1998 AUDI A4 display

System in Basic Setting 47
1
2
3
4

Indicated on display (1-4 display fields)
Pa
ge 19 of 29 Readiness code11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.2

01-85

- Hold engine speed at 1800-2200 RPM until
display changes from "Test OFF" to "Test ON" in
display field 4.

- Continue to hold at 1800-2200 RPM until
specified value "Cat B2 OK" is indicated in
display field 4.

Note:
The test time for TWC diagnosis is approx. 60
seconds.

Display fields

1 2 3 4
Display group 47: Three Way Catalytic Converter (TWC), Bank 2 diagnosis
Display x.xx x xx.x s Test OFF/Test ON
Cat B2 OK/
Cat B2 n. OK
Indicated Amplitude ratio Exceeded diagnosis range Test time of TWC diagnosis Diagnostic status
Diagnostic result
Range 0.00-1.00 0-9 00.0-60.0 ---
Specified value 0.00-0.26 0-2 60.0 s Cat B2 OK
Pa
ge 20 of 29 Readiness code11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.2

If "Cat B2 n. OK" is indicated in display field 4:

- Check DTC memory page 01
-16
.
If specified value "Cat B2 OK" is indicated in
display field 4:

- Press -C- button.
Pa
ge 21 of 29 Readiness code11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.2

01-86

Step 8: Evaporative Emissions (EVAP)
system and fuel tank leak detection

Note:
During this diagnosis there should be no engine
load, otherwise the diagnosis is interrupted and
can only be restarted after pressing the
accelerator pedal momentarily.

- Start engine and let run at idle.Basic Settin
g
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -7- and -0- to input display group number 70 (070),
and press -Q- button to confirm input.
System in Basic Setting 70
1
2
3
4

Indicated on display (1-4 display fields)
If the diagnosis is initiated by the ECM, the display changes from "Test
OFF" to "Test ON" in display field 4.
Note:
If the display changes from "Test ON" to "Test OFF" during the diagnosis,
briefly accelerate the engine to reset and repeat the test. - Let engine continue to run at idle until the specified value "EVAP OK" is
indicated in display field 4.
Pa
ge 22 of 29 Readiness code11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.2

01-87


Display fields

1 2 3 4
Display group 70: Evaporative Emissions (EVAP) canister purge regulator valve diagnosis
Display xxx % xx.x % xx.xx g/s Test
OFF/Test ON
EVAP OK/
EVAP n. OK
Indicated Opening of EVAP canister purge
regulator valve during diagnosis Oxygen sensor control
deviation during diagnosis Idle Air Control (IAC) valve
deviation during diagnosis Diagnostic
status
Diagnostic
result
Range 0 - 100 % -25.0 to +25.0 % -2.78 to +2.85 g/s ---
Specified
value 0 - 93 % -15.0 to +15.0 % -1.00 to 0.00 g/s EVAP OK If "EVAP n. OK" is indicated in display field 4:

- Check DTC memory page 01
-16
.
If the specified value "EVAP OK" is indicated in
display field 4:

- Press -3- button to input display group number
71.
Pa
ge 23 of 29 Readiness code11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.2

01-88

Initiate basic setting 71
1
2
3
4

Indicated on display (1-4 display fields)
If the diagnosis is initiated by the ECM, the display changes from "Test
OFF" to "Test ON" in display field 4. - Start engine and let run at idle.
- Let engine continue to run at idle until the specified value "Syst. OK" is
indicated in display field 4.

Display fields

1 2 3 4
Display group 71: Fuel tank leak detection
Display Reed op.
Reed cl. Small leak/large leak
disconnection Syst.Test
Check
Check end Test OFF/Test ON
Syst. OK/
Syst. n.OK
Indicated Status: Reed contact Error message System status Diagnostic status
Diagnostic result
Range --- --- --- ---
Specified value Reed op. --- Check end Syst. OK
Pa
ge 24 of 29 Readiness code11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.2

01-89

Notes:
If display field 4 changes from "Test ON" to "Test
OFF" and "Abort" appears in display field 2,
repeat the diagnosis of fuel tank leak detection.
Shut the engine off, start the engine again and
repeat the leak detection test.
Diagnosis conditions for fuel tank leak detection:

Intake Air Temperature (IAT) must be less than
60 C (140 F) display group 4, display field 4
(the temperature can be reduced by opening
the hood).

The throttle valve angle for vehicles with
automatic transmissions must be smaller than
10 display group 3, display field 3

The throttle valve angle for vehicles with
manual transmissions must be smaller than
10 display group 3, display field 3
If "Syst. n. OK" is indicated in display field 4:

- Check DTC memory page 01
-16
.
If the specified value "Syst. OK" is indicated in
display field 4:
Pa
ge 25 of 29 Readiness code11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.2

01-90

Step 9: Secondary Air Injection (AIR) system
diagnosis

- Start engine and let run at idle.Initiate basic setting
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -7- and -7- to input display group number 77 (077),
and press -Q- button to confirm input.
System in Basic Setting 77
1
2
3
4

Indicated on display (1-4 display fields)
If the diagnosis is initiated by the ECM, the display changes from "Test
OFF" to "Test ON" in display field 4. - Let engine continue to run at idle until the specified value "Syst. OK" is
indicated in display field 4.
Pa
ge 27 of 29 Readiness code11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.2