1997 RENAULT KANGOO transmission

ENGINE AND ENGINE PERIPHERALS
Engine and transmission assembly
10
Remove the suspended engine mounting cover.
13086R1
13086R
Insert a wedge between the gearbox and the sub-
frame.
Remove:
- the nut (1), then tap it with a copper hammer
to release the suspended engine mounting
stud. F8Q engine
99024R2
Fit tool Mot. 1159 between the sub-frame and the
cylinder block.
Fit tool Mot. 1159 in place of the coolant pipe
mounting on the cylinder block.
99310R
10-23

ENGINE AND ENGINE PERIPHERALS
Engine and transmission assembly
10
REFITTING
The alignment of the sub-frame with the body
will be made easier by positioning two threaded
rods Mot. 1233-01 in the two front mountings of
the sub-frame on the body.
Tighten the sub-frame mounting bolts to a torque
of:
- 6.2 daN.m at the front,
-10.5 daN.m at the rear.
Refitting is the reverse of removal.
Fit the heat shields correctly.
Apply
Loctite FRENBLOC to the caliper mounting
bolts and tighten them to the recommended tor-
que.
Press the brake pedal several times to bring the
pistons into contact with the brake pads.
Fill:
- the engine and gearbox with oil, if necessary,
- the cooling circuit and bleed it (see section 19
"Filling - bleeding"). F8Q engine
Fix tool Mot. 1040-01 underneath the sub-frame.
98755R1
Lower the lift until the tool touches the ground.
Remove the sub-frame mounting bolts and take
out the engine and transmission assembly by lif-
ting the body.
NOTE : for any operation requiring separation of
the engine, gearbox and sub-frame assembly,
take care to mark the position of Mot. 1159 on the
sub-frame.
Remove the mounting bolts (3).
12993-1R3
10-24

INJECTION
General
17
SPECIAL NOTES FOR MULTIPOINT INJECTION
• 35 track SAGEM or MAGNETI MARELLI computer for vehicles without options.
• 55 track SAGEM computer ,
SAFIR or MAGNETI MARELLI type for versions with air conditioning.
•Semi-sequential multipoint injection. Injectors controlled two by two (injectors for cylinders 1 and 4 fol-
lowed by injectors for cylinders 2 and 3).
•Semi-static ignition with dual single unit coils.
•Canister bleed solenoid valve controlled by RCO signal.
•Computer configuration depending on gearbox type (manual gearbox or automatic transmission).
•The maximum engine speed permitted is 6 200 rpm.
•Idle speed correction depending on :
- battery voltage,
- air conditioning
- power assisted steering pressostat.
•Injection warning light on instrument panel not operational.
•Use fault finding fiche n° 27. D7F Engine
FITTING A 2ND GENERATION ENGINE IMMOBILISER REQUIRES A SPECIAL PROCEDURE FOR REPLACING THE
COMPUTER.
17-4

INJECTION
General
17
SPECIAL NOTES FOR MULTIPOINT INJECTION
• 55 track SIEMENS FENIX 5 computer.
•Semi-sequential multipoint injection. Injectors are controlled two by two (injectors for cylinders 1 and 4
followed by cylinders 2 and 3).
•Semi-static ignition with dual coils.
•Canister bleed solenoid controlled by RCO signal.
•Computer configuration depending on gearbox type (manual gearbox or automatic transmission)
•Idle speed correction depending on :
- air conditioning,
- power assisted steering pressostat,
- battery voltage.
•Injection warning light on instrument panel operational.
•Use fault finding fiche n° 27.
•Maximum speed :
-6 200 rpm if 1st , 2nd or 3rd gears
-6 000 rpm if 4th,or 5th gears. E7J Engine
FITTING A 2ND GENERATION ENGINE IMMOBILISER REQUIRES A SPECIAL PROCEDURE FOR REPLACING THE
COMPUTER.
17-5

INJECTION

Computer configuration depending on gearbox type17
The screen will display :
COMPUTER CONFIGURATION DEPENDING ON GEARBOX TYPE (MANUAL GEARBOX OR AUTOMATIC
TRANSMISSION)
Each time the injection computer is replaced, it must be programmed with the type of gearbox (manual or
automatic) which is fitted in the vehicle. The computers are designed to function with either type of gearbox.
Method for configuring the computer
Connect the
XR25
Select S8
Switch on the ignition
Enter D13 then
For vehicles fitted with manual gearbox :
Enter G50* 2*
For vehicles fitted with automatic transmission :
Enter G50* 1*
if the configuration has not been made
To ensure that the computer has memorised the data correctly, switch the ignition back on , using fault fin-
ding fiche n° 27; the fault bargraph
20 LH should be extinguished, whilst the 19 LH or RH status bargraph
should be illuminated.
then if the configuration is complete
17-16