Page 889 of 2053
SSANGYONG MY2002
3C-2 PROPELLER SHAFT
COMPONENT LOCATOR
KAA3C010
1 Front Propeller Shaft
2 Bolt
3 Nut
4 Washer
5 Bolt6 Rear Propeller Shaft
7 Bolt
8 Nut
9 Washer
10 Bolt
Page 890 of 2053
PROPELLER SHAFT 3C-3
SSANGYONG MY2002
PROPELLER SHAFT
Inspection Procedure
1. Visually check the propeller shaft.
2. Using a dial indicator, measure propeller shaft
runout by turning the shaft. If runout exceeds limit,
replace the propeller shaft or correct it.
Adjustment Notice
DIAGNOSTIC INFORMATION AND PROCEDURES
KAA3C020
Specification 0.4 mm (0.016 inch)
3. Measure the universal joint starting torque.
Adjustment Notice
Specification 0.54 N•m (4.78 lb-in)
KAA3C030
4. Measure the spider outer diameter.
Adjustment Notice
Specification 16.668 mm (0.656 inch)
KAA3C040
4. Measure the spider outer diameter.
Adjustment Notice
Specification 0.064 mm (0.0025 inch)
KAA3C050
Page 891 of 2053
SSANGYONG MY2002
3C-4 PROPELLER SHAFT
KAA3C070
KAA3C080
KAA3C060
ON-VEHICLE SERVICE
FRONT PROPELLER SHAFT
Removal and Installation Procedure
1. Raise and suitably support the vehicle.
2. Remove the front propeller shaft-to-front axle
assembly bolts.
Installation Notice
REPAIR INSTRUCTIONS
Tightening Torque7.0 - 8.5 kgm
Make alignment marks on the front propeller
shaft and front axle housing.
3. Remove the front propeller shaft-to-transfer case
bolts.
Installation Notice
Tightening Torque8.1 - 8.9 kgm
4. Remove the front propeller shaft.
5. Installation should follow the removal procedure in
the reverse order.
REAR PROPELLER SHAFT
Removal and Installation Procedure
1. Raise and suitably support the vehicle.
2. Remove the rear propeller shaft-to-rear axle assem-
bly bolts.
Installation Notice
Tightening Torque7.0 - 8.5 kgm
Make alignment marks on the rear propeller
shaft and rear axle housing.
Page 892 of 2053
PROPELLER SHAFT 3C-5
SSANGYONG MY2002
KAA3C090
3. Remove the rear propeller shaft-to-transfer case
bolts.
Installation Notice
Tightening Torque8.1 - 8.9 kgm
4. Remove the rear propeller shaft.
5. Installation should follow the removal procedure in
the reverse order.
Page 893 of 2053
SSANGYONG MY2002
3C-6 PROPELLER SHAFT
UNIT REPAIR
PROPELLER SHAFT
Removal and Installation Procedure
1. Remove the front propeller shaft. Refer to “Front
Propeller Shaft” in this section.
2. Place alignment marks before removing the spider.
KAA3C100
KAA3C120
KAA3C110
KAA3C130
3. Using a snap ring pliers, remove the snap ring.
4. Slightly tapping the yoke shoulder using a brass
hammer, remove the bearing. Remove the
remaining bearings in the same way.
5. Disassemble the universal joint parts.
Installation Notice:
Clean the disassembled parts and replace them
if damaged.
Apply grease to the inner of the bearing cap of
the needle roller bearing and assemble the needle
roller.
GreaseEP#2
Page 894 of 2053
PROPELLER SHAFT 3C-7
SSANGYONG MY2002
55
63
55
63 Front Propeller Shaft-to-Front Axle Assembly
Front Propeller Shaft-to-Transfer Bolts
Rear Propeller Shaft-to-Rear Axle Assembly
Rear Propeller Shaft-to-Transfer BoltsN•m Application
Lb-InLb-Ft
75 - 85
81 - 89
70 - 85
81 - 89-
-
-
-
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Page 895 of 2053

SECTION 3D
REAR AXLE
TABLE OF CONTENTS
General Description and Operation.................3D-2
Specifications...................................................3D-2
Fastener Tightening Specifications..................3D-2
Diagnostic Information and Procedures........3D-3
Component Locator .........................................3D-4
Rear Axle Assembly .........................................3D-4
Cross Sectional View........................................3D-5
Rear Axle Shaft Assembly...............................3D-6
Maintenance and Repair..................................3D-8
On-Vehicle Service ..............................................3D-8Axle Shaft Assembly (With Disc Brake)..........3D-8
Axle Shaft Assembly (With Drum Brake)...... 3D-11
Rear Axle Housing .......................................... 3D-13
Unit Repair....................................................... 3D-18
Axle Assembly............................................... 3D-18
Differential Gear Assembly............................ 3D-20
Drive Shaft...................................................... 3D-25
Special Tools and Equipment....................... 3D-26
Special Tools Table........................................ 3D-26
Page 896 of 2053
SSANGYONG MY2002
3D-2 REAR AXLE
Disc Brake
Drum Brake50 - 65
4 - 8
85 - 105
50 - 65
150 - 180
30 - 45
30 - 45
150 - 180
150 - 180
70 - 80
12 - 23
6 - 8
1 - 19Lb-Ft Axle Shaft Type
Axle Housing Type
Differential
Reduction Ratio
OilType
Gear
Gasoline + M/T
Diesel + M/T
Gasoline + A/T
Diesel + A/T
Capacity
SpecificationSemi-floating
Build up
Conventional Type
Hypoid Gear
3.73
4.27
4.56
4.89
1.9
SAE 80W/90 or API GL-5
GENERAL DESCRIPTION AND OPERATION
SPECIFICATIONS
37 - 48
35 - 71
63 - 77
37 - 48
111 - 133
22 - 23
22 - 23
111 - 133
111 - 133
52 - 59
9 - 17
53 - 71
11 - 14 Flange fixing Bolt
Dust shield Bolt
Caliper Bolt
Fixing NutN
z z z z
zm ApplicationLb-In
-
-
-
-
-
-
-
-
-
-
-
-
-
FASTENER TIGHTENING SPECIFICATIONS
Rod Bolt
Shock absorber Bolt
Stabilizer bar cap bolt
Upper arm nut
Lower arm nut
Propeller shaft fixing bolt
LCRV Mounting Bolt
Air Breather Hose Bolt
Brake oil pipe (M10)