1997 RENAULT KANGOO air filter

DIESEL EQUIPMENT
Altimetric corrector
13
REFITTING
It is VITAL to remove the small filter (2) situated at
the bottom of the system using a pair of thin -
nosed pliers, and replace it with a new one.
Tighten the actuator (1) to a torque of 3 daN.m
using the socket Mot. 1440.
Place a new protective cover on the actuator.
Reconnect the two terminals to the connector.Reconnect the connector.
Replace the protective sheath on the wiring,
along with the retaining clip.
Bleed the diesel circuit using the priming pump
before starting the engine.
It is IMPERATIVE to erase the computer memory
by pressing G0**.
It is vital to road test the vehicle after this
operation.
13128R
F8Q 662
FUNCTION : it acts on the flow in proportion to altitude ; if the vehicle is running at
an altitude greater than or equal to 1 000 metres, the computer reduces the flow by
3 mm
3/stroke. The conventional flow is reestablished if the vehicle runs at an alti-
tude lower than 900 metres.
13-24

ANTIPOLLUTION
Oil vapour rebreathing
14
1 Engine
2 Oil decanter
3 Air filter
4 Inlet manifold
13042R
F8Q Engine
14-10

ANTIPOLLUTION
Exhaust gas recirculation (EGR)
14
1 EGR valve
2 EGR solenoid (ON/OFF)
3 Vacuum pump
4 Engine
5 Exhaust manifold
6 Inlet manifold
7 Air filter
8 Injection computer
9 Coolant temperature sensor
13046R
F8Q Engine
13045R
14-11

ANTIPOLLUTION
Exhaust gas recirculation (EGR)
14
SPECIAL NOTES
In order to remove the steel pipe connecting the
EGR valve to the air filter, it is necessary to
remove the
EGR valve .
12871R1
F8Q Engine
13047-1R2
To remove the EGR solenoid (2), remove the air
filter .
To remove the
EGR valve (1), remove the air filter
first, and replace the seal between the solenoid
valve and the inlet manifold after each removal
operation.
14-12

STARTING - CHARGING
Starter motor
16
REMOVAL
Place the vehicle on a two post lift.
Remove:
- the air filter inlet pipe,
- the battery,
- the computer support mounting bolts as well
as the connectors at (1), then move the
computer support/ diesel filter assembly to
one side.
13088R3
- the starter mounting bolts and the heat shield
(A),- the starter connections,
- the starter motor itself.
REFITTING
Refitting is the reverse of removal.
Check for the presence of the centring dowel,
which should be located at (B).
13087R1
F8Q Engine
16-11

INJECTION
General
17
1 Coil
2 Air filter
3 Oxygen sensor
4 Absolute pressure sensor
5 Throttle position potentiometer
6 Idle regulation stepping motor
7 Air temperature sensor
8 Injection computer
9 Inertia switch
10 Locking relay
11 Fuel pump relay
12 TDC sensor
13 Fuel vapour recycling solenoid valve
14 Coolant temperature sensor
15 Tool for removing spark plug leads
16 Pinking sensor
17 Power assisted steering pressostat
18 Pressure regulator
19 Anti-interference condenser
20 Fuel vapour absorber (canister)
LOCATION OF COMPONENTS
13081
D7F Engine
17-6

INJECTION
General
17
1 Fuel vapour recycling solenoid valve
2 Air filter
3 Pinking sensor
4 Absolute pressure sensor
5 Idle speed regulation stepping motor
6 Throttle position potentiometer
7 Air temperature sensor
8 Injection computer
9 Inertia switch
10 Fuel pump relay
11 TDC sensor
12 Coolant temperature sensor
13 Oxygen sensor
14 Coil for cylinders 2 - 3
15 Power assisted steering pressostat
16 Coil for cylinders 1 - 4
17 Fuel vapour absorber (canister)
18 Anti-interference condenser
LOCATION OF COMPONENTS
13082
E7J Engine
17-7