SR140-01
R11204
R11203
Screwdriver
Key Cylinder
R01835
SR-16
- STEERINGTILT STEERING COLUMN
1900 Author: Date:
1997 SUPRA (RM502U)
INSPECTION
1. INSPECT COLUMN UPPER BRACKET
Check that the steering lock mechanism operates properly.
2. IF NECESSARY, REPLACE KEY CYLINDER
(a) Place the ignition key at the ACC position.
(b) Push down the stop pin with a screwdriver and pull out the
key cylinder.
(c) Install a new key cylinder.
HINT:
Make sure the ignition key is at the ACC position.
3. INSPECT IGNITION SWITCH
(See page BE-13)
4. IF NECESSARY, REPLACE IGNITION SWITCH
(a) Remove the 2 screws.
(b) Install new switch with the 2 screws.
5. INSPECT KEY UNLOCK WARNING SWITCH
(See page BE-13)
6. A/T:
INSPECT KEY INTERLOCK SOLENOID
(See page AT-17, AT-15)
7. IF NECESSARY, REPLACE KEY UNLOCK WARNING
SWITCH
(a) Remove the 2 screws.
(b) Install a new switch with the 2 screws.
8. A/T:
IF NECESSARY, REPLACE KEY INTERLOCK SOLE-
NOID WITH KEY UNLOCK WARNING SWITCH
(a) Remove the 4 screws.
(b) Install a new solenoid and warning switch with the 4
screws.
9. IF NECESSARY, REPLACE BUSHING
(a) Using a screwdriver, depress the 3 projections on the bus-
ing and remove the bushing from the column lower tube.
(b) Align the projections on a new bushing with the holes in
the lower tube. Install the bushing until the projections are
firmly engaged in the holes in the lower tube.
R07557
SR-20
- STEERINGTILT STEERING COLUMN
1904 Author: Date:
1997 SUPRA (RM502U)
(b) Install a new E-ring.
14. INSTALL TURN SIGNAL BRACKET
(a) Apply sealant to 2 or 3 threads of the 2 bolts.
Sealant:
Part No. 08833-00080, THREE BOND 1344,
LOCTITE 242 or equivalent.
(b) Torque the 2 bolts.
Torque: 8.8 N´m (90 kgf´cm, 78 in.´lbf)
15. INSTALL STEERING DAMPER
Torque the 2 bolts.
16. INSTALL 3 TENSION SPRINGS
17. INSTALL COMPRESSION SPRING
(a) Install the 2 bushings to the spring.
(b) Apply sealant to 2 or 3 threads of the torx screw.
Sealant:
Part No. 08833-00080, THREE BOND 1344,
LOCTITE 242 or equivalent.
(c) Using a torx socket wrench, torque the screw.
Torque: 6.4 N´m (65 kgf´cm, 56 in.´lbf)
18. INSTALL COLUMN PROTECTOR AND WIRING HAR-
NESS CLAMP
Tighten the 2 screws.
19. INSTALL COLUMN UPPER BRACKET AND COLUMN
UPPER CLAMP
Tighten 2 new tapered-head bolts until the bolt head breaks off.
20. INSTALL COLUMN LOWER COVER
Tighten the clamp.
21. INSTALL SHAFT THRUST STOPPER AND SLIDING
YOKE
(a) Align the matchmarks on the yoke and main shaft.
(b) Torque the bolt.
Torque: 35 N´m (360 kgf´cm, 26 ft´lbf)
22. INSTALL INTERMEDIATE SHAFT
Temporarily tighten the bolt.
23. INSTALL IGNITION KEY CYLINDER ILLUMINATION
24. CHECK TILT OPERATION
