1998 AUDI A4 buttons

24-102
Significance of 3 digit indication of display group 030 X
X
X
Display fields 1 to 4
X Oxygen sensor control
0= not active
1 = active
X Operational readiness of oxygen sensor
0= not active
1 = active
X Condition of oxygen sensor heating
0= not active
1 = active

- Press -C- button.Basic Setting
Q
Input displa
y group number XXX

When indicated on display:
- Press buttons -0-, -4- and -3- to select "display group number 043" and press -Q-
button to confirm input.
System in Basic Setting 43
1
2
3
4

When indicated on display:
- Check specified value in display field 4 after indication "Test ON" appears:
Pa
ge 32 of 63 Ox
yg
en sensor control, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.3

24-103


Display fields

1 2 3 4
Display group 043: Oxygen sensor aging, oxygen sensor behind catalytic converter (bank 1)
Display xxxx/min
xxx C
x.xxx V
---
Indicated Engine speed
(RPM) Exhaust
temperature Voltage of oxygen sensor
behind catalytic converter,
bank 1 Diagnostic condition
Functional
range 630 to 6800
RPM 70 to 850 C
0.100 to 1.000 volts Test OFF
Test ON
B1-S2 OK
B1-S2 not OK
Specified
value 1800 to 2400
RPM above 380 C 0.100 to 1.000 volts B1-S2 OK
Notes



If specified value is not obtained
Check oxygen sensor heater Page
24
-116

If specified value B1-S2 OK" is obtained:

- Press -C- button.

- Press buttons -0-, -4- and -4- to select "display
group number 044" and press -Q- button to
confirm input.
Pa
ge 33 of 63 Ox
yg
en sensor control, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.3

24-105

Checking oxygen sensor control behind
catalytic converter

- Perform a test drive of approx. 10 minutes.

WARNING!

Observe safety precautions to reduce the risk
of accidents during road test Page 24
-1 .

- Let engine continue to run at idle.Basic Setting
Q
Input displa
y group number XXX

When indicated on display:
- Press buttons -0-, -3- and -7- to select "display group number 037" and
press -Q- button to confirm input.
System in Basic Setting 37
1
2
3
4

When indicated on display:
- Check oxygen sensor voltage in display field 2.
- Check dwell time between oxygen sensor 1 before catalytic converter
and oxygen sensor 2 behind catalytic converter in display field 3 and
diagnostic result in display field 4.
Pa
ge 36 of 63 Ox
yg
en sensor control, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.3

24-107

- Press -C- button.

- Press buttons -0-, -3- and -8- to select "display
group number 038" and press -Q- button to
confirm input. System in Basic Setting 38
1
2
3
4

When indicated on display:
Note:
The test in display group 038 is activated simultaneously with the test in
display group 037 Therefore the test result is indicated immediately after
display group 038 is selected. - Check specified value in display field 4.
Pa
ge 39 of 63 Ox
yg
en sensor control, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.3

24-117

Note:
The heating circuit of the oxygen sensor is
monitored by On Board Diagnostic (OBD),
Check DTC memory Page 01
-15
.

- Connect VAS5051 tester or VAG1551 scan tool
and select the control module for engine
electronics using "address word" 01 Page 01
-
9 .

Engine must run at idle for this.Rapid data transfer
HELP
Select function XX

When indicated on display:
- Press buttons -0- and -8- to select "Read Measuring Value Block" and
press -Q- button to confirm input.
Read Measurin
g Value Block
Q
Input displa
y group number XXX

When indicated on display:
- Press buttons -0-, -4- and -1- to select "display group number 041" and
press -Q- button to confirm input.
Read Measuring Value Block 41
1
2
3
4

When indicated on display:
Note:
Increasing engine speed accelerates the obtaining of specified values. - Check specified values in display fields 1 and 3.
Pa
ge 50 of 63 Ox
yg
en sensor control, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.3

Read Measurin
g Value Block
Q
Input display group number XXX

When indicated on display:
- Press buttons -0-, -4- and -2- to select "display group number 042" and press -Q-
button to confirm input.
Pa
ge 52 of 63 Ox
yg
en sensor control, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.3