1997 RENAULT KANGOO wiring

v0406.0
IMMOBILISER
Fault finding - Fault Chart (diesel version)82
AFTER REPAIRCarry out a conformity check.
Check that the immobiliser system is working correctly.
Erase fault memory G0**.
Fault Chart 5IMMOBILISER WARNING LIGHT REMAINS PERMANENTLY ILLUMINATED (even
when ignition turned off ) OR REMAINS PERMANENTLY EXTINGUISHED
Check that decoder unit programming has been properly carried out.NOTES
no Replace the fuse.
yes
Check the condition of the +before ignition
fuse.
Is the fuse in good condition?
no Repair the wiring.
yes
Check continuity and insulation from earth
of the wiring between track A5 of the 18
track decoder unit connector and the
instrument panel .
Is the wiring in good condition?
Carry out the following tests to determine the
faulty component :
- If the immobiliser warning light is
illuminated , disconnect the 18 track
decoder unit connector and check that
the immobiliser warning light
extinguishes,
- If the immobiliser warning light is
extinguished , connect track A5 of the
decoder unit connector to a vehicle earth
and check that the immobiliser warning
light illuminates.
Does the immobiliser warning light
illuminate correctly during the test?
no Replace the instrument panel .
Replace the decoder unit .
yes
yes
Check that bargraph 5LH is extinguished .
Is bargraph 5LH extinguished ?no
Refer to the chart for bargraph 5LH in the
section "Fault finding - Interpretation of
XR25 bargraphs "
82-32

v0406.0
IMMOBILISER
Fault finding - Aid
82
REMOVAL- REFITTING OF THE CLIPS
To remove the clips and the wiring tabs of the two decoder unit connectors, the kit Elé. 1263 MUST be
used.The connector and the wiring could be irreparably damaged if this tool is not used.
Use the black tool to unclip the modules.
Use the brown tool to remove the clips.
96031R
82-41

AIRBAG ANDPRETENSIONERS
FAULT FINDING
SUMMARY
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 01
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 02
XR25 fiche . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 05
Interpretation of XR25 bargraphs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 07
Checking conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Checking the pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Page

1EC761.0
AIRBAG - SEAT BELT PRETENSIONERS
Fault finding -Introduction
CONDITIONS FOR THE APPLICATION OF THE CHECKS DEFINED IN THIS FAULT FINDING
The checks defined in this fault finding should only be applied to a vehicle when the fault bargraph is
illuminated, indicating that the fault is present on the vehicle at the time of checking. Only a computer
fault will require replacement of the computer, whether the bargraph is permanently illuminated or
flashing .
If the fault is not present but simply memorised, the bargraph flashes and application of the checks
recommended in the fault finding section will not allow the origin of the fault to be found. In this case,
only a check of the wiring and the connection of the component in question must be carried out (it is
possible to test the wiring concerned in fault finding mode to try to obtain permanent illumination of the
bargraph ).
TOOLING REQUIRED FOR OPERATIONS ON THE AIRBAG AND SEAT BELT PRETENSIONER SYSTEMS :
- XR25 (with minimum XR25 cassette N° 16).
- XRBAG the updated N° 3 version (with the new measuring lead and its adaptors as well as the 30 track
adaptor for operations on the computer connector).
REMINDER:
When carrying out an operation on the airbag/seat belt pretensioner systems , it is essential to lock the
computer with the XR25 command G80* to avoid all risk of triggering at the wrong time (all firing lines
will be inhibited). This operating mode will be indicated by illumination of the warning light on the
instrument panel.
Never carry out any measuring operations on the airbag and pretensioners trigger lines with equipment
other than the XRBAG.
Before using a dummy ignition module, ensure that its resistance is between 1.8 and 2.5 ohms.
Only 30 track connector computers with airbag(s) function are able to be tested with the XR25.
Computers with the pretensioner function only must be checked with the XRBAG by following the checks
described in the fault finding section.
The ignition must be switched off, then on again to make the warning light extinguish following erasure
of the memory using the command G0**.
88
88-1

1EC761.0
AIRBAG - SEAT BELT PRETENSIONERS
Fault finding -Wiring
Fault finding - XRBAG fiche
Pretensioner only
88
DI8811.1
Correct insulation value: display≥ 100 h or 9999 flashing
PRETENSIONERS
Measuring point Correct Value
C0, C1 and C3 1.6 to 4.6 Ω
AIndependent unit
BDriver seat
CPassenger seat
DPretensioners
+ 12 V
Earth
H
88-2

1EC761.0
AIRBAG - SEAT BELT PRETENSIONERS
Fault finding -Wiring
Fault finding - XRBAG Fiche
Pretensioner and driver airbag
88
DI8812.3
Correct insulation value : display≥ 100 h or 9999 flashing
PRETENSIONERS
Measuring point Correct value
C0, C1 and C3 1.6 to 4.6 Ω
AIRBAG
Measuring point Correct value
C0, C2 and C4 2 to 9.4 Ω
CT Rotary switch
A1 +12 Volts
A3 Earth
A2 Warning light
B1
B2Diagnostic socket A Central unit
B Driver seat
C Passenger seat
D Pretensioners
E Driver’s airbag ignition module
88-3

1EC761.0
AIRBAG - SEAT BELT PRETENSIONERS
Fault finding -Wiring
Fault finding - XRBAG Fiche
Pretensioner , driver’s airbag and passenger’s airbag
88
DI8813.2
PRETENSIONERS
Measuring point Correct value
C0, C1 and C3 1.6 to 4.6 Ω
AIRBAG
Measuring point Correct value
Driver C0, C2 and C4 2 to 9.4 Ω
Passenger C0 and C4 1.6 to 4.6 Ω
CT Rotary switch
A1 +12 Volts
A3 Earth
A2 Warning light
B1
B2Diagnostic socket A Central unit
B Driver’s seat
C Passenger’s seat
D Pretensioners
E Driver’s airbag ignition module
G Passenger’s airbag ignition module
Correct insulation value : display≥ 100 h or 9999 flashing
88-4

1EC761.0
AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Interpretation of XR25 bargraphs
Bargraph 5 left hand side illuminated Fiche n° 49
Resistance on the driver’s airbag line
XR25 aid :*05 : CC : Short-circuit
CO : Open circuit
5
Never carry out measurements on the trigger lines with equipment other than the
XRBAG.NOTES
Lock the computer with the command G80* on the XR25.
Switch off the ignition and remove the two mounting bolts of the steering wheel cushion.
Check that it is correctly connected.
Disconnect the steering wheel cushion and connect a dummy ignition module to the ignition module
connector . Switch on the ignition and carry out an XR25 check.
Replace the airbag cushion if the fault has been memorised (fault no longer declared).
The XRBAG tool MUST be used for checking resistance at point C2 of the driver’s airbag circuit.
If the value obtained is not correct, replace the rotary switch below the steering wheel.
Reconnect the rotary switch below the steering wheel, disconnect the computer connector and fit the 30
track adaptor.
The XRBAG tool MUST be used for checking resistance on the wire marked B on the adaptor.
If the value obtained is not correct,
check the 30 track connector connection (tracks 10 and 11) and
replace the wiring if necessary.
If the checks carried out have not proven the existence of a fault, replace the airbag computer (consult
the section "Aid" for this operation).
Reconnect the driver’s airbag ignition module and remount the steering wheel cushion.
With the ignition switched off, disconnect, then reconnect the connector for the rotary switch below the
steering wheel.
Operate on the connection if bargraph 5 left hand side begins to flash .
Erase the computer memory using the command G0** then switch off the ignition.
carry out another check with the XR25 and, if there is no fault, unlock the
computer using command G81*.
Destroy the airbag cushion if it has been replaced (tool Elé. 1287).
AFTER REPAIR
88
88-10