE....Intro.-3
PLATE - DESCRIPTION, ENGINE DATA....9-248
PLATE - INSTALLATION, FLEX . . 9-138,9-210,9-48
PLATE - INSTALLATION, FRONT SKID.....13-23
PLATE - INSTALLATION, SUPPORT........5-36
PLATE - INSTALLATION, TRANSFER
CASE SKID.........................13-26
PLATE - REMOVAL, FLEX.....9-138,9-210,9-48
PLATE - REMOVAL, FRONT SKID........13-23
PLATE - REMOVAL, SUPPORT...........5-35
PLATE - REMOVAL, TRANSFER CASE
SKID..............................13-26
PLATE LAMP - INSTALLATION, LICENSE . . 8L-17
PLATE LAMP - REMOVAL, LICENSE......8L-17
PLATE LAMP UNIT - INSTALLATION,
LICENSE...........................8L-17
PLATE LAMP UNIT - REMOVAL, LICENSE . . 8L-17
PLATES - INSTALLATION, EXTERIOR
NAME.............................23-38
PLATES - REMOVAL, EXTERIOR NAME....23-38
PLUG - DESCRIPTION, SPARK...........8I-17
PLUG - INSTALLATION, CAMSHAFT
CORE HOLE.........................9-206
PLUG - REMOVAL, CAMSHAFT CORE
HOLE..............................9-205
PLUG - REMOVAL, SPARK
..............8I-19
PLUG CABLE - DESCRIPTION, SPARK
.....8I-21
PLUG CABLE - INSTALLATION, SPARK
....8I-22
PLUG CABLE - OPERATION, SPARK
.......8I-21
PLUG CABLE - REMOVAL, SPARK
........8I-22
PLUG CABLE RESISTANCE,
SPECIFICATIONS - SPARK
...............8I-4
PLUG CONDITIONS - DIAGNOSIS AND
TESTING, SPARK
.....................8I-17
PLUGS - INSTALLATION, CORE
..........9-131
PLUGS - REMOVAL, CORE
.............9-131
PLUGS, SPECIFICATIONS - SPARK
........8I-4
PLUMBING - CLEANING, CHARGE AIR
COOLER
............................11-17
PLUMBING - DESCRIPTION, CHARGE
AIR COOLER
........................11-16
PLUMBING - INSPECTION, CHARGE AIR
COOLER
............................11-17PLUMBING - INSTALLATION, CHARGE
AIR COOLER........................11-17
PLUMBING - OPERATION, CHARGE AIR
COOLER............................11-16
PLUMBING - REMOVAL, CHARGE AIR
COOLER............................11-17
PLY TIRES - DESCRIPTION, RADIAL.......22-6
POLISHING - DESCRIPTION, FINESSE
SANDING/BUFFING...................23-74
PORT VALVE CORE - DESCRIPTION,
SERVICE...........................24-70
PORT VALVE CORE - INSTALLATION,
SERVICE...........................24-70
PORT VALVE CORES - REMOVAL,
SERVICE...........................24-70
POSITION SENSOR - DESCRIPTION.....21-442,
21-477
POSITION SENSOR - DESCRIPTION,
ACCELERATOR PEDAL............14-22,14-68
POSITION SENSOR - DESCRIPTION,
CAMSHAFT.........................14-71
POSITION SENSOR - DESCRIPTION,
CAMSHAFT...........................8I-7
POSITION SENSOR - DESCRIPTION,
CRANKSHAFT..................14-23,14-72
POSITION SENSOR - DESCRIPTION,
THROTTLE..........................14-41
POSITION SENSOR - INSTALLATION....21-443,
21-478
POSITION SENSOR - INSTALLATION,
ACCELERATOR PEDAL............14-22,14-71
POSITION SENSOR - INSTALLATION,
CAMSHAFT.........................14-72
POSITION SENSOR - INSTALLATION,
CAMSHAFT..........................8I-10
POSITION SENSOR - INSTALLATION,
CRANKSHAFT..................14-25,14-73
POSITION SENSOR - INSTALLATION,
THROTTLE..........................14-43
POSITION SENSOR - OPERATION . 21-442,21-477
POSITION SENSOR - OPERATION,
ACCELERATOR PEDAL............14-22,14-68
POSITION SENSOR - OPERATION,
CAMSHAFT.........................14-71
POSITION SENSOR - OPERATION,
CAMSHAFT...........................8I-7
POSITION SENSOR - OPERATION,
CRANKSHAFT..................14-23,14-72
POSITION SENSOR - OPERATION,
THROTTLE..........................14-41
POSITION SENSOR - REMOVAL . . 21-443,21-478
POSITION SENSOR - REMOVAL,
ACCELERATOR PEDAL............14-22,14-68
POSITION SENSOR - REMOVAL,
CAMSHAFT.........................14-72
POSITION SENSOR - REMOVAL,
CAMSHAFT...........................8I-9
POSITION SENSOR - REMOVAL,
CRANKSHAFT..................14-24,14-73
POSITION SENSOR - REMOVAL,
THROTTLE..........................14-41
POSITION SWITCH - DESCRIPTION,
CLUTCH PEDAL.......................6-13
POSITION SWITCH - DIAGNOSIS AND
TESTING, CLUTCH PEDAL...............6-13
POSITION SWITCH - OPERATION,
CLUTCH PEDAL.......................6-13
POTENTIAL - STANDARD PROCEDURE,
TESTING OF VOLTAGE..............8W-01-9
POWER - INSTALLATION, WINDOW
REGULATOR...................23-26,23-34
POWER - REMOVAL, WINDOW
REGULATOR...................23-25,23-34
POWER BRAKE BOOSTER -
DESCRIPTION........................5-29
POWER BRAKE BOOSTER -
INSTALLATION........................5-29
POWER BRAKE BOOSTER - OPERATION . . . 5-29
POWER BRAKE BOOSTER - REMOVAL.....5-29
POWER DISTRIBUTION - DESCRIPTION . 8W-97-1
POWER DISTRIBUTION - OPERATION . . 8W-97-1
POWER DISTRIBUTION SYSTEMS,
SPECIAL TOOLS
...................8W-97-2
POWER GROUNDS - DESCRIPTION
......8E-10
POWER LOCK SWITCH - DIAGNOSIS
AND TESTING
........................8N-4
POWER LOCK SWITCH - INSTALLATION
. . . 8N-4
POWER LOCK SWITCH - REMOVAL
.......8N-4POWER LOCKS - DESCRIPTION..........8N-1
POWER LOCKS - DIAGNOSIS AND
TESTING............................8N-3
POWER LOCKS - OPERATION............8N-2
POWER MIRROR SWITCH - DIAGNOSIS
AND TESTING.......................8N-12
POWER MIRROR SWITCH - REMOVAL . . . 8N-12
POWER MIRRORS - DESCRIPTION......8N-10
POWER MIRRORS - DIAGNOSIS AND
TESTING...........................8N-10
POWER MIRRORS - OPERATION........8N-10
POWER MODULE - DESCRIPTION,
INTEGRATED......................8W-97-3
POWER MODULE - INSTALLATION,
INTEGRATED......................8W-97-4
POWER MODULE - OPERATION,
INTEGRATED......................8W-97-3
POWER MODULE - REMOVAL,
INTEGRATED......................8W-97-3
POWER OUTLET - DESCRIPTION......8W-97-7
POWER OUTLET - DIAGNOSIS AND
TESTING.........................8W-97-7
POWER OUTLET - INSTALLATION.....8W-97-8
POWER OUTLET - OPERATION........8W-97-7
POWER OUTLET - REMOVAL.........8W-97-8
POWER SEAT SYSTEM - DIAGNOSIS
AND TESTING.......................8N-13
POWER SEAT TRACK - DESCRIPTION....8N-16
POWER SEAT TRACK - DIAGNOSIS AND
TESTING...........................8N-17
POWER SEAT TRACK - INSTALLATION....8N-17
POWER SEAT TRACK - OPERATION......8N-16
POWER SEAT TRACK - REMOVAL.......8N-17
POWER SEATS - DESCRIPTION.........8N-13
POWER SEATS - OPERATION...........8N-13
POWER STEERING FLOW AND
PRESSURE - DIAGNOSIS AND
TESTING............................19-4
POWER STEERING FLUID -
DESCRIPTION.........................0-3
POWER STEERING FLUID LEVEL
CHECKING - STANDARD PROCEDURE....19-43
POWER STEERING GEAR, SPECIAL
TOOLS.............................19-23
POWER STEERING GEAR,
SPECIFICATIONS.....................19-22
POWER STEERING PRESSURE SWITCH -
DESCRIPTION.......................19-46
POWER STEERING PRESSURE SWITCH -
OPERATION.........................19-46
POWER STEERING PUMP - INITIAL
OPERATION - STANDARD PROCEDURE . . . 19-40
POWER STEERING SYSTEM -
DIAGNOSIS AND TESTING..............19-2
POWER STEERING SYSTEM -
STANDARD PROCEDURE, FLUSHING.....19-40
POWER WINDOWS - DESCRIPTION......8N-19
POWER WINDOWS - DIAGNOSIS AND
TESTING...........................8N-19
POWER WINDOWS - OPERATION........8N-19
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON FUSES . 8W-01-10
PRE-ALIGNMENT INSPECTION -
DIAGNOSIS AND TESTING...............2-2
PRESSURE - DIAGNOSIS AND TESTING,
CHECKING ENGINE OIL.......9-152,9-220,9-65
PRESSURE - DIAGNOSIS AND TESTING,
CYLINDER COMPRESSION......9-186,9-8,9-93
PRESSURE - DIAGNOSIS AND TESTING,
ENGINE OIL.........................9-289
PRESSURE - DIAGNOSIS AND TESTING,
POWER STEERING FLOW...............19-4
PRESSURE - DIAGNOSIS AND TESTING,
TURBOCHARGER BOOST...............11-11
PRESSURE BLEEDING - STANDARD
PROCEDURE..........................5-5
PRESSURE CAP - DESCRIPTION,
RADIATOR...........................7-57
PRESSURE CAP - OPERATION,
RADIATOR...........................7-58
PRESSURE FOR HIGH SPEEDS -
DESCRIPTION, TIRE
...................22-7
PRESSURE GAUGE - DESCRIPTION, OIL
. . 8J-33
PRESSURE GAUGE - OPERATION, OIL
....8J-33
PRESSURE GAUGES - DIAGNOSIS AND
TESTING
............................22-7
PRESSURE HOSE - INSTALLATION
. . 19-44,19-45
24 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

RAIL - DESCRIPTION, FUEL INJECTOR....14-78
RAIL - INSTALLATION, FUEL............14-15
RAIL - INSTALLATION, FUEL INJECTOR . . . 14-78
RAIL - OPERATION, FUEL..............14-12
RAIL - OPERATION, FUEL INJECTOR.....14-78
RAIL - REMOVAL, FUEL...............14-13
RAIL - REMOVAL, FUEL INJECTOR.......14-78
RAIL REPAIR - STANDARD PROCEDURE,
HYDROFORM FENDER.................13-11
RAIL TIP REPLACEMENT - STANDARD
PROCEDURE, LIGHT DUTY FRONT
FRAME..............................13-4
RAIL WEATHERSTRIP - INSTALLATION,
DRIP..............................23-91
RAIL WEATHERSTRIP - REMOVAL, DRIP . . 23-91
RAIL WEATHERSTRIP RETAINER -
INSTALLATION, DRIP.................23-92
RAIL WEATHERSTRIP RETAINER -
REMOVAL, DRIP.....................23-92
RANGE SENSOR - DESCRIPTION,
TRANSMISSION...............21-263,21-405
RANGE SENSOR - INSTALLATION,
TRANSMISSION.....................21-266
RANGE SENSOR - OPERATION,
TRANSMISSION...............21-263,21-405
RANGE SENSOR - REMOVAL,
TRANSMISSION.....................21-265
RANGE SENSOR (TRS) - DIAGNOSIS
AND TESTING, TRANSMISSION........21-264
RATINGS, SPECIFICATIONS -
GENERATOR........................8F-20
RE TRANSMISSION, SPECIAL TOOLS....21-191
READING LAMP - DESCRIPTION.........8L-28
READING LAMP - INSTALLATION........8L-29
READING LAMP - OPERATION..........8L-28
READING LAMP - REMOVAL............8L-28
READING/COURTESY LAMP
REPLACEMENT - STANDARD
PROCEDURE.........................8M-3
REAR AXLE - 10 1/2 AA -
ADJUSTMENTS......................3-116
REAR AXLE - 10 1/2 AA - DIAGNOSIS
AND TESTING.......................3-112
REAR AXLE - 10 1/2 AA - INSTALLATION . . 3-116
REAR AXLE - 10 1/2 AA - REMOVAL.....3-115
REAR AXLE - 10 1/2 AA - SPECIAL
TOOLS.............................3-120
REAR AXLE - 10 1/2 AA -
SPECIFICATIONS.....................3-120
REAR AXLE - 11 1/2 AA -
ADJUSTMENTS......................3-144
REAR AXLE - 11 1/2 AA - DIAGNOSIS
AND TESTING.......................3-140
REAR AXLE - 11 1/2 AA - INSTALLATION . . 3-144
REAR AXLE - 11 1/2 AA - REMOVAL.....3-143
REAR AXLE - 11 1/2 AA - SPECIAL
TOOLS.............................3-148
REAR AXLE - 11 1/2 AA -
SPECIFICATIONS.....................3-148
REAR AXLE - 9 1/4 - ADJUSTMENTS......3-83
REAR AXLE - 9 1/4 - DIAGNOSIS AND
TESTING............................3-80
REAR AXLE - 9 1/4 - INSTALLATION......3-83
REAR AXLE - 9 1/4 - REMOVAL..........3-83
REAR AXLE - 9 1/4 - SPECIAL TOOLS.....3-90
REAR AXLE - 9 1/4 - SPECIFICATIONS.....3-90
REAR BEARING - INSTALLATION,
OUTPUT SHAFT.....................21-217
REAR BEARING - REMOVAL, OUTPUT
SHAFT............................21-216
REAR BRAKE HOSE - INSTALLATION......5-12
REAR BRAKE HOSE - REMOVAL..........5-11
REAR BUMPER - INSTALLATION..........13-4
REAR BUMPER - REMOVAL.............13-3
REAR CAB BACK PANEL TRIM -
INSTALLATION.......................23-69
REAR CAB BACK PANEL TRIM -
REMOVAL..........................23-68
REAR CABLE - INSTALLATION, LEFT......5-39
REAR CABLE - INSTALLATION, RIGHT.....5-38
REAR CABLE - REMOVAL, LEFT..........5-38
REAR CABLE - REMOVAL, RIGHT
.........5-37
REAR CENTER SEAT BELT &
RETRACTOR - INSTALLATION
...........8O-45
REAR CENTER SEAT BELT &
RETRACTOR - REMOVAL
..............8O-44
REAR CLUTCH - ASSEMBLY
...........21-249
REAR CLUTCH - CLEANING
...........21-248REAR CLUTCH - DESCRIPTION.........21-247
REAR CLUTCH - DISASSEMBLY........21-248
REAR CLUTCH - INSPECTION..........21-248
REAR CLUTCH - OPERATION..........21-248
REAR DOOR GLASS RUN
WEATHERSTRIP - INSTALLATION........23-93
REAR DOOR GLASS RUN
WEATHERSTRIP - REMOVAL............23-93
REAR DOOR INNER BELT MOLDING -
INSTALLATION.......................23-94
REAR DOOR INNER BELT MOLDING -
REMOVAL..........................23-94
REAR DOOR OUTER BELT MOLDING -
INSTALLATION.......................23-94
REAR DOOR OUTER BELT MOLDING -
REMOVAL..........................23-93
REAR DOOR SILL TRIM COVER -
INSTALLATION.......................23-71
REAR DOOR SILL TRIM COVER -
REMOVAL..........................23-71
REAR DRUM IN HAT BRAKE - CLEANING . . . 5-39
REAR DRUM IN HAT BRAKE -
INSPECTION.........................5-39
REAR DUAL WHEELS - INSTALLATION.....5-35
REAR DUAL WHEELS - REMOVAL........5-34
REAR FENDER - INSTALLATION.........23-44
REAR FENDER - REMOVAL.............23-44
REAR FRAME H-SECTION REPLACEMENT
- STANDARD PROCEDURE.............13-13
REAR MOUNT - INSTALLATION....9-149,9-220,
9-288,9-61
REAR MOUNT - REMOVAL . . . 9-149,9-220,9-288,
9-61
REAR OIL SEAL RETAINER -
INSTALLATION, CRANKSHAFT......9-210,9-277
REAR OIL SEAL RETAINER - REMOVAL,
CRANKSHAFT..................9-209,9-277
REAR OUTBOARD SEAT BELT &
RETRACTOR - INSTALLATION...........8O-47
REAR OUTBOARD SEAT BELT &
RETRACTOR - REMOVAL..............8O-46
REAR PARK BRAKE CABLE -
INSTALLATION........................5-38
REAR PARK BRAKE CABLE - REMOVAL....5-37
REAR PROPELLER SHAFT -
INSTALLATION.........................3-8
REAR PROPELLER SHAFT - REMOVAL......3-8
REAR SEAL AREA LEAKS - DIAGNOSIS
AND TESTING..............9-137,9-209,9-65
REAR SERVO - ASSEMBLY............21-251
REAR SERVO - CLEANING............21-251
REAR SERVO - DESCRIPTION..........21-251
REAR SERVO - DISASSEMBLY.........21-251
REAR SERVO - OPERATION...........21-251
REAR TUBE / HOSE ASSEMBLY -
INSTALLATION........................5-13
REAR TUBE / HOSE ASSEMBLY -
REMOVAL...........................5-12
REAR VIEW MIRROR - REMOVAL........23-69
REAR VIEW MIRROR SUPPORT
BRACKET - INSTALLATION.............23-70
REAR WHEEL ANTILOCK - DIAGNOSIS
AND TESTING
........................5-48
REAR WHEEL INSTALLATION -
STANDARD PROCEDURE, DUAL
.........22-12
REAR WHEEL SPEED SENSOR -
DIAGNOSIS AND TESTING
..............5-49
REAR WHEEL SPEED SENSOR -
INSTALLATION
........................5-48
REAR WHEEL SPEED SENSOR -
REMOVAL
...........................5-48
REAR WHEELHOUSE SPLASH SHIELD -
INSTALLATION
.......................23-41
REAR WHEELHOUSE SPLASH SHIELD -
REMOVAL
..........................23-41
REAR WINDOW DEFOGGER RELAY -
DESCRIPTION
........................8G-2
REAR WINDOW DEFOGGER RELAY -
INSTALLATION
.......................8G-4
REAR WINDOW DEFOGGER RELAY -
OPERATION
..........................8G-3
REAR WINDOW DEFOGGER RELAY -
REMOVAL
...........................8G-3
REAR WINDOW DEFOGGER SWITCH -
DESCRIPTION
........................8G-4
REAR WINDOW DEFOGGER SWITCH -
OPERATION
..........................8G-4REAR WINDOW DEFOGGER SYSTEM -
DIAGNOSIS AND TESTING..............8G-2
RECEIVER - INSTALLATION, ASH........23-51
RECEIVER - REMOVAL, ASH............23-50
RECIRCULATION DOOR - INSTALLATION . . 24-40
RECIRCULATION DOOR - REMOVAL......24-39
RECIRCULATION DOOR ACTUATOR -
DESCRIPTION.......................24-24
RECIRCULATION DOOR ACTUATOR -
INSTALLATION.......................24-25
RECIRCULATION DOOR ACTUATOR -
OPERATION.........................24-24
RECIRCULATION DOOR ACTUATOR -
REMOVAL..........................24-24
RECOVERY - STANDARD PROCEDURE,
REFRIGERANT.......................24-47
RECOVERY CONTAINER- GAS ENGINES -
DESCRIPTION, COOLANT...............7-33
RECOVERY CONTAINER- GAS ENGINES -
INSTALLATION, COOLANT...............7-33
RECOVERY CONTAINER- GAS ENGINES -
OPERATION, COOLANT.................7-33
RECOVERY CONTAINER- GAS ENGINES -
REMOVAL, COOLANT..................7-33
REDUCER - DESCRIPTION, SEAT BELT
TENSION...........................8O-53
REDUCER - DIAGNOSIS AND TESTING,
SEAT BELT TENSION..................8O-54
REDUCER - OPERATION, SEAT BELT
TENSION...........................8O-54
REFACING - STANDARD PROCEDURE . 9-202,9-28
REFACING - STANDARD PROCEDURE,
CYLINDER BLOCK....................9-264
REFILLING COOLING SYSTEM - ALL GAS
ENGINES - STANDARD PROCEDURE......7-18
REFILLING COOLING SYSTEM 5.9L
DIESEL ENGINE - STANDARD
PROCEDURE.........................7-19
REFRIGERANT - DESCRIPTION..........24-67
REFRIGERANT - OPERATION............24-67
REFRIGERANT LINE - DESCRIPTION......24-42
REFRIGERANT LINE COUPLER -
DESCRIPTION.......................24-67
REFRIGERANT LINE COUPLER -
INSTALLATION.......................24-68
REFRIGERANT LINE COUPLER -
OPERATION.........................24-67
REFRIGERANT LINE COUPLER -
REMOVAL..........................24-68
REFRIGERANT LINES - OPERATION......24-42
REFRIGERANT OIL - DESCRIPTION......24-68
REFRIGERANT OIL - OPERATION........24-69
REFRIGERANT OIL LEVEL - STANDARD
PROCEDURE........................24-69
REFRIGERANT RECOVERY - STANDARD
PROCEDURE........................24-47
REFRIGERANT SYSTEM CHARGE -
STANDARD PROCEDURE...............24-47
REFRIGERANT SYSTEM EVACUATE -
STANDARD PROCEDURE...............24-47
REFRIGERANT SYSTEM LEAKS -
DIAGNOSIS AND TESTING.............24-44
REFRIGERANT SYSTEM SERVICE
EQUIPMENT - STANDARD PROCEDURE . . . 24-46
REGULATOR - DESCRIPTION, FUEL
FILTER/PRESSURE.....................14-5
REGULATOR - DESCRIPTION, VOLTAGE . . . 8F-25
REGULATOR - MANUAL - INSTALLATION,
WINDOW......................23-27,23-35
REGULATOR - MANUAL - REMOVAL,
WINDOW......................23-26,23-35
REGULATOR - OPERATION, FUEL
FILTER/PRESSURE.....................14-6
REGULATOR - OPERATION, VOLTAGE.....8F-25
REGULATOR - POWER - INSTALLATION,
WINDOW......................23-26,23-34
REGULATOR - POWER - REMOVAL,
WINDOW......................23-25,23-34
RELAY - DESCRIPTION, A/C
COMPRESSOR CLUTCH...............24-13
RELAY - DESCRIPTION, FOG LAMP......8L-12
RELAY - DESCRIPTION, FUEL HEATER
....14-52
RELAY - DESCRIPTION, FUEL PUMP
.....14-27
RELAY - DESCRIPTION, INTAKE AIR
HEATER
............................14-82
RELAY - DESCRIPTION, PARK LAMP
.....8L-20
RELAY - DESCRIPTION, REAR WINDOW
DEFOGGER
..........................8G-2
26 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

SEAT STORAGE BIN COVERING -
REMOVAL, UNDER...................23-80
SEAT STORAGE BIN LATCH -
INSTALLATION, UNDER................23-80
SEAT STORAGE BIN LATCH - REMOVAL,
UNDER............................23-80
SEAT STORAGE BIN LID -
INSTALLATION, UNDER................23-80
SEAT STORAGE BIN LID - REMOVAL,
UNDER............................23-80
SEAT SWITCH - DESCRIPTION, DRIVER . . . 8N-14
SEAT SWITCH - DESCRIPTION, HEATED . . 8G-11
SEAT SWITCH - DESCRIPTION,
PASSENGER........................8N-15
SEAT SWITCH - DIAGNOSIS AND
TESTING, DRIVER....................8N-14
SEAT SWITCH - DIAGNOSIS AND
TESTING, HEATED....................8G-12
SEAT SWITCH - DIAGNOSIS AND
TESTING, PASSENGER................8N-16
SEAT SWITCH - INSTALLATION, DRIVER . . 8N-15
SEAT SWITCH - INSTALLATION, HEATED . . 8G-13
SEAT SWITCH - INSTALLATION,
PASSENGER........................8N-16
SEAT SWITCH - OPERATION, DRIVER....8N-14
SEAT SWITCH - OPERATION, HEATED....8G-12
SEAT SWITCH - OPERATION,
PASSENGER........................8N-15
SEAT SWITCH - REMOVAL, DRIVER......8N-15
SEAT SWITCH - REMOVAL, HEATED......8G-13
SEAT SWITCH - REMOVAL, PASSENGER....8N-16
SEAT SYSTEM - DESCRIPTION, HEATED . . . 8G-7
SEAT SYSTEM - DIAGNOSIS AND
TESTING, HEATED.....................8G-8
SEAT SYSTEM - DIAGNOSIS AND
TESTING, POWER....................8N-13
SEAT SYSTEM - OPERATION, HEATED.....8G-8
SEAT TRACK - DESCRIPTION, POWER....8N-16
SEAT TRACK - DIAGNOSIS AND
TESTING, POWER....................8N-17
SEAT TRACK - INSTALLATION...........23-83
SEAT TRACK - INSTALLATION, POWER . . . 8N-17
SEAT TRACK - OPERATION, POWER.....8N-16
SEAT TRACK - REMOVAL..............23-83
SEAT TRACK - REMOVAL, POWER.......8N-17
SEATBELT INDICATOR - DESCRIPTION....8J-34
SEATBELT INDICATOR - OPERATION......8J-34
SEATBELT REMINDER PROGRAMMING -
STANDARD PROCEDURE, ENHANCED.....8J-35
SEATS - DESCRIPTION, INTAKE/
EXHAUST VALVES...........9-123,9-256,9-28
SEATS - DESCRIPTION, POWER.........8N-13
SEATS - INSTALLATION, INTAKE/
EXHAUST VALVES................9-124,9-30
SEATS - OPERATION, POWER..........8N-13
SEATS - REMOVAL, INTAKE/EXHAUST
VALVES ........................9-124,9-29
SECONDARY CATCH - INSTALLATION,
LATCH STRIKER.....................23-48
SECONDARY CATCH - REMOVAL, LATCH
STRIKER...........................23-47
SECURITY INDICATOR - DESCRIPTION....8J-35
SECURITY INDICATOR - OPERATION.....8J-36
SECURITY SYSTEM, DIAGNOSIS AND
TESTING - VEHICLE THEFT
..............8Q-3
SELECTION - STANDARD PROCEDURE,
HEAD GASKET
.......................9-281
SELECTOR INDICATOR - DESCRIPTION,
GEAR
..............................8J-27
SELECTOR INDICATOR - OPERATION,
GEAR
..............................8J-27
SELECTOR SWITCH - DESCRIPTION
....21-510,
21-539,21-574
SELECTOR SWITCH - OPERATION
......21-510,
21-540,21-574
SENDING UNIT / SENSOR -
DESCRIPTION, FUEL LEVEL
........14-57,14-6
SENDING UNIT / SENSOR -
INSTALLATION, FUEL LEVEL
.............14-7
SENDING UNIT / SENSOR - OPERATION,
FUEL LEVEL
.....................14-57,14-6
SENDING UNIT / SENSOR - REMOVAL,
FUEL LEVEL
..........................14-7
SENSE - DESCRIPTION, IGNITION
CIRCUIT
............................8E-10
SENSE - OPERATION, IGNITION CIRCUIT
. . 8E-11
SENSE - PCM INPUT - OPERATION, ASD
. . . 8I-5SENSITIVE DEVICES - STANDARD
PROCEDURE, ELECTROSTATIC
DISCHARGE (ESD).................8W-01-8
SENSOR - DESCRIPTION, ACCELERATOR
PEDAL POSITION...............14-22,14-68
SENSOR - DESCRIPTION, AMBIENT
TEMP.............................8M-10
SENSOR - DESCRIPTION, BATTERY
TEMPERATURE......................8F-21
SENSOR - DESCRIPTION, CAMSHAFT
POSITION..........................14-71
SENSOR - DESCRIPTION, CAMSHAFT
POSITION............................8I-7
SENSOR - DESCRIPTION, CRANKSHAFT
POSITION.....................14-23,14-72
SENSOR - DESCRIPTION, ENGINE
COOLANT TEMPERATURE...............7-38
SENSOR - DESCRIPTION, EVAPORATOR
TEMPERATURE......................24-22
SENSOR - DESCRIPTION, FRONT WHEEL
SPEED..............................5-47
SENSOR - DESCRIPTION, FUEL LEVEL
SENDING UNIT..................14-57,14-6
SENSOR - DESCRIPTION, FUEL
PRESSURE.........................14-60
SENSOR - DESCRIPTION, HEATED SEAT . . 8G-11
SENSOR - DESCRIPTION, INLET AIR
TEMPERATURE SENSOR/PRESSURE......14-79
SENSOR - DESCRIPTION, INPUT SPEED . 21-382
SENSOR - DESCRIPTION, INTAKE AIR
TEMPERATURE......................14-30
SENSOR - DESCRIPTION, INTAKE AIR
TEMPERATURE SENSOR/MAP...........14-82
SENSOR - DESCRIPTION, KNOCK........8I-14
SENSOR - DESCRIPTION, LINE
PRESSURE (LP)....................21-382
SENSOR - DESCRIPTION, MAP.....14-32,14-83
SENSOR - DESCRIPTION, MODE . 21-509,21-538,
21-573
SENSOR - DESCRIPTION, OUTPUT
SPEED............................21-391
SENSOR - DESCRIPTION, OXYGEN.......14-35
SENSOR - DESCRIPTION, POSITION....21-442,
21-477
SENSOR - DESCRIPTION, SIDE IMPACT . . 8O-59
SENSOR - DESCRIPTION, SPEED.......21-253
SENSOR - DESCRIPTION, THROTTLE
POSITION..........................14-41
SENSOR - DESCRIPTION,
TRANSMISSION RANGE........21-263,21-405
SENSOR - DESCRIPTION,
TRANSMISSION TEMPERATURE . . 21-267,21-408
SENSOR - DESCRIPTION, WATER IN
FUEL..............................14-66
SENSOR - DIAGNOSIS AND TESTING,
AMBIENT TEMPERATURE..............8M-10
SENSOR - DIAGNOSIS AND TESTING,
HEATED SEAT .......................8G-11
SENSOR - DIAGNOSIS AND TESTING,
REAR WHEEL SPEED..................5-49
SENSOR - INSTALLATION,
ACCELERATOR PEDAL POSITION . . . 14-22,14-71
SENSOR - INSTALLATION, BATTERY
TEMPERATURE......................8F-21
SENSOR - INSTALLATION, CAMSHAFT
POSITION..........................14-72
SENSOR - INSTALLATION, CAMSHAFT
POSITION...........................8I-10
SENSOR - INSTALLATION, CRANKSHAFT
POSITION.....................14-25,14-73
SENSOR - INSTALLATION, ENGINE
COOLANT TEMPERATURE...............7-41
SENSOR - INSTALLATION, EVAPORATOR
TEMPERATURE......................24-22
SENSOR - INSTALLATION, FRONT
WHEEL SPEED........................5-48
SENSOR - INSTALLATION, FUEL LEVEL
SENDING UNIT.......................14-7
SENSOR - INSTALLATION, FUEL
PRESSURE.........................14-61
SENSOR - INSTALLATION, INLET AIR
TEMPERATURE SENSOR/PRESSURE
......14-79
SENSOR - INSTALLATION, INPUT SPEED
. 21-382
SENSOR - INSTALLATION, INTAKE AIR
TEMPERATURE
......................14-31
SENSOR - INSTALLATION, INTAKE AIR
TEMPERATURE SENSOR/MAP
...........14-82
SENSOR - INSTALLATION, KNOCK
........8I-15SENSOR - INSTALLATION, LINE
PRESSURE (LP)....................21-383
SENSOR - INSTALLATION, MAP.........14-34
SENSOR - INSTALLATION, OUTPUT
SPEED............................21-392
SENSOR - INSTALLATION, OXYGEN......14-36
SENSOR - INSTALLATION, POSITION....21-443,
21-478
SENSOR - INSTALLATION, REAR WHEEL
SPEED..............................5-48
SENSOR - INSTALLATION, THROTTLE
POSITION..........................14-43
SENSOR - INSTALLATION,
TRANSMISSION RANGE..............21-266
SENSOR - OPERATION, ACCELERATOR
PEDAL POSITION...............14-22,14-68
SENSOR - OPERATION, AMBIENT TEMP . . 8M-10
SENSOR - OPERATION, BATTERY
TEMPERATURE......................8F-21
SENSOR - OPERATION, CAMSHAFT
POSITION..........................14-71
SENSOR - OPERATION, CAMSHAFT
POSITION............................8I-7
SENSOR - OPERATION, CRANKSHAFT
POSITION.....................14-23,14-72
SENSOR - OPERATION, ENGINE
COOLANT TEMPERATURE...............7-38
SENSOR - OPERATION, EVAPORATOR
TEMPERATURE......................24-22
SENSOR - OPERATION, FRONT WHEEL
SPEED..............................5-47
SENSOR - OPERATION, FUEL LEVEL
SENDING UNIT....................14-57,14-6
SENSOR - OPERATION, FUEL PRESSURE . . 14-60
SENSOR - OPERATION, HEATED SEAT....8G-11
SENSOR - OPERATION, INLET AIR
TEMPERATURE SENSOR/PRESSURE......14-79
SENSOR - OPERATION, INPUT SPEED . . . 21-382
SENSOR - OPERATION, INTAKE AIR
TEMPERATURE......................14-30
SENSOR - OPERATION, INTAKE AIR
TEMPERATURE SENSOR/MAP...........14-82
SENSOR - OPERATION, KNOCK..........8I-14
SENSOR - OPERATION, LINE PRESSURE
(LP)..............................21-383
SENSOR - OPERATION, MAP...........14-32
SENSOR - OPERATION, MODE . . . 21-509,21-539,
21-573
SENSOR - OPERATION, OUTPUT SPEED . . 21-391
SENSOR - OPERATION, POSITION......21-442,
21-477
SENSOR - OPERATION, SIDE IMPACT....8O-59
SENSOR - OPERATION, SPEED.........21-253
SENSOR - OPERATION, THROTTLE
POSITION..........................14-41
SENSOR - OPERATION, TRANSMISSION
RANGE......................21-263,21-405
SENSOR - OPERATION, TRANSMISSION
TEMPERATURE...............21-267,21-408
SENSOR - OPERATION, WATER IN FUEL . . 14-66
SENSOR - REMOVAL, ACCELERATOR
PEDAL POSITION...............14-22,14-68
SENSOR - REMOVAL, BATTERY
TEMPERATURE......................8F-21
SENSOR - REMOVAL, CAMSHAFT
POSITION..........................14-72
SENSOR - REMOVAL, CAMSHAFT
POSITION............................8I-9
SENSOR - REMOVAL, CRANKSHAFT
POSITION.....................14-24,14-73
SENSOR - REMOVAL, ENGINE COOLANT
TEMPERATURE.......................7-39
SENSOR - REMOVAL, EVAPORATOR
TEMPERATURE......................24-22
SENSOR - REMOVAL, FRONT WHEEL
SPEED..............................5-48
SENSOR - REMOVAL, FUEL LEVEL
SENDING UNIT.......................14-7
SENSOR - REMOVAL, FUEL PRESSURE . . . 14-60
SENSOR - REMOVAL, HEATED SEAT.....8G-11
SENSOR - REMOVAL, INLET AIR
TEMPERATURE SENSOR/PRESSURE
......14-79
SENSOR - REMOVAL, INPUT SPEED
.....21-382
SENSOR - REMOVAL, INTAKE AIR
TEMPERATURE
......................14-30
SENSOR - REMOVAL, INTAKE AIR
TEMPERATURE SENSOR/MAP
...........14-82
SENSOR - REMOVAL, KNOCK
...........8I-15
DRINDEX 29
Description Group-Page Description Group-Page Description Group-Page