1998 CHEVROLET CAMARO fuses

Downloaded from www.Manualslib.com manuals search engine Transmitter Verification (If Equipped)
This feature provides feedback to the holder of the
keyless entry transmitter that a command has been
received by the keyless entry receiver. The parking
lamps will flash
on every lock and unlock command and
the horn will sound only if the
LOCK button is pressed
twice within five seconds. This allows for silent
operation
of locking and unlocking, unless a confirming
horn chirp is desired. Other options may be selected for
this feature (see “Feature Customization” in the Index).
Matching Transmitter(s) To Your Vehicle
Each keyless entry transmitter is coded to prevent another
transmitter from unlocking your vehicle.
If a transmitter
is lost or stolen, a replacement can be purchased through
your dealer. Remember to bring any remaining
transmitters with you when you go
to your dealer. When
the dealer matches the replacement transmitter to your
vehicle, any remaining transmitters must also be matched.
Once your dealer has coded the new transmitter, the lost transmitter will not unlock your vehicle. Each vehicle can
have only four transmitters matched to
it.
Have each transmitter you intend to match ready for the
next steps.
To match transmitters to your vehicle:
1. Turn the ignition to RUN, then to OFF. This
will disarm the Vehicle and Content Theft-DeterrenVAlann System (if your vehicle
has
this option).
2. Remove the RADIO fuse. This fuse is located in the
main fuse block which is located on the left side
of
your main instrument panel. When the fuse block is
open the radio fuse is located on the lower right hand
corner of your instrument panel. See “Fuses and
Circuit Breakers’’ in the Index.
3. Turn the ignition from OFF to RUN three times
quickly (within five seconds). The vehicle will
respond by locking the doors, unlocking the driver’s
doors and releasing the hatch. Your transmitter is
now ready to match the vehicle.
4. Press and hold the LOCK and UNLOCK buttons on
the first transmitter for
15 seconds. The vehicle will
respond as in Step
3.
5. Repeat Step 4 for the remaining transmitters.
6. When you have finished matching all of your
7. Check that all transmitters work by pressing
If the transmitters don’t work, or if you’d rather not
match the transmitters yourself,
see your dealer.
transmitters, replace the
RADIO fuse.
their buttons.
2-10

Downloaded from www.Manualslib.com manuals search engine PASS-Key@ I1
1
Your vehicle is equipped
with the PASS-Key I1
(Personalized Automotive
Security System)
theft-deterrent system.
PASS-Key
I1 is a passive
theft-deterrent system.
It works when you insert
or remove the key from
the ignition.
PASS-Key
I1 uses a resistor pellet in the ignition key
that matches a decoder in your vehicle.
When the PASS-Key
I1 system senses that someone is
using the wrong key, it shuts down the vehicle’s starter
and fuel systems. For about three minutes, the starter
won’t work and fuel won’t go to the engine. If someone
tries to start your vehicle again or uses another key
during this time, the vehicle will not start. This
discourages someone from randomly trying different
keys with different resistor pellets in an attempt
to
make a match. The ignition key must
be clean and dry before it’s
inserted in the ignition or the engine may not start. If
the engine does not start and the
SECURITY light stays
on when you
try to start the vehicle, the key may be
dirty or wet.
Turn the ignition off.
Clean and dry the key. Wait about three minutes and
try
again. The SECURITY light may remain on during this
time. If the starter still won’t work, and the key appears
to be clean and dry, wait about three minutes and try
another ignition key. At this time, you may also want
to
check the fuses (see “Fuses and Circuit Breakers” in the
Index).
If the starter won’t work with the other key, your
vehicle needs service. If your vehicle does start, the first
ignition key may be faulty. See your dealer or a
locksmith who can service the PASS-Key
11.
If you accidentally use a key that has a damaged or
missing resistor pellet, the starter won’t work. The
SECURITY light will flash. But you don’t have to wait
three minutes before trying another ignition key.
See your dealer or a locksmith who can service the
PASS-Key
I1 to have a new key made.
2-18

Downloaded from www.Manualslib.com manuals search engine ‘To program features, your vehicle must be in the
programming mode. Follow these steps:
1.
2.
3.
4.
5.
Put your key in the ignition.
Turn the ignition to RUN to disarm the Vehicle
and Content Theft-DeterrentIAlarm System.
Turn
the ignition to OFF position.
Remove the RADIO
fuse. This fuse is in the
main fuse block, located on the left side
of your
instrument panel. When the main fuse block is
open, the RADIO fuse
is located in the lower
right corner side
of the fuse panel. See “Fuses and
Circuit Breakers” in the Index.
Turn the ignition to ACC.
You should hear a chime
to verify that the system
is in programming mode.
If the chime sounds once,
you will be able to program Exit Lighting, Delayed
Illumination, Last Door Closed Locking and Lockout
Prevention only. If the chime sounds twice and your
vehicle is equipped with the Vehicle and Content
Theft-Deterrent System, you will also be able to
set Keyless Entry Verification, Arming Method,
Arming Verification, Driver’s Door Delay and
Shock Sensor Enable.
Exit Lighting and Delayed Illumination
With Exit Lighting, your interior lamps will come on
for up to
25 seconds when the key is removed from
the ignition.
With Delayed Illumination, your interior lamps will come
on and stay
on for up to 25 seconds when entering the
vehicle and up
to 5 seconds when leaving your vehicle.
Your vehicle comes with both features enabled (Mode
4).
To change the factory setting, do the following:
1. Turn the courtesy lamps on by turning the instrument
panel brightness control knob all the way up.
2. Count the number of chimes you hear. The number of
chimes tells you which mode your vehicle is set for.
3. Turn the courtesy lamp switch to off.
4. Turn the courtesy lamp switch from on to off until
you hear the number
of chimes that corresponds to
the mode selection you want.
Mode 1: Both Off
Mode 2: Delayed Illumination Only
Mode 3: Exit Lighting Only
Mode 4: Both On
2-20

Downloaded from www.Manualslib.com manuals search engine As you signal a turn or a lane change, if the arrows don’t
flash but just stay on
as you signal a turn or lane change,
a signal bulb may be burned out and other drivers won’t
see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident.
If the arrows don’t go on at all when you
signal a turn, check the fuse (see “Fuses and Circuit
Breakers” in the Index).
Headlamp High/Low-Beam Changer
To change the headlamps
from low beam to high
or
high to low, pull the turn
signal lever all the way
toward you. Then release it.
When the high-beams headlamps
are on, this light on
the instrument panel also will be on.
Windshield Wipers
I 1
I I
i
You can control the windshield wipers by turning the
band with the wiper symbol on it.
For
a single wiping cycle, turn the band to MIST. Hold
it there until the wipers start, then let go. The wipers will
stop after one cycle. If you want more cycles, hold the
band on MIST longer.
You can set the wiper speed for
a long or short delay
between wipes. This can be very useful in light rain or
snow. Turn the band to choose the delay time. The
closer to
LO, the shorter the delay.
2-46

Downloaded from www.Manualslib.com manuals search engine Headlamps
The headlamp wiring is protected by a circuit breaker.
An electrical overload will cause the lamps to go on
and off, or in some cases to remain
off. If this happens,
have your headlamp wiring checked right away.
Windshield Wipers
The windshield wiper motor is protected by a circuit
breaker and a
fuse. If the motor overheats due to heavy
snow, etc., the wiper will stop until the motor cools. If
the overload is caused by some electrical problem and
not snow, etc., be sure to get it fixed.
Power Windows and Other Power Options
Circuit breakers protect the power windows and other
power accessories. When the current load is too heavy,
the circuit breaker opens and closes, protecting the
circuit until the problem
is fixed or goes away.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected
from short circuits by a combination of fuses, circuit
breakers, and fusible thermal links in the wiring itself.
This greatly reduces the chance of fires caused by
electrical problems.
Look at the silver-colored band inside the
fuse. If the
band is broken or melted, replace the fuse. Be sure
you
replace a bad fuse with a new one of the correct size.
If you ever have a problem on
the road and don’t have a
spare fuse, you can borrow one of the correct value. Just
pick some feature of your vehicle that you can get along
without
-- like the radio or cigarette lighter -- and use
its fuse,
if it is the size you need. Replace it as soon as
you can.
6-63

Downloaded from www.Manualslib.com manuals search engine Underhood Electrical Center Fuses
ABS BAT SOL TCS BAT COOL FAN
000
PCM BAT FUEL PUMP AIR PUMP
LH HOW OR RH HDLP DR HORN
r
FAN $43 1L
1
15305529 A
The two underhood fuse and relay centers are located
in the engine compartment. Open the cover to expose
the fuses.
Fuse
ABS BAT SOL
TCS BAT
COOL FAN
PCM BAT
FUEL PUMP
AIR PUMP
--- 1
-
Fuse and Relay Center 1
Usage
Anti-Lock Brake System
Traction Control System
Cooling Fan Control
Powertrain Control Module
Fuel Pump
Air Pump Relay and Bleed Valve
6-66

Downloaded from www.Manualslib.com manuals search engine Battery ...................................... 6-37
Jump Starting
................................. 5-3
Replacement. Keyless Entry .................... 2- 11
Warnings
........................... 5.3.5.4. 6.37
BBB Auto Line
................................. 8-9
Before Leaving on a Long Trip
.................... 4-21
Better Business Bureau Mediation
................... 8-9
Blizzard
...................................... 4-27
Brake Adjustment
.................................. 6-36
Checking Fluid
............................... 6-34
Fluid
....................................... 6-33
Master Cylinder
.............................. 6-33
Parking
..................................... 2-37
Pedal Travel
................................. 6-36
Replacing System Parts
........................ 6-36
System Warning Light
......................... 2-77
Trailer
...................................... 4-34
Transmission Shift Interlock
.................... 2-43
Wear
....................................... 6-35
Brakes. Anti-Lock
............................... 4-7
Braking
........................................ 4-6
Braking
in Emergencies .......................... 4- 10
Break-In. New Vehicle
.......................... 2-24
Brightness Control
.............................. 2-52
BTSICheck
................................... 7-34
Bulb Replacement
.............................. 6-37
BTSI
......................................... 2-43 Canadian
Roadside Assistance
.................... 8-7
Capacities and Specifications
...................... 6-69
Carbon Monoxide
.......... 2.12.2.41.2.42.4.28. 4.33
Cassette Deck Service
........................... 7-32
Cassette Storage
................................ 2-56
Cassette Tape Player
......................... 3.7. 3.9
Care
of
Your Cassette Tape Player .................. 3-24
Cassette Tape Player Care
........................ 3-24
CD Player Theft-Deterrent Feature
................. 3-21
Center High-Mounted Stoplamp Bulb Replacement
.... 6-39
Certification Label
.............................. 4-29
Chains. Safety
................................. 4-34
Chains. Tire
................................... 6-51
Changing a Flat Tire
............................. 5-27
Check Gages Light
.............................. 2-85
Checking Your Restraint Systems
.................. 1-46
Chemical Paint Spotting
.......................... 6-60
Child Restraints
................................ 1-33
Securing
in a Rear Seat Position ................. 1-39
Securing in the Right Front Seat Position
.......... 1-41
WheretoPut
................................ 1-37
Cigarette Lighter
............................... 2-57
Circuit Breakers and Fuses
....................... 6-63
Cleaner. Air
................................... 6-18
Cleaning
Aluminurnwheels
............................ 6-58
Convertible Top
.............................. 6-58
Fabric
...................................... 6-53
TopStrap
................................... 1-38
9-2

Downloaded from www.Manualslib.com manuals search engine Fabric Cleaning ............................... 6-53
Fabric Protection
............................... 6-54
Fancontrol
.................................... 3-2
Feature Customization
........................... 2- 19
Driver’s Door Alarm Delay/Shock Sensor Enable
... 2-23
Exit Lightingmelayed Illumination
............... 2-20
Keyless Entry Verification
...................... 2-21
Last Door Closed LockingLockout Prevention
..... 2-21
Theft-Deterrent Arming Method
................. 2-22
Theft-Deterrent Arming Verification
.............. 2-23
Fifth Gear. Manual Transmission
.............. 2.34. 2.35
Filling a Portable Fuel Container
.................... 6-8
Filter. Air
..................................... 6- 19
Filter. Engine Oil
............................... 6- 17
Finish Care .................................... 6-57
Finish Damage
................................. 6-59
First Gear. Automatic Transmission
................ 2-33
First Gear. Manual Transmission
.............. 2.34. 2.35
Fixed Antenna Mast Care
........................ 3-25
Flashers. Hazard Warning
......................... 5-2
Flat Tire. Changing ............................. 5-27
Floor Mats
.................................... 2-59
Fluids and Lubricants
............................ 7-37
FogLamps
.................................... 2-51
Folding Rear Seatback
............................ 1-6
Foreign Countries. Fuel ........................... 6-5
Fourth Gear. Manual Transmission
............ 2.34. 2.35
Four-Way Manual Seat
........................... 1-3
FillingYourTank
................................ 6-6
French
LanguageManual
11
FrontConsole .................................. 2-56
FrontTowing
................................... 5-9
Front Turn Signal Bulb Replacement
................ 6-39
Fuel
.......................................... 6-3
Filling Your Tank
.............................. 6-6
Gage
....................................... 2-85
In Foreign Countries
........................... 6-5
Fuses and Circuit Breakers ....................... 6-63
.. ...........................
Gages Engine Coolant Temperature
.................... 2-80
Engine Oil Pressure ........................... 2-83
Fuel
....................................... 2-85
GAWR ....................................... 4-29
Gear Positions. Automatic Transmission
............. 2-30
Gear Positions. Manual Transmission
.......... 2-34. 2-35
GloveBox
.................................... 2-55
Gross Axle Weight Rating
........................ 4-29
Gross Vehicle Weight Rating
...................... 4-29
Guide en FranGais 11
GVWR ....................................... 4-29
.. .................................
Halogen Bulbs ................................ 6-37
Hatch
........................................ 2-12
Hatch Release
.................................. 2-12
Hatch Release. Remote
.......................... 2-13
Hazard Warning Flashers .......................... 5-2
9-5