1998 AUDI A6 engine

24-2


1 -
Heated Oxygen Sensor (HO2S) -G39- with
Oxygen Sensor (O2S) heater -Z19-
2 -
Engine Coolant Temperature (ECT) sensor
-G62-
4-pin connector
3 -
Harness connector for: Heated Oxygen Sensor (HO2S) -G39- and
Oxygen Sensor (O2S) heater -Z19- (4-pin,
brown) Oxygen Sensor (O2S) behind Three Way
Catalytic Converter (TWC) -G130- with
Oxygen Sensor (O2S) heater -Z29- (4-pin,
black) Engine speed (RPM) sensor -G28- (3-pin,
gray) Knock sensor (KS) 1 -G61 (3-pin, green)Knock sensor (KS) 2 -G66- (3-pin, blue)
4 -
Electronics box (E-box) with: Motronic Engine Control Module (ECM) -
J220- Barometric Pressure (BARO) sensor -F96-
Pa
ge 2 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

24-4


11 -
Camshaft Position (CMP) sensor -G40-
12 -
Knock Sensor (KS) 1 -G61-
13 -
Knock Sensor (KS) 2 -G66-
14 -
Engine speed (RPM) sensor -G28-
(behind oil filter housing on engine cylinder
block)
15 -
Intake Air Temperature (IAT) sensor -G42-
16 -
Throttle valve control module -J338-
Including:
Throttle drive -G186-Angle sensor 1 for throttle drive -G187-Throttle Position (TP) sensor -G69-Closed Throttle Position (CTP) switch -
F60-
Pa
ge 4 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

24-5

Safety precautions


WARNING!

Fire hazard! Do not smoke, work near heaters
or open flame, or have anything nearby that
could ignite fuel. The fuel system is under
pressure. Before opening, cover connections
with a rag, and open carefully to release
pressure. Be alert when working on or near
the engine and ignition wires. High secondary
ignition voltage can cause serious personal
injury and damage vehicle components.

DO NOT touch or disconnect ignition system
wires when the engine is running or being
cranked at starting RPM.
DO NOT operate starter if fuel injectors are
removed.

Be sure the ignition is switched OFF, when:
Disconnecting or connecting the battery,
ignition wires, or test equipment leads
Disconnecting fuel injection system wiring
Washing the engine or engine
compartment.
Pa
ge 5 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

BEFORE cranking engine at starting RPM
(e.g. for compression testing) disable ignition
and fuel injection systems:

Disconnect both ignition coil power output
stages, and both Motronic fuses at the E-box
in the plenum.
Disconnect harness connectors from all fuel
injectors.
Afterward, erase DTC memory.
Pa
ge 6 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

24-6

CAUTION!

BEFORE disconnecting the battery:

Stop the engine.
Be sure the ignition is switched OFF (also
applies when connecting the battery). Failure
to do so may damage the Engine Control
Module (ECM).
Be sure of the proper radio code (for vehicles
equipped with coded anti-theft radio).

Be sure the battery negative (-) cable is
disconnected, when:
Working on the electrical system
Resistance (spot) welding or electric arc
welding anywhere on the vehicle.

When connecting and disconnecting
electrical test equipment (LED voltage tester,
multimeter, etc.):
Be sure the ignition is switched OFF.
Use correct adapters from the VW 1594
Pa
ge 7 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

connector test kit.

For any work affecting the Engine Control
Module (ECM):
BEFORE disconnecting the ECM harness
connector, switch the ignition OFF and WAIT
at least 20 seconds. Failure to do so may
damage the ECM.
DO NOT connect any outside voltage source
to stimulate an output signal at the ECM.
Pa
ge 8 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

24-8
Technical data

Engine code
AEB

Engine idle speed:
not adjustable, maintained by Idle Air Control (IAC) 820-900 RPM
Engine speed (RPM) upper limit:
actuated by switching off fuel injectors approx. 6500 RPM
Fuel system pressure at idle Vacuum hose for pressure regulator connected: approx. 3.5 bar
(50 psi)

Vacuum hose for pressure regulator disconnected: approx. 4.0 bar
(58 psi)

Residual fuel pressure after 10 minutes at least 2.5 bar
Fuel injectors Spray pattern: approx. the same for all fuel injectors

Resistance
1)
:
11-13 ohm
1) Engine at room temperature; with the engine at normal operating temperature the resistance increases by approx. 4-6
ohms.
Pa
ge 11 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

24-9

Fuel injection system, servicing

Servicing ignition system:

Repair Group 28

Notes:

Fuel hoses in the engine compartment must be
secured with spring-type clamps. Screw-type
clamps or equivalent must not be used.
The Engine Control Module (ECM) has On
Board Diagnostic (OBD) capability, and is
equipped with Diagnostic Trouble Code (DTC)
memory. Before repairing or adjusting any
components or systems, first check DTC
memory. Also check all vacuum connections for
leaks ("false air").
For proper operation of electrical and electronic
components, a Battery Positive Voltage (B+)
supply of at least 11.5 volts is required.
Do not use any gasket sealers or other
automotive chemical compounds that contain
silicone. Traces of silicone drawn into the
engine pass unburned into the exhaust and can
damage the oxygen sensors.
Pa
ge 12 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1