Page 103 of 369
Downloaded from www.Manualslib.com manuals search engine 42-7
     Protruding segment of bonded rubber mounting faces 
forward on inside and rearward on outside.  Fig. 7 Rubber bonded mounting, installation 
position     Press both halves in one after the other until the 
mounting conical section contacts the axle beam.  Fig. 8 Rubber bonded mounting, presssing 
into axle beam Page 7 of 14Rear Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.1  
         
        
        
     
        
        Page 104 of 369
Downloaded from www.Manualslib.com manuals search engine 42-8
     
Reworking cap nut in side member 
(front wheel drive vehicles)  
    If the threads of the cap nut in the side member 
are damaged, it must either be retapped or the 
cap nut must be drilled out. When drilling out 
proceed as follows:  
    
- Remove rear axle.     
- Drill through damaged cap nut in the side 
member using a 10.2 mm diameter drill from 
underneath. 
    
Note:  
    Do not tilt the drill when drilling. 
    
WARNING! 
    
Wear protective goggles. 
    
- Cut new thread in the cap nut, M 12 x 1.5.     
- Use new bolts, Part No. N 010.127.4 (M 12 x 1.5 x 30), and washer, Part No. N 011.531.7, to 
secure the rear axle. 
    Tightening torque: 70 Nm (52 ft lb)  
    
Note:  
    The procedure described here must only be 
performed on one cap nut on each side of the 
vehicle. Page 8 of 14Rear Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.1  
         
        
        
     
        
        Page 105 of 369
Downloaded from www.Manualslib.com manuals search engine 42-9
   
Suspension strut, 
disassembling and 
assembling (front wheel 
drive vehicles)  
1 - Cap  Pry out with 
screwdriver  Pressing on  Fig. 4 2 - O-ring 
3 - Self-locking hex nut, 25 Nm (18 ft lb) 
4 - Dished washer 
5 - Upper rubber mounting 6 - Gasket (foam)  Always replace Page 9 of 14Rear Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.1  
         
        
        
     
        
        Page 106 of 369
Downloaded from www.Manualslib.com manuals search engine 42-10
   
7 - Suspension strut 
bearing  Always replace foam 
gasket  Welded nuts must be 
located in the spring 
seat recesses  Align welded nuts and 
cap to shock absorber 
lower bushing  Fig. 3 8 - Spacer tube 
9 - Lower rubber 
mounting 
10 - Metal cap  Higher on Wagon than 
Sedan 
11 - Washer 
12 - Spring seat  Thinner on Wagon 
than Sedan  Installation position  
Fig. 2 Page 10 of 14Rear Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.1  
         
        
        
     
        
        Page 107 of 369
Downloaded from www.Manualslib.com manuals search engine 42-11
   
13 - Stop buffer  Shorter on Wagon 
than Sedan 
14 - Protective tube  Longer on Wagon than Sedan 
15 - Plastic cap 
16 - Coil spring  Removing and 
installing  Fig. 1  Allocation  Parts 
catalog  Wagon has protective 
hose at top 
17 - Packing 
18 - Circlip 
19 - Lower spring plate Page 11 of 14Rear Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.1  
         
        
        
     
        
        Page 108 of 369
Downloaded from www.Manualslib.com manuals search engine 42-12
   
20 - Shock absorber  Can be replaced 
individually  Removing and 
installing  Page 42-4  Application see Parts 
catalog Page 12 of 14Rear Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.1  
         
        
        
     
        
        Page 109 of 369
Downloaded from www.Manualslib.com manuals search engine 42-13
     Note:  
Instead of VAG 1403, VAG 1752/1 may be used.  Fig. 1 Spring, removing and installing     Fig. 2 Spring seat, installation position Page 13 of 14Rear Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.1  
         
        
        
     
        
        Page 110 of 369
Downloaded from www.Manualslib.com manuals search engine 42-14
     Fig. 3 Suspension strut mounting to shock 
absorber bushing, aligning 
A - Shock absorber bushing axis B - Suspension strut mounting axis   "a" 50 C - Cap axis 90 offset to shock absorber bushing 
axis -A-.     Fig. 4 Cap in suspension strut mounting, 
pressing in. Page 14 of 14Rear Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.1