1997 RENAULT KANGOO ESP

v0406.0
IMMOBILISER
Fault finding - Checking conformity
82
If a fault bargraph illuminates, refer to the corresponding fault chart.NOTES
Order of
operationsFunction to be
checkedAction Bargraph Display and notes
16Information on
programming or
resynchronisation of
PLIP in progressIlluminated if programming or
resynchronisation in progress
(PLIP).
17Programming not
carried out for PLIP
informationIlluminated if programming
not carried out (PLIP).
18 Programming of 1st
key informationNot used.
19 Programming not
carried out for key
informationIlluminated if programming
not carried out (key).
20Programming not
confirmed for key
informationIlluminated if programming
not confirmed (key).
G60* : changes to 1 when
setting is completed.
21Sending of
information is blocked
Enter security code
17
18
19
17
19
20
82-38

1EC761.0
AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Interpretation of XR25 bargraphs
Bargraph 6 left hand side illuminated Fiche n° 49
Resistance on line 1 of the passenger’s airbag
XR25 aid :*06 : CC : Short circuit
CO : Open circuit
6
Never carry out measurements on the trigger lines with equipment other than the
XRBAG. On this vehicle "line 1" corresponds to the single trigger line of the
passenger’s airbag module .
NOTES
Lock the computer using command G80* on the XR25.
Switch off the ignition, disconnect the computer connector and fit the 30 track adaptor.
The XRBAG tool MUST be used for checking resistance on the wire marked C on the adaptor.
Is the value obtained correct?
Reconnect the computer and the ignition module of the passenger’s airbag module , then switch on the
ignition again.
Carry out an XR25 check.
If the kit still indicates the presence of a line 1 passenger’s airbag fault and and the checks carried out
show no evidence of a fault, replace the airbag computer (consult the section "Aid" for this operation).
If the value obtained is correct at wire C on the adaptor, check the condition of the
computer connection .YES
If the value obtained is not correct at wire C on the adaptor, check the 30 track
connector connection (tracks 6 and 7).NO
If the value remains incorrect, switch off the ignition and remove the dashboard to
gain access to the wiring of the passenger’s airbag module . Disconnect the ignition
module of the passenger’s airbag module, connect a dummy ignition module to the
ignition module , then use the XRBAG to measure the resistance on the wire marked C
on the adaptor.
If the value obtained is correct , replace the passenger’s airbag module .
If the value obtained is not correct, replace the airbag wiring.
Erase the computer memory using the command G0** then switch off the ignition.
Carry out another XR25 check and if there is no fault, unlock the computer using
command G81*.
Destroy the airbag cushion if it has been replaced (tool Elé. 1287).
AFTER REPAIR
88
88-12

1EC761.0
AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Interpretation of XR25 bargraphs
Erase the computer memory using the command G0** then switch off the ignition.
Carry out another XR25 check and if there is no fault, unlock the computer using
command G81*.
Destroy the airbag cushion if it has been replaced (tool Elé. 1287).
AFTER REPAIR
Bargraph 7 right hand side illuminated Fiche n° 49
Insulation of line 1 or 2 of the passenger’s airbag
XR25 aid :*27 : CC.1 : Short circuit at 12 volts
CC.0 : Short circuit to earth
7
Never carry out measurements on the trigger lines with equipment other than the
XRBAG. On this vehicle "line 1" corresponds to the single trigger line of the
passenger’s airbag module .
NOTES
Reconnect the computer and the ignition module of the passenger’s airbag module , then switch on the
ignition again.
Carry out an XR25 check.
If the kit still indicates the presence of a passenger’s airbag line fault and the checks carried out show no
evidence of a fault, replace the airbag computer (consult the section "Aid" for this operation).
It the value obtained is correct at wire C on the adaptor, check the condition of the
computer connection .YES
If the value obtained is not correct at the adaptor wire, check the 30 track connector
connection (tracks 6/7).NO
If the value remains incorrect , replace the airbag wiring.
Lock the computer using command G80* on the XR25.
Switch off the ignition, disconnect the computer connector and fit the 30 track adaptor.
The XRBAG tool MUST be use for measuring insulation appropriate to the type of fault on the wire
marked C on the adaptor.
Is the value obtained correct? ?
88
88-13

1EC761.0
AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Checking conformity
Only carry out this conformity check after a complete XR25 check.NOTES
Order of
operationsOperation to be
checked Action Bargraph Display and remarks
1 XR25 dialogueD49
(selector on
S8)
I.Ab
2 Computer Conformity
#022 2
3 Computer
Configuration Ensure that the computer
configuration shown by these 3
bargraphs corresponds to the
vehicle equipment.
4Warning light
operation - check
computer
initialisation Switch on the
ignition 3 second illumination of the
warning light when turning on
the ignition (consult fault
finding if it remains
illuminated or if it does not
illuminate).
17 / 18 / 19
88
88-22