1997 TOYOTA SUPRA brake sensor

SA0OZ-02
F08323
Suspension Support
Spring Support
Reinforcement
Washer TankInsulator
Coil Spring
Brake Caliper
Front Fender Splash Shield
Non-reusable part Stabilizer BarCotter PIn Bushing
Front
Shock
Absorber Upper
Suspension
Arm Plug

ABS Speed SensorFront Shock Absorber
Assembly
- SUSPENSION AND AXLEFRONT SHOCK ABSORBER
SA-19
1709 Author
: Date
:
1997 SUPRA (RM502U)
FRONT SHOCK ABSORBER
COMPONENTS

SA0P0-01
SA3578
R00159
SA-20
- SUSPENSION AND AXLEFRONT SHOCK ABSORBER
1710 Author
: Date
:
1997 SUPRA (RM502U)
REMOVAL
1. REMOVE FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE BRAKE CALIPER
(a) Remove the 2 bolts and brake caliper from the steering
knuckle.
Torque: 118 N´m (1,200 kgf´cm, 87 ft´lbf)
(b) Support the brake caliper securely.
3. DISCONNECT ABS SPEED SENSOR AND WIRE HAR-
NESS
(a) Remove the bolt and disconnect the speed sensor from
the steering knuckle.
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
(b) Remove the 3 bolts and disconnect the wire harness
clamp to prevent the wire harness from being damaged
when removing or installing the through bolt of the upper
suspension arm.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
4. REMOVE FRONT FENDER SPLASH SHIELD
5. LH side only:
MOVE WASHER TANK
(a) Remove the 2 washer tank set bolts.
(b) Move the washer tank away from the body.
6. DISCONNECT UPPER SUSPENSION ARM
(a) Remove the bolt and nut and disconnect the upper sus-
pension arm from the sub-frame.
Torque: 164 N´m (1,670 kgf´cm, 121 ft´lbf)
HINT:
At the time of installation, after stabilizing the suspension,
torque the nut.
(b) Support the upper suspension arm securely.
7. DISCONNECT STABILIZER BAR LINK
Remove the nut and disconnect the stabilizer bar link.
Torque: 74 N´m (750 kgf´cm, 54 ft´lbf)
HINT:
If the ball joint stud turns together with the nut, use a hexagon
wrench to hold the stud.

SA0P7-02
F08323
Suspension Support
Spring Support
Reinforcement
Washer TankInsulator
Coil Spring
Brake Caliper
Front Fender Splash Shield
Non-reusable part Stabilizer BarCotter PIn Bushing
Front
Shock
Absorber Upper
Suspension
Arm Plug

ABS Speed SensorFront Shock Absorber
Assembly
SA-28
- SUSPENSION AND AXLEFRONT UPPER SUSPENSION ARM
1718 Author
: Date
:
1997 SUPRA (RM502U)
FRONT UPPER SUSPENSION ARM
COMPONENTS

SA0P8-01
SA3578
R07239
SST
- SUSPENSION AND AXLEFRONT UPPER SUSPENSION ARM
SA-29
1719 Author
: Date
:
1997 SUPRA (RM502U)
REMOVAL
1. REMOVE FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE BRAKE CALIPER
(a) Remove the 2 bolts and brake caliper from the steering
knuckle.
Torque: 118 N´m (1,200 kgf´cm, 87 ft´lbf)
(b) Support the brake caliper securely.
3. DISCONNECT ABS SPEED SENSOR AND WIRE HAR-
NESS CLAMP
(a) Remove the bolt and disconnect the speed sensor from
the steering knuckle.
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
(b) Remove the 3 bolts and disconnect the wire harness
clamp to prevent the wire harness being damaged when
removing or installing the through bolt.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
4. DISCONNECT UPPER SUSPENSION ARM
(a) Remove the cotter pin and the nut.
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
(b) Using SST, disconnect the upper suspension arm from
the steering knuckle.
SST 09628-6201 1
5. REMOVE FRONT FENDER SPLASH SHIELD
6. LH side only:
MOVE WASHER TANK
(a) Remove the 2 washer tank set bolts.
(b) Move the washer tank away from the body.
7. REMOVE UPPER SUSPENSION ARM
(a) Remove the nut, 2 washers and bolt.
Torque: 164 N´m (1,670 kgf´cm, 121 ft´lbf)
HINT:
At the time of installation, after stabilizing the suspension,
torque the nut.
(b) Remove the upper suspension arm.

SA0PC-02
W02908
ABS Speed Sensor
Brake Caliper
Adjusting Cam Plate
Rear Adjusting Cam
Lower Suspension Arm
Engine Under Cover
Non-reusable partFront Adjusting Cam Adjusting Cam Plate
Lower Suspension
Arm Bracket StayStabilizer Bar
Clip Shock Absorber
Bracket
SA-32
- SUSPENSION AND AXLEFRONT LOWER SUSPENSION ARM
1722 Author
: Date
:
1997 SUPRA (RM502U)
FRONT LOWER SUSPENSION ARM
COMPONENTS

SA0PK-02
W00616
Washer
Drive Shaft
Parking Brake CableBrake Caliper
Hub Bolt ABS Speed
SensorUpper Suspension Arm
Shoe Guide Plate
Lower Suspension
Arm No. 1Rear Shock
Absorber
Parking Brake
Exhaust Pipe Supprot
O-Ring Lower Suspension
Arm No. 2
Lower Suspension
Arm BraceStrut Rod
Exhaust PipeCotter Pin
Exhaust Pipe Supprot
RingDisc
Lock Cap

Non-reusable part
- SUSPENSION AND AXLEREAR AXLE HUB
SA-41
1731 Author
: Date
:
1997 SUPRA (RM502U)
REAR AXLE HUB
COMPONENTS

SA0PL-02
Z18437
R 1111 0
- SUSPENSION AND AXLEREAR AXLE HUB
SA-43
1733 Author
: Date
:
1997 SUPRA (RM502U)
REMOVAL
1. REMOVE REAR WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE BRAKE CALIPER AND DISC
(a) Remove the 2 bolts and brake caliper from the rear axle
hub.
Torque: 104 N´m (1,065 kgf´cm, 77 ft´lbf)
(b) Support the brake caliper securely.
(c) Place matchmarks on the disc and axle hub.
(d) Remove the disc.
3. CHECK BEARING BACKLASH AND AXLE HUB DEVI-
ATION
(a) Using a dial indicator near the center of the axle hub and
check the backlash in the bearing shaft direction.
Maximum: 0.05 mm (0.0020 in.)
If the backlash exceeds the maximum, replace the bearing.
(b) Using a dial indicator, check the deviation at the surface
of the axle hub outside the hub bolt.
Maximum: 0.05 mm (0.0020 in.)
If the deviation exceeds the maximum, replace the axle hub.
4. REMOVE DRIVE SHAFT LOCK NUT
(a) Install the disc and brake caliper.
Torque: 104 N´m (1,065 kgf´cm, 77 ft´lbf)
(b) Remove the cotter pin and lock cap.
(c) With applying the brakes, remove the nut.
Torque: 289 N´m (2,950 kgf´cm, 213 ft´lbf)
(d) Remove the brake caliper and disc.
5. REMOVE DRIVE SHAFT (See page SA-51)
6. REMOVE PARKING BRAKE SHOE
(See page BR-60)
7. DISCONNECT ABS SPEED SENSOR
Remove the bolt and disconnect the ABS speed sensor.
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
8. DISCONNECT PARKING BRAKE CABLE
(a) Remove the 2 parking brake cable set bolts.
Torque: 8.0 N´m (80 kgf´cm, 69 in.´lbf)
(b) Remove the 2 backing plate set bolts.
Torque: 26 N´m (260 kgf´cm, 19 ft´lbf)
(c) Remove the bolt and shoe guide plate.
Torque: 18 N´m (185 kgf´cm, 13 ft´lbf)

SA0PR-02
Z08967
TailpipeCenter Pipe
R07037
Matchmarks
R07024
R06937
- SUSPENSION AND AXLEREAR DRIVE SHAFT
SA-51
1741 Author
: Date
:
1997 SUPRA (RM502U)
REMOVAL
1. REMOVE REAR WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. DISCONNECT EXHAUST PIPE SUPPORTS
(a) Remove the 2 exhaust pipe support rings.
(b) Support the exhaust pipe securely.
(c) Remove the 2 exhaust pipe support O-rings.
3. REMOVE COTTER PIN, LOCK CAP AND LOCK NUT
(a) Remove the cotter pin and lock cap.
(b) With applying the brakes, remove the nut.
Torque: 289 N´m (2,950 kgf´cm, 213 ft´lbf)
4. REMOVE LOWER SUSPENSION ARM BRACE
Remove the 4 bolts and lower suspension arm brace.
Torque: 18 N´m (180 kgf´cm, 13 ft´lbf)
5. REMOVE REAR DRIVE SHAFT
(a) Place matchmarks on the drive shaft and side gear shaft.
(b) 2JZ-GE:
Using 8 mm hexagon wrench, remove the 6 hexagon
bolts and 3 washers with applying the brakes.
Torque: 68 N´m (695 kgf´cm, 50 ft´lbf)
(c) 2JZ-GTE:
Using a 10 mm hexagon wrench, remove the 6 hexagon
bolts and 2 washers with applying the brakes.
Torque: 83 N´m (850 kgf´cm, 61 ft´lbf)
(d) Disconnect the inboard joint from the differential side gear
shaft.
(e) Hold the inboard joint side of the drive shaft so that the
outboard joint side does not bend too much.
(f) Using a hammer, lightly tap the end of the drive shaft to
disengage the axle hub and remove the drive shaft.
NOTICE:

Be careful not to damage the boots and speed sensor
rotor of the drive shaft, and oil seal of the axle hub.

At the time of installation, make sure the outboard
joint side of the drive shaft does not bend too much.