1998 CHEVROLET PRIZM wheel

Downloaded from www.Manualslib.com manuals search engine Pull out the spare tire. See “Compact Spare Tire”
later in this section for more information about the
compact spare.
Remove the wheel wrench and jack handle from the
foam tray.
The jack is
on the right side
of the trunk. Turn the jack
screw
to remove the jack
from the clamps.
The tools you’ll be using include the jack
(A), jack
handle
(B) and wheel wrench (C).
5-25

Downloaded from www.Manualslib.com manuals search engine c
Attach the jack handle to the jack. Turn the jack handle
to the right to raise the lift head. Remove
the wheel cover, if your vehicle is equipped
with one, by using the flat end
of the wheel wrench. Pry
along the edge of the wheel cover until it comes off. Be
careful; the rim edges may be sharp. Don’t try
to remove
it with your bare hands.
5-26

Downloaded from www.Manualslib.com manuals search engine Removing the Flat Tire and Installing the
Spare Tire
If your wheel has a center cover, insert the flat end of
the wheel wrench into the slot to remove the center cap.
Pry the cap off.
1. Using the wheel wrench, loosen all the wheel nuts.
Don’t remove them yet.
5-27

Downloaded from www.Manualslib.com manuals search engine 3. Raise the vehicle by rotating the jack handle to the
right. Raise
the vehicle far enough off the ground so
there is enough room for the spare tire to fit.
4. Remove all the wheel
nuts and take off the
flat tire.
5. Remove any rust or dirt
from the wheel bolts,
mounting surfaces and
spare wheel.
5-29

Downloaded from www.Manualslib.com manuals search engine A CAUTION:
Rust or dirt on the wheel, or on the parts to
which
it is fastened, can make the wheel nuts
become loose after
a time. The wheel could come
off and cause an accident. When you change a
wheel, remove any rust or dirt from the places
where the wheel attaches to the vehicle. In an
emergency, you can use
a cloth or a paper towel
to do this; but be sure to use a scraper or wire
brush later,
if you need to, to get all the rust or
dirt
off.
Never use oil or grease on studs or nuts. If you
do, the nuts might come loose. Your wheel could
fall
off, causing a serious accident.
6. Replace the wheel nuts
with the rounded end
of
the nuts toward the
wheel. Tighten each
nut
by hand until the wheel
is held against the hub.
5-30

Downloaded from www.Manualslib.com manuals search engine 7. Lower the vehicle by turning the jack handle to the
left. Lower the jack completely.
8. Tighten the wheel nuts
firmly
in a crisscross
sequence
as shown.
Incorrect wheel nuts or improperly tightened
wheel nuts can cause the wheel to become loose
and even come off. This could lead to
an accident.
Be sure to use the correct wheel nuts. If you have
to replace them, be sure to get new
GM original
equipment wheel nuts.
Stop somewhere
as soon as you can and have
the nuts tightened with
a torque wrench to
100 lb-ft (140 N-m).
5-31

Downloaded from www.Manualslib.com manuals search engine A. Spare or Flat Tire
B. Jack Handle
C. Wheel Wrench
D. Jack
Replace the jack, jack handle, wheel wrench and flat or
spare tire.
Storing a Flat or Spare Tire and Tools
Although the compact spare tire was fully inflated
when your vehicle was new, it can lose air after a time.
Check the inflation pressure regularly. It should be 60 psi
(420 kPa).
After installing the compact spare on your vehicle, you should stop as soon as possible and make sure
your spare tire is correctly inflated. The compact spare is made to perform well at speeds up to 65 mph
(105
km/h) for distances up to 3,000 miles (5 000 km),
so you can finish your trip and have your full-size tire
repaired or replaced where you want. Of course, it’s best
to replace your spare with a full-size tire as soon
as you
can. Your spare will last longer and be in good shape in
case you need it again.
5-32

Downloaded from www.Manualslib.com manuals search engine NOTICE:
Improperly tightened wheel nuts can lead to
brake pulsation and
rotor damage. To avoid
expensive brake repairs, evenly tighten the wheel
nuts in the proper sequence and to the proper
torque specification.
Don’t try to put a wheel cover on your compact spare
tire.
It won’t fit. Store the wheel cover in the trunk
until you have the flat tire repaired or replaced.
I NOTICE:
Wheel covers won’t fit on your compact spare.
If you try to put a wheel cover on your compact
spare, you could damage the cover or the spare. Storing
a jack, a tire
or other equipment in the
passenger compartment
of the vehicle could
cause injury. In a sudden stop
or collision, loose
equipment could strike someone. Store all these
in the proper place.
5-33