1997 RENAULT KANGOO ignition

JSA052.0
INJECTION
Fault finding - Interpretation of XR25 bargraphs17
D7F 710
engine -
55 tracks
Erase the computer memory using G0**.
Try to start the engine. Switch the ignition on, then deal with the other faults.
Remember to carry out a status and parameter check.AFTER REPAIR
Bargraph 2 LH side illuminated. Fiche n° 27 side 1/2
COMPUTER CIRCUIT
XR25 aid: computer faulty

2
NoneNOTES
The computer is incorrect or faulty.
Replace the computer.
17-156

JSA052.0
INJECTION
Fault finding - Interpretation of XR25 bargraphs17
D7F 710
engine -
55 tracks
Erase the computer memory using G0**.
Try to start the engine. Switch the ignition on, then deal with the other faults.
Remember to carry out a status and parameter check.AFTER REPAIR
Bargragh 2 RH side illuminated Fiche n° 27 side 1/2
IMMOBILISER CIRCUIT
XR25 aid:*22 = 1 dEF CO, CC- or CC+ line 37 of the computer
*22 = 2 dEF Refer to the immobiliser fault finding section

2
Ignore this bargraph if the vehicle is not fitted with an immobiliser.NOTES
Connect the bornier in place of the computer and check the insulation, continuity and that there is no
interference resistance on the wiring on track 37 of the computer.
Repair if necessary.
If the fault persists, refer to the immobiliser fault finding.
17-157

Connect the bornier in place of the computer and check the insulation and continuity of the line.
Computer 20 2 Air temperature sensor
Computer 46 1 Air temperature sensor
Repair if necessary.
JSA052.0
INJECTION
Fault finding - Interpretation of XR25 bargraphs17
D7F 710
engine -
55 tracks
Erase the computer memory using G0**.
Try to start the engine. Switch the ignition on, then deal with the other faults.
Remember to carry out a status and parameter check.AFTER REPAIR
Bargraph 3 LH side illuminatedFiche n° 27 side 1/2
AIR TEMPERATURE SENSOR CIRCUIT
XR25 aid:CO, CC- or CC+line 20 or 46 of the computer

3
If BG 6RH is also illuminated, check line 46 of the computer.NOTES
Check the resistance of the sensor. Replace if necessary.
The fault persists! Replace the injection computer.
IMPORTANT: The computer has probably been damaged by an electric shock. The cause of the damage
must be found before fitting a new computer.
17-158

Connect the bornier in place of the computer and check the insulation and continuity of the line:
Computer 17 C Oxygen sensor
Repair if necessary.
JSA052.0
INJECTION
Fault finding - Interpretation of XR25 bargraphs17
D7F 710
engine -
55 tracks
Turn the engine, switch the ignition on and erase the computer memory using
G0**. Try to start the engine. Switch the ignition on, then deal with the other
faults. Remember to carry out a status and parameter check.AFTER REPAIR
Bargraph 3 RH side illuminated or flashing Fiche n° 27 side 1/2
OXYGEN SENSOR CIRCUIT
XR25 aid:CO, CC- or CC+line 17 of the computer
CO line 18 of the computer

3
If BG 3RH is flashing, increase the engine speed to 2500rpm for 5 minutes.
If BG 3RH becomes permanently illuminated, deal with the fault.
NOTES
Check the connection and the condition of the connector on the oxygen sensor.
Check, ignition on during the timed phase, for :
- earth on track B of the oxygen sensor,
- + 12 V after the fuel pump relay on track A of the oxygen sensor.
Repair if necessary.
Check for the presence of earth on track 18 of the injection computer.
Repair if necessary.
The fault persists. Replace the oxygen sensor.
The fault persists! Replace the injection computer.
IMPORTANT: The computer has probably been damaged by an electric shock. The cause of the damage
must be found before fitting a new computer.
17-159

Connect the bornier in place of the computer and check the insulation and continuity of the line:
Computer 44 1 Coolant temperature sensor
Computer 15 2 Coolant temperature sensor
Repair if necessary.
JSA052.0
INJECTION
Fault finding - Interpretation of XR25 bargraphs17
D7F 710
engine -
55 tracks
Erase the computer memory using G0**.
Try to start the engine. Switch the ignition on, then deal with the other faults.
Remember to carry out a status and parameter check.AFTER REPAIR
Bargraph 4 LH side illuminated Fiche n° 27 side 1/2
COOLANT TEMPERATURE SENSOR CIRCUIT
XR25 aid :CO, CC- or CC+line 44 or 15 of the computer

4
If BG 6LH or BG 5LH is also illuminated , check line 44 of the computer. For certain
faults, BG 4LH is only permanently illuminated when the engine is running.NOTES
The fault persists! Replace the injection computer.
IMPORTANT: The computer has probably been damaged by an electric shock. The cause of the damage
must be found before fitting a new computer.
Check the resistance of the sensor. Replace it if necessary.
17-160

Connect the bornier in place of the computer and check the insulation, continuity and that there is no
interference resistance on the line:
Computer 12 B1 Vehicle speed sensor
Repair if necessary.
JSA052.0
INJECTION
Fault finding - Interpretation of XR25 bargraphs17
D7F 710
engine -
55 tracks
Erase the computer memory using G0**.
Try to start the engine. Switch the ignition on, then deal with the other faults.
Remember to carry out a status and parameter check.AFTER REPAIR
Bargraph 4 RH side illuminated or flashing Fiche n° 27 side 1/2
VEHICLE SPEED CIRCUIT
XR25 aid:CO, CC- or CC+ line 12 of the computer

4
Carry out a road test if the BG 4RH is flashing.NOTES
Check the sensor is correctly positioned.
Check on the vehicle speed sensor for:
- earth on track B2,
-+ 12 after ignition feed on track A.
Repair if necessary.
The fault persists! Replace the sensor.
The fault persists! Replace the injection computer.
IMPORTANT: The computer has probably been damaged by an electric shock. The cause of the damage
must be found before fitting a new computer.
17-161

Connect the bornier in place of the computer and check the insulation, continuity and that there is no
interference resistance on the line:
Computer 45 C Pressure sensor
Computer 44 A Pressure sensor
Computer 16 B Pressure sensor
Repair if necessary.
JSA052.0
INJECTION
Fault finding - Interpretation of XR25 bargraphs17
D7F 710
engine -
55 tracks
Erase the computer memory using G0**.
Try to start the engine. Switch the ignition on, then deal with the other faults.
Remember to carry out a status and parameter check.AFTER REPAIR
Bargraph 5LH side illuminatedFiche n° 27 side 1/2
PRESSURE SENSOR CIRCUIT
XR25 aid :CO, CC- or CC+ line 45, 44 or 16 of the computer

5
If BG 6RH is also illuminated, check line 45 of the computer.
If BG 6LH or BG 4LH is also illuminated, check line 44 of the computer.NOTES
Check that the pressure sensor is connected correctly both electrically and pneumatically.
Check the conformity of the pressure sensor pipe (it must not be pierced or blocked...).
The fault persists! Replace the injection computer.
IMPORTANT: The computer has probably been damaged by an electric shock. The cause of the damage
must be found before fitting a new computer.
The fault persists! Replace the sensor.
17-162

Connect the bornier in place of the computer and check the insulation,
continuity and that there is no interference resistance on the line:
Computer 33 B Target sensor
Computer 34 A Target sensor
Repair if necessary.
JSA052.0
INJECTION
Fault finding - Interpretation of XR25 bargraphs17
D7F 710
engine -
55 tracks
Erase the computer memory using G0**.
Try to start the engine. Switch the ignition on, then deal with the other faults.
Remember to carry out a status and parameter check.AFTER REPAIR
Bargraph 5 RH side illuminated or flashingFiche n° 2 side 1/2
FLYWHEEL SIGNAL CIRCUIT
XR25 aid:*25 = CO.0 =>CO or CC- line 33 or 34 of the computer
*25 = CC.0 =
>CC- line 33 or 34 of the computer
*25 = In =
>sensor incorrectly connected
5
Try to illuminate BG 5RH when the starter is activated.
BG 5RH is often seen to flash if *25 = dEF as its permanent illumination is very
quick. In certain cases, BG 5RH may illuminate then extinguish.
NOTES
Check the resistance of the target sensor.
Replace the sensor if necessary.*25 = CO.0
*25 = CC.0
Check the condition of the flywheel, especially if it has been removed.
The fault persists! Replace the injection computer.
IMPORTANT: The computer has probably been damaged by an electric shock.
The cause of the damage must be found before fitting a new
computer.
Check the target sensor has been correctly connected (the sensor connector must
not be inverted).
Repair if necessary.*25 = In
The fault persists! Replace the sensor.
17-163